You are looking for information, articles, knowledge about the topic nail salons open on sunday near me how to protect tweeters from blowing on Google, you do not find the information you need! Here are the best content compiled and compiled by the Chewathai27.com team, along with other related topics such as: how to protect tweeters from blowing tweeter capacitor, how to install a resistor on a tweeter, tweeter crossover, how to install tweeters to amp, how to fix a blown speaker, how to adjust crossover on component speakers, how to avoid blowing out car speakers, how to put capacitor on tweeter
Keep the volume on your receiver at least 5-6dB below its max setting. The volume adjustment on most receivers goes from -80dB (mute) to about +16dB (max). By staying below -6dB below that max setting you can typically avoid over-driving the receiver, which could potentially damage your speakers and receiver.If the tweeter amp has enough power and the level is increased too far, the tweeter or compression horn driver will fail, even though there are no additional harmonics present. The issue is (and always was) excessive power and the increase in level below the nominal crossover frequency.In a simple passive crossover, we use a capacitor to limit the amount of low frequencies that make it to the tweeter. This does two things: 1) it protects the tweeter from the application of too much power at low frequencies, and 2) it helps us shape the response of the tweeter to match the response of the midrange.
- Use a capacitor to prevent low frequencies from damaging the tweeter. …
- Keep your hertz within the tweeter’s recommended frequency. …
- Don’t turn your speakers louder than they’re supposed to go. …
- Consider installing a two-way crossover.
Contents
How do I stop my speakers from blowing?
Keep the volume on your receiver at least 5-6dB below its max setting. The volume adjustment on most receivers goes from -80dB (mute) to about +16dB (max). By staying below -6dB below that max setting you can typically avoid over-driving the receiver, which could potentially damage your speakers and receiver.
What causes a tweeter to fail?
If the tweeter amp has enough power and the level is increased too far, the tweeter or compression horn driver will fail, even though there are no additional harmonics present. The issue is (and always was) excessive power and the increase in level below the nominal crossover frequency.
Do I need capacitor for tweeter?
In a simple passive crossover, we use a capacitor to limit the amount of low frequencies that make it to the tweeter. This does two things: 1) it protects the tweeter from the application of too much power at low frequencies, and 2) it helps us shape the response of the tweeter to match the response of the midrange.
Why do my tweeters keep blowing?
Tweeters keep blowing when they go below their recommended hertz, if they encounter too much audio clipping or compression, or if there’s not enough headroom on your amplifiers. To prevent tweeters from blowing, use the built-in capacitor or a two-way crossover to protect them from low frequencies.
What causes tweeters to burn?
DC from clipping is the most common reason for burning out tweeters. Amplifiers driven in perverse ways that leads to distortion can create DC or virtually square waves which are guaranteed to fry just about any tweeters no matter what their power handling is.
Does a capacitor improve sound quality?
A cap prevents the sound from deteriorating due to under-voltage, but doesn’t actually improve the sound. It supports the amplifier by feeding it the power it needs for short bursts. So, while not improving sound quality directly, a cap does make it easier for the amp to perform its best.
How can I protect my speakers?
- Keep them away from sunlight and water.
- Cover them during bad weather, when it’s not practical to bring them inside.
- Check mount hardware regularly.
- Check wiring regularly.
- Clean the speakers on a regular basis.
Why do I keep blowing my speakers?
Speakers generally blow out when too much electrical power is applied. They also blow out from physical damage or ageing/deterioration. Avoid blow-out by keeping speakers at safe listening levels and in safe locations. Replacing the blown parts is typically the only solution to fix blown speakers.
Can blown tweeters be repaired?
I’m afraid there is no fix for your tweeters. You’ll have to replace them. As for protecting new ones. Break the kid’s fingers if he gets near the volume control again.
Why is my tweeter crackling?
It’s clipping or an inadequate/malfunctioning crossover network on the tweeters.
How can I tell if my tweeters are blown?
Basically, play that tone at low volume and put your head holes right near the tweeter. If it is not making any sound, it is blown. If it does make sound, it might be partially damaged or work fine. If it is loud and clear, sounds like your other speakers then you are OK.
What capacitor should I use for tweeter?
Usually we use 10uf capacitor for tweeter.
What is the best frequency for tweeters?
Tweeters generally are good for around 3kHz or above, so 3kHz or 3.5kHz cutoff frequencies are usually great choices.
Do tweeters need a crossover?
Why Do You Need A Crossover? Every audio system, including the one in your car, needs a crossover to direct sound to the correct driver. Tweeters, woofers and subs should get high, mid and low frequencies respectively. Every full-range speaker has a crossover network inside.
How can I protect my speakers?
- Keep them away from sunlight and water.
- Cover them during bad weather, when it’s not practical to bring them inside.
- Check mount hardware regularly.
- Check wiring regularly.
- Clean the speakers on a regular basis.
What does adding a capacitor to a speaker do?
The job of capacitors is to allow only the high frequencies to pass. The inductor (also known as a coil or choke) assumes the opposite task by letting only the low frequencies pass. It does this by storing energy in magnetic instead of electrical form.
What is the best frequency for tweeters?
Tweeters generally are good for around 3kHz or above, so 3kHz or 3.5kHz cutoff frequencies are usually great choices.
