You are looking for information, articles, knowledge about the topic nail salons open on sunday near me how to prime my intex pool pump on Google, you do not find the information you need! Here are the best content compiled and compiled by the https://chewathai27.com team, along with other related topics such as: how to prime my intex pool pump how to prime a summer waves pool pump, how to prime a pool pump hayward, how to prime pool pump, can’t get pool pump to prime, how long does it take to prime a pool pump, how to prime intex sand filter pump, how to prime a pool pump with sand filter, how to prime pool pump with cartridge filter
- Turn off the pool pump.
- Select either “recirculate” or “filter” on the multiport valve. Move the multiport valve or handle to recirculate. …
- Fill the Pump with Water. Before opening the lid, release the pressure in the pool filter. …
- Refit the Lid and Switch on the Pump.
- Turn pump off.
- Turn Cell off.
- Turn Filter handle to Re-Circulate (assuming you have a sand filter).
- Remove skimmer basket. …
- Take the pump lid off and pour 4-5 buckets of water into the pump basket. …
- Repeat Step 5 a few times, if necessary.
Contents
How do I manually Prime my pool pump?
- Turn pump off.
- Turn Cell off.
- Turn Filter handle to Re-Circulate (assuming you have a sand filter).
- Remove skimmer basket. …
- Take the pump lid off and pour 4-5 buckets of water into the pump basket. …
- Repeat Step 5 a few times, if necessary.
How long does it take a pool pump to prime?
Prime the pump at the beginning of each pool season.
When you prime the pump, you add water to it and bleed off the air in the lines. Prime your pump anytime your pool sits for 1-2 months.
Are pool pumps self-priming?
Many pool pumps nowadays are self-priming, meaning that they can automatically generate water flow after turning on, even if there are significant amounts of air in the system. Some pumps require you to manually prime your pump before turning it on.
How do I remove the air from my pool pump?
- Turn off power to the pool pump and pool heater. …
- Rotate the air relief valve located on top of the filter canister counterclockwise to open the valve.
- Close the skimmer valves and leave open the main drain valve.
Why is my pool pump full of air?
It’s likely happening because of one of these issues: The pool water level is too low. The strainer pot lid isn’t on tight or its O-ring is loose/absent/compromised. The union between the valves and the pump isn’t tight or its O-ring is loose/absent/compromised.
How much water do you need to prime a pool pump?
Using a garden hose, fill the basket up with water for at least two full minutes. While leading to the skimmer, this water will push air out from the pipes and create suction back into the pump. Once the basket is about 80% full—up to the outlet called the intake port—you’ll know the system is air free.
How much water do you need to prime a pool pump?
Using a garden hose, fill the basket up with water for at least two full minutes. While leading to the skimmer, this water will push air out from the pipes and create suction back into the pump. Once the basket is about 80% full—up to the outlet called the intake port—you’ll know the system is air free.
Why is my pool pump not pulling water?
It could be something blocking it, a dirty pool filter, or too much air in the system. If there’s something blocking your pump’s suction, check your filter gauge. If it’s 10psi above the normal reading, clean your filter. This will reduce pressure and reset your pump’s flow.
Why does my pool pump lose its prime?
Debris blocking the suction strainer or foot valve is the most common cause. A blockage in the intake line can cause the water in the pump casing to overheat and literally boil out of the casing causing the pump to lose prime.
How to Prime a Pool Pump (Above Ground & Inground Pool)
- Article author: www.myperfectpool.com.au
- Reviews from users: 3671
Ratings - Top rated: 3.3
- Lowest rated: 1
- Summary of article content: Articles about How to Prime a Pool Pump (Above Ground & Inground Pool) Updating …
- Most searched keywords: Whether you are looking for How to Prime a Pool Pump (Above Ground & Inground Pool) Updating If you’re not sure how to prime your pool’s pump or your pool pump is losing its prime or won’t keep prime, you’re in the right place.