Tweeters Keep Blowing? This Might Be Why! | Playbutton
- Article author: playbutton.co
- Reviews from users: 11117
Ratings
- Top rated: 3.1
- Lowest rated: 1
- Summary of article content: Articles about Tweeters Keep Blowing? This Might Be Why! | Playbutton Updating …
- Most searched keywords: Whether you are looking for Tweeters Keep Blowing? This Might Be Why! | Playbutton Updating Tweeters are an essential part of an audio entertainment system. Whether you’re listening to music, movies, or anything in between, your tweeters play a crucial…
- Table of Contents:
Why Are Your Tweeters Blowing Out
How Do You Stop Tweeters From Blowing
How To Check if Your Tweeters Are Blown
Conclusion
About Me
Recent Posts
![Tweeters Keep Blowing? This Might Be Why! | Playbutton](https://playbutton.co/wp-content/uploads/2021/04/wire-tweeters.jpg)
PROTECT YOUR TWEETERS! Capacitors and WHY you need them – YouTube
- Article author: www.youtube.com
- Reviews from users: 42385
Ratings
- Top rated: 3.5
- Lowest rated: 1
- Summary of article content: Articles about PROTECT YOUR TWEETERS! Capacitors and WHY you need them – YouTube Updating …
- Most searched keywords: Whether you are looking for PROTECT YOUR TWEETERS! Capacitors and WHY you need them – YouTube Updating Running component speakers “active” has many advantages, but we MUST protect our tweeters. Low frequency sound, turn on pops, or other system noise can destr…car audio fabrication, car audio, caraudiofabrication, tweeter protect, active tweeter, protect tweeter capacitor, tweeter capacitor, electrolytic capacitor, Non-Polarized Electrolytic Capacitors, polypropylene, component speakers, protect speakers, turn on pop, signal noise, blown tweeters, blown speaker
- Table of Contents:
![PROTECT YOUR TWEETERS! Capacitors and WHY you need them - YouTube](https://i.ytimg.com/vi/hscMuzfyxQ4/maxresdefault.jpg)
AV Tip: How to Avoid Blowing Out Your Speakers | Audioholics
- Article author: www.audioholics.com
- Reviews from users: 19226
Ratings
- Top rated: 3.9
- Lowest rated: 1
- Summary of article content: Articles about AV Tip: How to Avoid Blowing Out Your Speakers | Audioholics Updating …
- Most searched keywords: Whether you are looking for AV Tip: How to Avoid Blowing Out Your Speakers | Audioholics Updating Every so often some variation of this question gets asked on the Audioholics Forums, “Will I blow my speakers if I use amplifer X with speaker Y?” Here are a few tips to keep your equipment safe.
- Table of Contents:
Why Do Tweeters Blow When Amplifiers Distort?
- Article author: sound-au.com
- Reviews from users: 36712
Ratings
- Top rated: 4.7
- Lowest rated: 1
- Summary of article content: Articles about Why Do Tweeters Blow When Amplifiers Distort? Updating …
- Most searched keywords: Whether you are looking for Why Do Tweeters Blow When Amplifiers Distort? Updating ESP – The Audio Pages. Why Do Tweeters Blow When Amplifiers Distort? Find out what really happens when amplifiers cause tweeters to fail.tweeter, clipping, distortion, blow, damage, audio, crossover, passive, fi-fi, electronic
- Table of Contents:
![Why Do Tweeters Blow When Amplifiers Distort?](https://i0.wp.com/wpsites.net/wp-content/uploads/2014/06/icon-after-more-link.png)
Best way to Protect Tweeters? | Audiokarma Home Audio Stereo Discussion Forums
- Article author: audiokarma.org
- Reviews from users: 31519
Ratings
- Top rated: 3.9
- Lowest rated: 1
- Summary of article content: Articles about Best way to Protect Tweeters? | Audiokarma Home Audio Stereo Discussion Forums Pushing an amp into clipping constantly is a sure way to cook tweeters, as others have sa. Making sure you have plently of clean power and … …
- Most searched keywords: Whether you are looking for Best way to Protect Tweeters? | Audiokarma Home Audio Stereo Discussion Forums Pushing an amp into clipping constantly is a sure way to cook tweeters, as others have sa. Making sure you have plently of clean power and … I’ve read a number of things, the one Im most interesed in is the idea of fusing the tweeter leads. What is involved in this? Has anyone done it as a…
- Table of Contents:
![Best way to Protect Tweeters? | Audiokarma Home Audio Stereo Discussion Forums](https://audiokarma.org/forums/styles/default/xenforo/avatars/avatar_m.png)
why do my tweeters keep blowing | diyAudio
- Article author: www.diyaudio.com
- Reviews from users: 16867
Ratings
- Top rated: 3.4
- Lowest rated: 1
- Summary of article content: Articles about why do my tweeters keep blowing | diyAudio Generally speaking it’s because your amp is too small and starts clipping. In general, too small amps blows tweeters, too big amps blows woofers … …
- Most searched keywords: Whether you are looking for why do my tweeters keep blowing | diyAudio Generally speaking it’s because your amp is too small and starts clipping. In general, too small amps blows tweeters, too big amps blows woofers … I’ve gone through about 4 Vifa D27TG-05s in the last year and I can’t figure out why they keep blowing. I have them crossed over pretty high with solen…
- Table of Contents:
![why do my tweeters keep blowing | diyAudio](https://i0.wp.com/wpsites.net/wp-content/uploads/2014/06/icon-after-more-link.png)
Why does tweeter keep blowing? | AVForums
- Article author: www.avforums.com
- Reviews from users: 16157
Ratings
- Top rated: 3.9
- Lowest rated: 1
- Summary of article content: Articles about Why does tweeter keep blowing? | AVForums Failure in a tweeter is excessive power within the audio bandwth of the tweeter,and can be even caused by very high Frequency (above audio) … …
- Most searched keywords: Whether you are looking for Why does tweeter keep blowing? | AVForums Failure in a tweeter is excessive power within the audio bandwth of the tweeter,and can be even caused by very high Frequency (above audio) … I think i know the solution (replace amp) but just running it past you guys.
Speakers are vintage b&w dm100’s. 70w rms power handling. 6 inch mid and…
- Table of Contents:
Sections
Advertising
Organisation
Forum Information
Socialising
The HUBS
![Why does tweeter keep blowing? | AVForums](https://www.avforums.com/styles/avf/logo.og.png)
tweeter protection circuit diagram, PROTECT YOUR TWEETERS, electronics – FJM ECOM
- Article author: fjmecom.com
- Reviews from users: 46275
Ratings
- Top rated: 4.6
- Lowest rated: 1
- Summary of article content: Articles about tweeter protection circuit diagram, PROTECT YOUR TWEETERS, electronics – FJM ECOM Tagged blown tweeters, car audio, connect speakers, crossover circuit diagram speaker, crossover diagram, electronics, high bass, … …
- Most searched keywords: Whether you are looking for tweeter protection circuit diagram, PROTECT YOUR TWEETERS, electronics – FJM ECOM Tagged blown tweeters, car audio, connect speakers, crossover circuit diagram speaker, crossover diagram, electronics, high bass, … https://youtube.com/watch?v=AZWli3z79FsFor more information please visit https://electronicshelpcare.com/ https://www.pinterest.com/electrohelpcare/ https://www.facebook.com/Electronics-help-care-272370156885340/ https://www.youtube.com/channel/UCbeoDNy2iO6pwGi8cfBXbgA #tweeter#crossover#protectioncircuit#
- Table of Contents:
Published by fjm1972
Post navigation
![tweeter protection circuit diagram, PROTECT YOUR TWEETERS, electronics – FJM ECOM](https://i0.wp.com/fjmecom.com/wp-content/uploads/2019/09/maxresdefault-73.jpg?fit=1200%2C675&ssl=1)
I keep blowing tweeters Help!! | Home Theater Forum
- Article author: www.hometheaterforum.com
- Reviews from users: 41600
Ratings
- Top rated: 4.4
- Lowest rated: 1
- Summary of article content: Articles about I keep blowing tweeters Help!! | Home Theater Forum It is most likely happening because you either have too much or too little power going to the drivers. Most likely not enough. The amplfifer is being driven to … …
- Most searched keywords: Whether you are looking for I keep blowing tweeters Help!! | Home Theater Forum It is most likely happening because you either have too much or too little power going to the drivers. Most likely not enough. The amplfifer is being driven to … Hi gang
Over a period of time, I have managed to damage 3 pairs of HF units, usually as a result of sudden peaks in the sound program.
The most recent… - Table of Contents:
![I keep blowing tweeters Help!! | Home Theater Forum](https://i0.wp.com/wpsites.net/wp-content/uploads/2014/06/icon-after-more-link.png)
Why Do Tweeters Blow When Amplifiers Distort?
- Article author: sound-au.com
- Reviews from users: 1742
Ratings
- Top rated: 3.9
- Lowest rated: 1
- Summary of article content: Articles about Why Do Tweeters Blow When Amplifiers Distort? Because of the nature of music and the over-use of compression, it is not only tweeters that are at risk. Woofers can also be damaged, due … …
- Most searched keywords: Whether you are looking for Why Do Tweeters Blow When Amplifiers Distort? Because of the nature of music and the over-use of compression, it is not only tweeters that are at risk. Woofers can also be damaged, due … ESP – The Audio Pages. Why Do Tweeters Blow When Amplifiers Distort? Find out what really happens when amplifiers cause tweeters to fail.tweeter, clipping, distortion, blow, damage, audio, crossover, passive, fi-fi, electronic
- Table of Contents:
![Why Do Tweeters Blow When Amplifiers Distort?](https://i0.wp.com/wpsites.net/wp-content/uploads/2014/06/icon-after-more-link.png)
See more articles in the same category here: Top 122 tips update new.
Tweeters Keep Blowing? This Might Be Why!
As an Amazon Associate I earn from qualifying purchases. Read full affiliate disclaimer.
Tweeters are an essential part of an audio entertainment system. Whether you’re listening to music, movies, or anything in between, your tweeters play a crucial role in the speakers’ high frequencies. However, improper usage can cause them to blow, sending loud pop noises and ruining their clarity.
Tweeters keep blowing when they go below their recommended hertz, if they encounter too much audio clipping or compression, or if there’s not enough headroom on your amplifiers. To prevent tweeters from blowing, use the built-in capacitor or a two-way crossover to protect them from low frequencies.
Throughout this post, we’ll also cover a handful of reasons your tweeters keep blowing out, how you can prevent it from happening, and tips to check if your tweeters are permanently damaged. You’ll also learn what to do if they’re crackling or blowing out too often.
Why Are Your Tweeters Blowing Out?
Are you using a custom set of speakers, but the tweeters keep blowing? This common issue stems from countless problems, including incorrect frequencies, compression, clipping, and more.
Protecting your tweeters starts at the source, so let’s break down a handful of reasons your tweeters are experiencing problems below:
They’re going too far below the recommended hertz. Many tweeters blow out when the hertz is too low. Tweeters are designed to handle a high frequency, so dipping too low (below the average of 2,000 hertz) can cause irreparable damage.
Many tweeters blow out when the hertz is too low. Tweeters are designed to handle a high frequency, so dipping too low (below the average of 2,000 hertz) can cause irreparable damage. Too much clipping and compression can damage a tweeter. Clipping and compressing your audio files might save a lot of file space, but it’ll cause all sorts of issues with your tweeters and subwoofers. The last thing you want is to sacrifice your sound system for a slightly smaller storage file.
Clipping and compressing your audio files might save a lot of file space, but it’ll cause all sorts of issues with your tweeters and subwoofers. The last thing you want is to sacrifice your sound system for a slightly smaller storage file. There’s not enough headroom on your amplifiers to accommodate the dB. Many tweeters have a decibel ceiling. If your amplifiers go too high, it can blow the tweeters. This problem only progresses if you don’t pay attention to the dB because it’s not always noticeable right away. It can slowly get worse over time.