- Table of Contents:
How to Prime a Pool Pump
When Should You Prime Your Pool Pump
Why Pool Pump Loses Prime or Won’t Prime And How to Fix
How Long Does it Take to Prime a Pool Pump
Is Bleeding a Pool Pump the Same as Priming
How Remove Air Out of Pool Pump
Tips for Priming Above Ground Pool Pumps
Tips for Priming Intex Summer Waves and Bestway Pool Pumps
Conclusion
Legal Information
How to PRIME a Swimming POOL PUMP | Swim University – YouTube
- Article author: www.youtube.com
- Reviews from users: 46236 Ratings
- Top rated: 4.2
- Lowest rated: 1
- Summary of article content: Articles about How to PRIME a Swimming POOL PUMP | Swim University – YouTube Updating …
- Most searched keywords: Whether you are looking for How to PRIME a Swimming POOL PUMP | Swim University – YouTube Updating When your pump is not drawing any pool water, it means it needs to be primed. Priming is the act of adding water to the filter system to kickstart it. Matt g…pool pump, pool maintenance, swimming pool, pool care, pool cleaning, pool chemicals, above ground pool, intex pool, swimming pool maintenance, swimming pool care, how to clean a swimming pool, swimming pools, salt water pool, above ground pool maintenance, maintaining a pool, pool maintenance for beginners, inground pool, pool pump problems, pool pump wont prime, pump priming, prime pool pump, priming a pool pump, pool not priming, pool pump tips, pool pump not priming
- Table of Contents:
Pool Tips: How to prime your pool pump | Active Pool Supplies
- Article author: www.activepools.com.au
- Reviews from users: 23028 Ratings
- Top rated: 4.3
- Lowest rated: 1
- Summary of article content: Articles about Pool Tips: How to prime your pool pump | Active Pool Supplies Updating …
- Most searched keywords: Whether you are looking for Pool Tips: How to prime your pool pump | Active Pool Supplies Updating We are all too familiar with the sound of a pool pump that is struggling for water or the drama of r
- Table of Contents:
Other Tips & Advice
Talk to the pool experts
How To Bleed Air From A Pool Filter – YouTube
- Article author: www.youtube.com
- Reviews from users: 27379 Ratings
- Top rated: 3.0
- Lowest rated: 1
- Summary of article content: Articles about How To Bleed Air From A Pool Filter – YouTube Updating …
- Most searched keywords: Whether you are looking for How To Bleed Air From A Pool Filter – YouTube Updating How To Bleed Air From A Pool FilterBleeding air out of your pool filter is one of the most important things you can do to keep your system perfectly working….video, chia sẻ, điện thoại có máy ảnh, điện thoại quay video, miễn phí, tải lên
- Table of Contents:
How To: Prime a Pool Pump – YouTube
- Article author: www.youtube.com
- Reviews from users: 33498 Ratings
- Top rated: 5.0
- Lowest rated: 1
- Summary of article content: Articles about How To: Prime a Pool Pump – YouTube Updating …
- Most searched keywords: Whether you are looking for How To: Prime a Pool Pump – YouTube Updating How To Prime A Pool Pump – http://bit.ly/36mZDpfHow To Determine Why a Pool Pump Won’t Prime – http://bit.ly/30JyqvOHow To Clean Out a Pool Pump Impeller – h…how to, pool pump, swimming pool, inyo, pools, diy, tips, tricks, maintenance, pool care, pool maintenance, swimming, pool, water, repair, fix, help, prime, pump, motor, pressure, low, system, swimming pool repair, how to prime a pool pump, prime a pool pump, priming a pool pump, pool pump wont prime, pool pump problems, swimming pool problems
- Table of Contents:
How to Prime an Above-Ground Pool Pump | DoItYourself.com
- Article author: www.doityourself.com
- Reviews from users: 42485 Ratings
- Top rated: 3.0
- Lowest rated: 1
- Summary of article content: Articles about How to Prime an Above-Ground Pool Pump | DoItYourself.com
Switch on the pump, then open one suction se valve very slowly. Within a minute, the pump should be able to catch its prime and get the water … … - Most searched keywords: Whether you are looking for How to Prime an Above-Ground Pool Pump | DoItYourself.com
Switch on the pump, then open one suction se valve very slowly. Within a minute, the pump should be able to catch its prime and get the water … When an above ground pool pump isn’t circulating water with effective force, you might need to prime the pump. - Table of Contents:
Step 1 – Get the Pool Pump Ready
Step 2 – Close the Valves
Step 3 – Inspect and Clean the Strainer Basket
Step 4 – Fill the Strainer
Step 5 – Run Water Through the Pump
Step 6 – Add All the Lines
Attention Required! | Cloudflare
- Article author: blog.thepoolfactory.com
- Reviews from users: 43740 Ratings
- Top rated: 3.4
- Lowest rated: 1
- Summary of article content: Articles about Attention Required! | Cloudflare Another way air can enter your pool filter system is through the strainer housing. Turn off the pump and then slowly open the l to allow air escape from the … …
- Most searched keywords: Whether you are looking for Attention Required! | Cloudflare Another way air can enter your pool filter system is through the strainer housing. Turn off the pump and then slowly open the l to allow air escape from the …
- Table of Contents:
Please complete the security check to access blogthepoolfactorycom
Why do I have to complete a CAPTCHA
What can I do to prevent this in the future
How to Prime a Pool Pump in 4 Easy Steps
- Article author: www.swimuniversity.com
- Reviews from users: 24427 Ratings
- Top rated: 3.5
- Lowest rated: 1
- Summary of article content: Articles about How to Prime a Pool Pump in 4 Easy Steps 1. Turn the Multiport Valve to Recirculate · 2. Remove Pool Plugs · 3. Fill The Pump With Water · 4. Turn the Pump On. …
- Most searched keywords: Whether you are looking for How to Prime a Pool Pump in 4 Easy Steps 1. Turn the Multiport Valve to Recirculate · 2. Remove Pool Plugs · 3. Fill The Pump With Water · 4. Turn the Pump On. A lot of things can happen to keep a pump from working properly, but a lot of those things can be avoided by knowing how to prime a pool pump.
- Table of Contents:
Why Do I Need to Know How to Prime a Pool Pump
What is Priming a Pool Pump
How to Prime a Pool Pump
Pump Priming Troubleshooting
It’s Prime Time!
How to Prime a Pool Pump: Step-by-Step – Pool Research
- Article author: poolresearch.com
- Reviews from users: 15134 Ratings
- Top rated: 3.5
- Lowest rated: 1
- Summary of article content: Articles about How to Prime a Pool Pump: Step-by-Step – Pool Research Steps to Prime Your Pool Pump · Turn off the pump. · Switch to recirculate. · Release air. · Clean out the pump basket. · Fill the pump basket. · Once the pump basket … …
- Most searched keywords: Whether you are looking for How to Prime a Pool Pump: Step-by-Step – Pool Research Steps to Prime Your Pool Pump · Turn off the pump. · Switch to recirculate. · Release air. · Clean out the pump basket. · Fill the pump basket. · Once the pump basket … I walk you through how to prime your pool pump and why you should do it.
- Table of Contents:
How Pool Pumps Work
What Does it Mean to Prime a Pool Pump
Why You Should Prime Your Pool Pump
Steps to Prime Your Pool Pump
Troubleshooting Pool Pump Problems
The Takeaway on Priming Your Pool Pump
Free Pool Care Checklist
How to Prime Your Pool Pump in Just Five Steps – PoolPartsToGo
- Article author: poolpartstogo.com
- Reviews from users: 46270 Ratings
- Top rated: 5.0
- Lowest rated: 1
- Summary of article content: Articles about How to Prime Your Pool Pump in Just Five Steps – PoolPartsToGo
How to Prime Your Pool Pump in Just Five Steps · Step 1: Redirect the Water · Step 2: Prepare Your Pump · Step 3: Fill Your Pump with Water · Step 4 … … - Most searched keywords: Whether you are looking for How to Prime Your Pool Pump in Just Five Steps – PoolPartsToGo
How to Prime Your Pool Pump in Just Five Steps · Step 1: Redirect the Water · Step 2: Prepare Your Pump · Step 3: Fill Your Pump with Water · Step 4 … It’s simple: in order for a pump to work at its highest efficiency, it needs room in the pipes for water to flow freely. Is air currently infiltrating your system? Then it’s a good idea to get priming. With the help of these five easy steps you can prime your pump and have it working in no time. - Table of Contents:
Login to my account
Recover password
Create my account
Why Is It Even Necessary to Prime
Step 1 Redirect the Water
Step 2 Prepare Your Pump
Step 3 Fill Your Pump with Water
Step 4 Seal Your Pump Up and Turn the System Back On
Step 5 Stay Tuned
JOIN THE DEEP DIVE NEWSLETTER
See more articles in the same category here: 670+ tips for you.