Many tweeters have a decibel ceiling. If your amplifiers go too high, it can blow the tweeters. This problem only progresses if you don’t pay attention to the dB because it’s not always noticeable right away. It can slowly get worse over time. You might’ve chosen the wrong speakers, amplifiers, and other audio equipment. There are several pieces involved in the process, all of which can alter the hertz’ range. If your tweeters are exposed to extremely low or high hertz, they’ll likely blow or become partially damaged.
These four reasons are undeniably the most common problems associated with blown tweeters, but many more issues can land your speakers in hot water.
For example, the extremely loud volume will shred your tweeters and subwoofers. It’s best to check their recommendations before blaring the noise, even if they’re capable of doing so.
Knowing the causes is half of the battle, but you can check out some preventative steps to protect your tweeters in the next section.
Related article: Can You Wire Tweeters in Series?
How Do You Stop Tweeters From Blowing?
Replacing tweeters can be tedious, expensive, and difficult. If you’re trying to keep it from happening, or you’re wondering why they keep blowing, you’re in the right place.
Many safety techniques, such as using a crossover or capacitor, can make a world of difference for your sound system.
Here’s the five-step process to preserve your tweeters:
Use a capacitor to prevent low frequencies from damaging the tweeter. A capacitor attaches from the tweeter to the speakers. It limits itself from dipping too low, which is one of the primary reasons they blow in the first place. Many tweeters come with a power cable with yellow labels to indicate the capacitor’s location. Keep your hertz within the tweeter’s recommended frequency. Every tweeter should have a guide that shows its limitations. According to Everything What, tweeters typically have a range of 2,000 to 20,000 hertz. Going too high above or far below these limitations can cause all sorts of issues. Don’t turn your speakers louder than they’re supposed to go. When your speakers get too loud, it can cause damage to your subwoofers and tweeters. Many high-end tweeters can produce excellent sound without showing signs of damage, but that doesn’t mean they’re safe from harm. Consider installing a two-way crossover. These tools are designed with an inlet and outlet to protect your devices from going out of their respective ranges. Much like a capacitor, you can install it on a tweeter. Many people believe two-way crossovers are better than capacitors because they provide a better audio transfer. Getting a bigger amp will increase the headroom (but pay close attention). A few additional dB can provide excellent padding, but ensure you don’t use the headroom as an extra audio range. If they go up to 12 dB, you don’t have to play your music that high! Keep it a couple of dB below to provide headroom.
Save yourself time, money, and stress by applying our five-step rule to keep your tweeters in good condition. It might be tempting to blast them as high and loud as possible, but it’s not worth the struggles you’ll likely encounter.
Check their limits, keep the volume at a reasonable level, and consider hooking up a capacitor or two-way crossover. PricedRight Sales offers a beginner-friendly tutorial regarding blown tweeters that you can review here:
How To Check if Your Tweeters Are Blown
Are your speakers crackly or not producing the sound they used to? Are you worried if your tweeters and subwoofers are blown?
Fortunately, there are a few things you can do to check their condition. Throughout this process, ensure you don’t turn the speakers too loud since it can cloud the results or cause more damage.
So, how can you know if your tweeters are blown?
Test Your Tweeters With High Frequencies
You can find YouTube videos (or use your favorite songs) to test the high-end range. If you don’t hear anything or it sounds distorted, your tweeters are either permanently or partially damaged.
Crackling, ticking, or fogginess are signs of a damaged tweeter that might need to be replaced. If you’re unsure, we recommend taking your speakers to a music shop for a professional opinion.
Find Their Low Range
Much like the previous suggestion, it’s a good idea to check your tweeter’s low-end range. Find a song that reaches toward the bottom of their 2,000-hertz limit (or whatever your speakers are designed for), lower the volume, and listen to the clarity.
If it sounds smooth and similar to the rest of the audio clip, they’re fine. If it’s silent or distorted, your tweeters need to be replaced or repaired.
Compare the Tweeter’s Volume and Clarity
Does the high-end of your speakers sound similar to the low-end? They should have similar clarity and depth. Turn them to a quiet volume, listen closely, turn up the volume, and check if they’re consistent. Loud volume can highlight the tweeters, so it’s crucial to check as wide a noise range as possible.
If you’re noticing any audio problems with high frequencies, there’s a high chance your tweeters are involved. Testing their low and high-end range can let you know if they need to be fixed or replaced (or if there’s nothing wrong with them at all).
Conclusion
Tweeters aren’t supposed to drop to a low frequency, so it’s important to use crossovers and capacities whenever necessary.
The best way to treat the problem is to get an amplifier with enough headroom so the dB doesn’t dip below the recommended range.
Compression and clipping play a significant role in the process, but nothing overshadows the frequency.
AV Tip: How to Avoid Blowing Out Your Speakers
The bit rate has nothing to do with possible damage to amps or speakers. Modern music is unfortunately mastered to very high average levels: -12 dB or even greater is not uncommon and I have a Barenaked Ladies CD where the average level is -8 dB!. When a WAV file (1,411 kbps) is converted to a lossy format, it often introduces clipping in the waveform. Whether the bit rate is 64 kbps or 320 kbps it is the excessive clipping coupled with the very high average level plus high volume (read power) that introduces the possibility, but not certainty, that speaker damage may occur.
tcarcio posts on June 04, 2014 12:50
I am of the opinion that if you set things up correctly and don’t overdrive your speakers you can run amps or recievers that have more power than your speakers are rated for and have no problems. I have run my setup for years with more power then called for and over the past 30 years have only blown one tweeter and that was about 3 years ago on a set of B+W 801 series 80 that I believe had more to do with age than power. My first pair of decent speakers were a set of Henry Kloss towers that I ran for years with 300w amps. I asked at the time I bought them how much power they could handle and was told it really wasn’t an issue as long as I took care and didn’t abuse them. Now I am not saying I am right and someone else is wrong but I have said before if you run your system correctly and keep your drunk nieghbor away from the volume control you should not have a problem, IMHO.
Why Do Tweeters Blow When Amplifiers Distort?
Elliott Sound Products Why Do Tweeters Blow When Amplifiers Distort?
Why Do Tweeters Blow When Amplifiers Distort?
© 2001 – Rod Elliott (ESP)
Page Updated August 2021
Top
A vexing question, regularly asked and rarely answered properly – Why Do Tweeters Blow When Amplifiers Distort? The answers are actually quite simple, but the common misconception is that the distortion creates harmonics, and the additional harmonic content destroys the tweeter.
Not really – woofers and midrange drivers can also blow from a distorted amp, and this is unlikely to have anything to do with harmonics. Certainly, there are additional harmonics generated, and they will be at relatively high levels, but usually not high enough to cause more than relatively minor stress to the tweeters (in particular). It’s generally safe to assume that the harmonics generated will produce more power in the tweeter, but as shown below this is only a part of the story. Also, note that simulations (as you may see elsewhere) using a single tone or perhaps a pair of tones will not show reality. Music is a complex mix of many tones/ frequencies at once, and simple analysis using one or two tones will only lead you to a false conclusion.
It is also worth looking at the article Amplifier Clipping, as this provides some additional information that is not covered below. Although it usually does not affect tweeters, the effects on low frequency drivers can be very harmful.
Because of the nature of music and the over-use of compression, it is not only tweeters that are at risk. Woofers can also be damaged, due simply to excessive continuous power. In the end, it doesn’t matter if the signal to the speaker is clipped or not – if you feed excessive power into a loudspeaker, it will fail.
Tweeters can (and do) fail in biamped or multi-amped systems with electronic crossovers – even if the tweeter amplifier never clips. If the tweeter amp has enough power and the level is increased too far, the tweeter or compression horn driver will fail, even though there are no additional harmonics present. The issue is (and always was) excessive power and the increase in level below the nominal crossover frequency. How this comes about varies widely, but you can’t simply blame additional harmonics and pretend you’ve explained the problem !
Note that this article has been substantially changed (twice now). The conclusions are the same as the original, but new graphics have been added to show the waveform and an FFT of the tweeter signal under three different drive conditions. Hopefully the new information will make the article clearer, and the new simulations show the fundamental and harmonics so you can see the relative effects of clipping induced compression and harmonic generation. While the latter is certainly a contributor to the total power, its influence is far less than you may have expected.
A great part of the mystery is uncovered when we look at two aspects of music – the average versus peak power, and the energy distribution of typical music material.
It is commonly accepted (and quite valid) that music has a peak to average ratio of about 10-20dB. This means that if the signal is being amplified by a typical 100W amplifier, the amp’s power rating limits the absolute maximum power to 100W (give or take a little). Since this is the peak, the average must be somewhat lower, and we will assume 10dB for the sake of convenience. Average power is therefore 10W or less at the onset of clipping. This is something that I’ve verified as being fairly accurate, particularly with ‘contemporary/ modern’ music. Orchestral works will (or should) have a greater dynamic range, but assuming 10dB is ‘safe’.
This is not dynamic range per se, but it is most certainly a part of the overall dynamic range of the music signal. The term ‘dynamic range’ usually refers to the very quietest up to the very loudest passages in a given piece of music. In some cases, there is no variation whatsoever – it starts loud, is loud in the middle, and (just to be different) finishes … loud. The peak to average ratio may also be compressed, but it is difficult to reduce it to much less than 10dB without it becoming flat and lifeless. If done incorrectly, it can simply become a jumbled mess with no intelligibility whatsoever (and no, I’m not going to take this to its logical conclusion and denounce various styles that may be classified as music by only a select few ).
Most speakers are rated for a continuous power and an instantaneous power – the voice coil and to a lesser degree the suspension can withstand short bursts at much higher powers without damage. This does not imply that such power will be reproduced cleanly, and it will almost certainly be with a large increase in speaker distortion. The peak power rating defines the maximum transient power the loudspeaker can handle without suffering electrical or mechanical (stress induced) damage.
Nearly all tweeters are rated to ‘system power’, and this will usually be quoted relative to a specific crossover frequency. A hypothetical tweeter may be rated at 100W system power when crossed over at 3,000Hz. The power that it can withstand is not 100W! Not at any frequency or for any duration. The actual bandwidth-limited long-term average power for most tweeters is around 10W, but many can’t even handle that much without some distress.
Figure 1 – Power Distribution Chart
The above power distribution table is approximate (as must be the case), and applies for ‘typical’ music – whatever that may be. If we look at the case for a crossover frequency of 3kHz, we can see that 85% of the power is in the low frequency spectrum, and only 15% in the high frequencies above 3kHz. It is not difficult to deduce from this that the peak power to the tweeter will be in the order of 15W at full power from the amplifier, with the average hovering around 1.5 watts.
This is the way the system was designed to be used, and as long as the power amp does not clip, all is well (well, almost – read on).
When an amplifier is overdriven, the sound becomes distorted. This manifests itself in many ways, but the two we are interested in are the generation of harmonics, and the reduction of dynamic range – both the true dynamic range and the peak to average ratio. Let’s assume that the amp is overdriven by a mere 3dB, so the average level is now 20W, and the peaks are clipping. With many systems (or listeners), this will be virtually inaudible. Careful listening will uncover the fact that there is distortion present, and there is a definite reduction of intelligibility.