How to Prime a Pool Pump (Above Ground & Inground Pool)
Share this…
Priming a pool pump is something every pool owner will need to do every now and again. If you’ve just opened the pool from winter, installed a new pool or a new piece of pool equipment or drained the pool, then you’ll have to prime the pump before starting it again.
Luckily, it’s an easy process. Make sure you keep reading to the end of the article as we have some common troubleshooting points for those of you having trouble priming your pool pumps.
How to Prime a Pool Pump
For a pool pump to run properly, there needs to be minimal air in it when running. When looking through the transparent pump lid you shouldn’t see large pockets or air or hear gurgling noises.
This process is the basic process for priming all pool pumps and filters and covers sand filters, DE filters, above-ground pool pumps and Intex, Summer Waves and Bestway pumps.
Here how to prime your pool pump:
priming pool pump
1. Turn off the pool pump
2. Select either “recirculate” or “filter” on the multiport valve.
Move the multiport valve or handle to recirculate. This will pass water directly into the pool pump and back into the pool. You can also use the “filter” setting.
It’s important to only change filter settings when the pool pump is switched off.
3. Fill the Pump with Water
Before opening the lid, release the pressure in the pool filter. You can do this by opening the pressure release valve or bleed valve. It’s usually located on the side or top of the filter. Close the valve again when all the air has stopped coming out of the valve.
With the pressure released from the filter, open up the pool pump lid. Whilst you have the pump open, empty the pump basket and clean all the debris from it.
Now take a garden hose or bucket of water and fill up the pump. You want to keep filling up the pump until the water is at the brim. You may find the water does down. Sometimes the water level in the pipes is low and this will happen. That’s OK, just keep filling until the pump overflows and the water level in the pipe remains at the top and doesn’t drain too quickly.
4. Refit the Lid and Switch on the Pump
Inspect the lid and the lid seal for damage before refitting it. Make sure the lid is seated correctly and is tight to prevent possible air leaks.
Switch the pump back on.
The pump will gurgle and make noises for 30 secs to a couple of minutes whilst it sucks the air out of the system. Run the pool pump to circulate water for several minutes. Keep watching the water in the pump lid and listen to the pump.
If you keep seeing large air bubbles in your pump, you could still have air in the system. See troubleshooting below for more details of what to do.
Now open the air relief or bleed valve on the filter housing until water flows out of it (20-40 secs), then close it again. This will release the air from the filter.
Tip: Always prime your pool pump after draining and refilling the pool to get rid of any air pockets. You’ll need to prime your pump if you’re opening your pool after a winter shutdown, too.
When Should You Prime Your Pool Pump
Your pump is designed to be full of water. Without sufficient water in it, it will not operate correctly and may burn out.
Here’s when you will need to prime your pool pump:
Anytime you open your pool’s system
Opening your pool after winter shut down
If the water level has gone below the skimmer
If you’ve replaced the pump or filter or repaired a pipe
After cleaning the pool filter
When restarting your pump, prime it first then check it has enough water in it. You can do this by looking in the pump’s transparent lid. If the water is not all the way to the top, open it up and reprime it by filling it up. If it is making gurgling noises or pulsating, try repriming it.
Don’t leave the water level low, as low water levels in your pump will mean excessive heat being generated. And this excessive heat will burn out the seals and bearings. If that happens, you’ll likely be up for a new pump.
Why Pool Pump Loses Prime or Won’t Prime. And How to Fix.
1. Reprime the Pump
If your pump won’t prime or loses prime the first thing you should try is repriming it. Sometimes the water level can be a little low in the pump which means the pump can’t create the required suction to start properly.
Open up the pump and keep filling it with water until the water overflows and does not go down again. Get the lid on fairly quickly and restart the system.