The speakers – both tweeters and woofers, are now being asked to absorb twice the power that would be normally obtainable, and the power is more constant – the signal is compressed by the power amp. Add to this the additional harmonics generated by the clipping waveform, and the tweeter may actually be getting up to 3 times the continuous power that was available before clipping. Peak power remains the same, since it is limited by the amplifier’s power supply voltage.
Now, let’s overdrive the amp by 10dB. The amp is delivering in excess of 100W, since it is reproducing square waves much of the time. The woofer will be subjected to perhaps a continuous 100W of power, and around 15W continuous will be available to the poor tweeter. Of this, probably less than 1% will be converted into sound (1% represents an efficiency of about 92dB/W/m). Ferrofluid helps, but virtually no hi-fi tweeter can withstand that sort of continuous power for any duration.
The tweeter was never designed for that! Just look at a 10W wirewound resistor for example. It is big and chunky, and made from a ceramic material that is designed to handle a lot of heat. Run one at 10W to find out just how much heat you will get. There is very little airflow around the tweeter voice coil, and the heat has nowhere to go. The result is that the voice coil will quickly overheat, and the adhesive that bonds the coil to its former, the former itself, and even the enamel insulation on the coil will be damaged. The result (naturally) is a dead tweeter.
As for the woofer – unless it is designed to take 100W or more continuous sinewave power, it will also overheat and eventually die. It takes a lot longer, because there is airflow around the voice coil, and the coil is bigger and has greater thermal inertia, but die it must if the abuse is maintained.
The following diagrams illustrate the above. The waveforms below are the result of simulation, but ‘real life’ will show exactly the same things as described. The waveform used for the simulation was made up from the following signals …
Frequency, Hz Peak Amplitude (V) Relative Amplitude (dB) 160 10 0 400 10 0 1 k 8 -2.0 2 k 7 -3.1 3.5 k 6 -4.4 5 k 5 -6.0 9 k 3 -10.5 13 k 2 -14.0 Table 1 – Test signal Composition
This waveform is not an attempt to reproduce any musical instrument or section of music – it is simply a batch of frequencies that make up a suitably interesting waveform. Of great importance is the ability to use this signal to demonstrate how the relative levels at various frequencies are affected by clipping. The peak to average ratio of the signal used is around 8.56dB. As noted above, this is (typically) about what we can expect with music, and because no frequency is below 160Hz it is realistic for a mid+high system used with a separate subwoofer. Unfortunately, it is simply not possible to cover all possibilities, but I believe that the test waveform used is sufficiently realistic to provide a useful result.
The signal (both normal and clipped) was passed through a passive 12dB/octave Linkwitz-Riley crossover network set at 3kHz. This was done so it’s typical of the results seen with a conventional passive speaker network. Lower order passive filters and/or lower crossover frequencies will make the situation worse.
Figure 2.1 – Signal Generator, Amplifier & Crossover
The simulated amplifier and crossover used for the following charts and graphs is shown above. It has a supply voltage of ±30V, with a nominal rating of 56W into 8 ohms. This was selected for convenience as much as anything else, but the results are no different with real amplifiers – regardless of power. Once the amp clips, more power is available to both the woofer and tweeter, and surprisingly little of the extra is the result of harmonics (often claimed to be the reason that tweeters fail). The crossovers are set for optimum accuracy, and the speaker loads are assumed to be purely resistive.
The first set of graphs was with the amp’s gain set so that the system was right to the maximum voltage swing, but with no clipping. Total amp output was measured at 11.2V RMS, and the peak to average (RMS) voltage ratio is 8.56dB. The gain was then increased by ~6dB (actually 5.38dB) for the ‘slight clipping’ example, and a further ~6dB (5.68dB, or 11dB total) for ‘moderate clipping’. The ‘odd’ gain increments are due to a simplified feedback network (R fb1 and R fb2 ).
Figure 2.2 – Normal Signal, Without Clipping
This shows the waveform at a level just below clipping. The red trace is the full range signal, green is the signal to the tweeter, and blue is the woofer signal. Notice that the tweeter signal is continuous – there are no breaks or discontinuities. This is important as we shall see from the next waveforms.
Figure 2.3 – Full Range Spectrum, Without Clipping
The above shows the spectrum of the composite waveform, with the amplifier voltage set at just below the onset of clipping. This is the reference, and the spectrum simply shows each frequency at its preset level. The RMS voltage of the tweeter signal is 3.7V, compared to 11.2V (RMS) for the total signal before the crossover.
Figure 2.4 – Tweeter Spectrum, Without Clipping
Figure 2.4 shows the spectrum of the signal presented to the tweeter. As you can see, it reflects the respective levels, with the low frequencies suitably attenuated by the crossover network.
The clipping is visible, and the peak amplitude has increased. The overall spectrum shows that the background energy level (i.e. any frequency that was not part of the input) has risen from around 10mV to an average of about 100mV below 20kHz. This is relatively insignificant, but also note that the peak levels of the input signals are also greater than the previous case.
Figure 3.1 – Slight Clipping
Of particular concern are those frequencies below the crossover point (3kHz) – 400Hz, 1kHz and 2kHz peaks are noticeably higher than in the previous graph – a clear sign of impending danger. Overall level to the tweeter has increased from 3.7V to 6.4V.
Figure 3.2 – Tweeter Spectrum, Slight Clipping
The spectrum overall shows that the average level of the signal and harmonics has increased as described above. At this level, there is some degradation of sound quality, but it could easily be missed during casual listening.
The tweeter voltage is now 6.4V RMS, and the total signal measures 19.3V. This means that the total signal voltage has increased by 4.7dB, and the tweeter signal level has increased by 4.76dB.
Increasing the gain further (another 6dB), the waveform is now visibly distorted, and if you look at the green trace (the tweeter) you can see that there are very noticeable ‘dropouts’. When the overall signal clips, sections of high frequency signal are simply lost, and replaced by harmonics of the clipped waveform. These harmonics do not replace (musically speaking) the frequencies that were removed by clipping.
Figure 4.1 – Moderate Clipping
The relative amplitudes of the tweeter signal and the full range signal show us that while the tweeter voltage has increased to 8.9V, the overall is now 24.7V. This is an increase of 7.6dB for the tweeter, and 6.9dB for the overall signal (compared to the unclipped waveform).
Figure 4.2 – Tweeter Spectrum, Moderate Clipping
The overall level is now much greater than before – it has risen quite dramatically over the entire spectrum. Not only are the wanted frequencies at a higher level, but so are the harmonics of the lower (clipped) frequencies. However, the background ‘noise’ of the harmonics is still more than 10dB below the peaks, so the contribution from harmonics is not great.
What we do see is the increase of signal level to the tweeter, with the moderate clipping example showing a 7.6dB increase. Remember that this translates to an average power increase of over 5 times to the tweeter. If the tweeter would normally be expected to handle a peak power of 15W and an average power of perhaps 5W (based on Figure 1 and a 100W amplifier), a 7dB increase will take that average to 25W! The tweeter will not survive.
The above examples represent a total gain increase of 12dB from the non-clipping condition to the moderate clipping states. As the gain is increased further, the ‘power compression’ effect described becomes worse. At no time does the additional energy of the harmonics created by clipping exceed a level of more than around -7dB with respect to the fundamental frequencies – unless one goes absolutely berserk and forces the amplifier into total square-wave clipping. That will occur with 20dB of excess gain (i.e. 20dB above the clipping level, based on the waveform described above).
With the volume advanced by 12dB above clipping, the average power is well above danger level. The distortion will be highly audible with most music, but is not at all uncommon. Parties are probably the worst offenders, although I have heard many high power (10kW or more) PA systems driven to at least this level of distortion.
Bear in mind that most ‘ordinary’ (non-audiophile) people will not be aware that there is anything wrong at this point! During ‘festivities’ (for want of a better term), liberal quantities of alcohol enriched fluids will ensure that ears remain unresponsive to the assault. Given the number of times I have heard about peoples’ speakers ‘blowing up’ during (or after – allegedly) a party, we can safely conclude that the requirement for more noise is far greater than any need for fidelity.
Few tweeters will last long with sustained power at a level easily achieved with an overdriven 100W amplifier – they are simply not designed for it. Midrange speakers and woofers will probably be pushed beyond their limits as well. Remember too, that not only is the ‘in band’ signal increased, but so is the out of band signal. The tweeter must also handle many times the normal power at all frequencies below the crossover frequency. This alone can cause damage, without the heating effects of such a high sustained power level.
Is the last example extreme? Not at all – I have actually understated the reality. When any system is driven so hard that the distortion is obvious to even untrained ears, it is reproducing close to square waves much of the time. A 100W amplifier driven to full power with a square wave will produce 200W, and when driven into heavy clipping with a music signal can easily achieve well over 100W average continuous power.
Conclusion? —- Exit tweeters (and/or midrange drivers and/or woofers).
The term ‘power compression’ is used here to describe the way that the power level is increased as an amplifier clips. Although it is covered above, the original drawings I used showed the effect, although I was never very happy with the drawings themselves. The new images are a capture from an FM radio that I have connected to my PC, and hopefully show the effects better than before.
Figure 5 – Original Full Bandwidth Signal – No Clipping
Figure 5 shows the captured signal, and the red line indicates the clipping level. The signal shown was captured over about 20 seconds, and as you can see, the signal never reaches the red line. The average can be determined roughly by eye, and it’s just above 0.3 on the scale (blue line). Since the chart shows voltage, that’s roughly one tenth power, or 10W for a 100W amp. Assuming a peak-average ratio of around 10dB is generally fairly close, so a 100W amp will deliver around 10W average power with ‘typical’ music (assuming such a thing exists ).
Figure 6 – Full Bandwidth Signal – Heavy Clipping
Advancing the volume control by only 6dB (double the voltage gain) pushes nearly all peaks beyond the red line (representing the amp’s maximum power), so the signal clips heavily. The average power is now around 0.7 on the scale – this is the half power point (3dB below maximum power), so the average is now 50W for the same 100W amplifier. This means that the power delivered to the woofer is ×5, and power to the tweeter is a little more than that because of the additional harmonics.
Figure 7 – Full Bandwidth Signal – Severe Clipping
A further 6dB gain increase is very bad news indeed. The average voltage is at least 0.9 on the scale, and that means that the average power is a minimum of 80W. Because the signal is clipped so badly, there will be times when the output power will be well over 100W. To understand this, remember that a squarewave has double the power of a sinewave, so a 100W (sinewave) amplifier can deliver 200W with a full-power squarewave signal.
With this much clipping, the tweeter will be subjected to far more continuous power than it was ever designed for. As in the previous example, it will not survive.
These last three diagrams are another way of showing exactly the same thing as described with the example power waveforms, but over a longer period of time. The result is the same in either case (since they describe the same thing). All loudspeaker drivers in your system are at risk, and the tweeter (being the most fragile) is usually the first to go.
As for claims that a bigger amplifier won’t clip, so won’t blow your speakers – be very careful! Remember that I have covered clipping at 10dB (or a little more) above the amplifier power, and although highly undesirable, it does happen. 10dB above 100W is 1kW! Will your speakers survive being driven with peak power of 1kW? The answer (of course) is “no!”
All the above is valid when an amp clips, but what about speaker drivers that blow for no apparent reason, and with no clipping at all? Well, the people who create the final mix for CD (and those who actually transfer the final mastered tracks to CD format) have been using compressors for a long time – almost as long as music has been transferred to mass media in fact. What is different now, is that many of them seem to use their compressors with increasing vigour. The result is music that is compressed so heavily that the 10dB peak to average ratio we used in earlier examples no longer applies. Each individual recorded track is compressed, the final mix is compressed, and it may be compressed yet again before it is transferred to CD. For reasons that I cannot fathom, it seems that every new CD that is released has to be ‘hotter’ (louder) than the last. Guess what people – there is a limit, and we reached it long ago !
Towards this end (and to make matters worse), you will find some CDs that are pre-clipped, with the peaks of the occasional loud signal neatly cut off at the top and bottom. With a peak to average ratio of perhaps 6dB in the worst cases, we need to examine the effects on the loudspeaker drivers.
Using the same 100W amp as above, it was already established that the average power would be around 10W at the onset of clipping. Although this is not a trivial amount of heat, most speakers will be able to dissipate it without too much difficulty. As the peak to average ratio is reduced by compression, the effect is exactly the same as clipping the amp, except we don’t get the harsh distortion.
With a 6dB peak to average ratio, the poor loudspeaker now has to cope with an average power of 50W as the peaks reach clipping level. Unless you are dealing with serious professional drivers that are designed for continuous high power, 50W is a lot of heat to dispose of. Should you be using a 200W amp, that increases to 100W – continuous! If you think 100W is trivial, try holding a 100W resistor that is dissipating its rated power. Actually, don’t! You will burn yourself quite badly. Remember that over 99% of all power that goes into a domestic loudspeaker is dissipated as heat, with less than 1% being converted into sound.
As you can imagine, it is entirely possible to destroy drivers without ever letting the amp clip. Speaker systems rated for 200-500W almost always refer to peak power, and the average (or continuous) power rating is in reality as little as 10% of that claimed. This is perfectly alright for most people in a domestic environment, where very high SPL isn’t needed. If you like to listen really loud, then you will almost certainly have problems with drivers failing. Perhaps the loudspeaker manufacturers haven’t quite got the message that a great deal of music is compressed much harder than they anticipated.
The above applies to tweeters, midrange drivers and woofers equally – all can be damaged by excessive sustained power. Regardless of claims, there are actually few loudspeakers that can withstand 100W of continuous average power for any length of time. To be able to do so requires large diameter voicecoils (preferably with aluminium formers to aid heat removal), vented pole-pieces, finned magnet assemblies and somewhere for the heat to go – preferably not just into the cabinet where it can’t escape. This is not a trivial exercise, and professional drivers that can withstand that sort of abuse are very expensive indeed.
Finally, the CD (and other digital formats) allow the recording engineer/ producer to have as much bass as they want, plus some more for good measure. This can extend to very low frequencies – below audibility in fact. Tuned (vented) loudspeaker enclosures (usually) provide better bass extension than sealed types, but if there is any material recorded (and amplified) that is below the box tuning frequency, this will cause massive woofer cone excursion because the rear of the cone is unloaded below the vent tuning frequency. You won’t hear the deep bass, but the cones will move very energetically indeed, and can easily reach physical excursion limits. Loudspeaker damage is guaranteed if this is done at high power levels, and can include buckled and/or detached voicecoils, broken lead-in wires and torn suspensions.
A persistent myth in the audio industry is that clipping damages tweeters, so you should use a bigger amp to ensure more headroom so the amp won’t clip. This claim is simply bollocks! Take the 100W amp described above, and replace with an amp big enough to prevent clipping … even with the additional 12dB input signal as shown in Figure 7. Since a 100W amp was just below clipping with an average output of 16W, if we add 12dB that takes the peak amp power to 1.6kW (near enough) and the average power will be 254W.
Do you imagine for an instant that this amp won’t blow the tweeters (and everything else) if the output level is increased by 12dB (until it’s just below clipping)? Everything will fail, and usually fairly quickly if the speaker was designed for a ‘nominal’ 100W input. It is simply nonsense to imagine that the loudspeaker drivers in a 100W speaker can survive an average power of over 250W and peak power of up to 1.6kW.
If a user often turns their amp up to beyond clipping levels, they will probably do the same with a bigger amp. They might even turn it up more, because it won’t have the distortion component which increases apparent loudness until the average power is a great deal higher. Such users will never hear signs of speaker distress if they can’t even hear gross clipping. Speaker failure is a certainty, even if their 1.6kW amp only ever clips a few transients. They can expect the tweeter to fail, and the woofer to catch on fire.
So, while it’s perfectly alright to allow perhaps 3-6dB or so of headroom for the power amps, that relies on that fact that it is reserved as headroom! If you use the extra power then there’s no headroom any more, and all the effects explained will still happen, but at even higher power levels than described above.
Headroom implies that there is extra power for the occasional transient. If you use the extra power, you no longer have any ‘headroom’!
Copyright Notice. This article, including but not limited to all text and diagrams, is the intellectual property of Rod Elliott, and is © 2001-2006. Reproduction or re-publication by any means whatsoever, whether electronic, mechanical or electro- mechanical, is strictly prohibited under International Copyright laws. The author (Rod Elliott) grants the reader the right to use this information for personal use only, and further allows that one (1) copy may be made for reference. Commercial use is prohibited without express written authorisation from Rod Elliott.
Page created and copyright © 28 Jul 2001./ Updated 15 Aug 2006./ Updated 09 Jun 2012 – replaced spectrum and waveform images, improved power compression images for clarity./ Jun 2015 – added Section 6. Aug 2021 – Added Figure 2.1 (test setup).
So you have finished reading the how to protect tweeters from blowing topic article, if you find this article useful, please share it. Thank you very much. See more: tweeter capacitor, how to install a resistor on a tweeter, tweeter crossover, how to install tweeters to amp, how to fix a blown speaker, how to adjust crossover on component speakers, how to avoid blowing out car speakers, how to put capacitor on tweeter