2. Low Water Level
Your pool pump draws water from the skimmer. If the pool’s water level is incorrect, this will introduce air into your pool pump and will cause pump priming issues. The skimmer has to have enough water in it so the pump is never starved for water, even when your kids are splashing around and doing bombs.
Make sure the water level is about halfway up the skimmer or a little bit higher. If the water level is low, fill up your pool with a garden hose. This will ensure the pump has enough water and doesn’t lose it’s prime. Reprime the pump after does this.
3. Clogged Up Skimmer
As mentioned above, the pump draws the water in from the skimmer. If the skimmer basket is full and blocked up, this will make it hard for the pump to freely suck the water into it.
With the pump switched off, empty out the skimmer basket. Make sure all the leaves and debris are removed then replace it.
clogged pool filter and skimmer
4. Clogged Up Pump Basket
A pump basket or strainer overfull with debris and leaves is enough to impede the flow of water. If the water flow is impeded, the pump will not be able to draw enough water fast enough to hold its prime.
To clean it, with the pump off, release the pressure in the pool filter, then open up the pump lid and clean out the debris.
5. Clogged Impeller
Sometimes leaves and debris can get past the pump basket and into the impeller. The impeller is the spinning part of the pump and draws the water through the pump. It kind of looks like a propeller of a boat.
To check this, with the pump switched off at the breaker, release the pressure in the pool filter. Now open up the pump and remove the pump basket. Reach into the pump and remove any debris in there.
6. Air Leaks in Suction Side
Having an air leak is another reason a pool pump won’t prime or hold prime. Air leaks occur on the “suction” side of the pump.
Air leaks occur on the suction side of the pool’s system and pump (highlighted in red color).
Start by making sure all the unions are seated correctly and are tight. Usually, leaks in pipes will occur at the corners and joins. You can undo the unions and check the o-rings and seals are in good condition too.
Another common reason for the pump losing prime is a broken or leaking pump lid. Open up the lid and check the rubber seal is in good condition. Also carefully check the lid for cracks. Replace the lid and rubber seal if they aren’t in good condition.
How Long Does it Take to Prime a Pool Pump
Priming a pool pump should only take a few minutes. Usually, the most time-consuming and difficult part of the job is taking the lid off the pool pump. If you have a stuck lid, we have some tips here: How to Undo a Stuck Pool Pump Lid Without Breaking It
After filling up the pump with water and starting it again, it should only take a couple of minutes to be properly primed. If the pump continually gurgles or it still has a lot of air in it, you should follow our guide:
How to Bleed the Air From Pool Lines
Is Bleeding a Pool Pump the Same as Priming?
Bleeding a pool pump is essentially the same thing as priming a pool pump. Bleeding is a term used, in many industries, to get the air out of something.
In this case, priming the pump is preparing it for use by adding water to it. The process of adding water to it removes most of the air. Having enough water in the pump is necessary to create enough suction to pump the water properly.
How Remove Air Out of Pool Pump
When a pool pump has air in it, it will not operate correctly. It may cavitate and in some extreme cases, it could overheat seizing up the bearings.
There are three methods to bleed air out of the pool pump:
The first one is to reprime the pool pump.
The second is to bleed the pool lines/pipes
The third is to let the pump fix itself by running it
1. Reprime the Pump
In many cases, if you have air in the pump you can fix the issue by repriming it. Simply switch it off, open up the pump lid and fill up the pump with water. It’s important to fill the pump up to the brim. It may take a bit of water if the water level in the pipes is low. With the lid fastened, switch the pump back on.
If your pool system is in good order, this should bleed the air out of your pump. But if it doesn’t there could be several reasons:
Pool water level below skimmer
Blocked up skimmer or pipe
Pump basket full of leaves
Air leak in system
We have a full article on air leaks here:
Air Bubbles In Pool Or Pump | Causes and Dangers
2. Bleed the Pool Pipes/Lines
If you have excessive air in your pool lines, the pump will have air in it. It may not prime or lose prime. Pool pumps need to be fully filled with water to operate correctly. Excessive air in the pool pipes means that the pump will not have sufficient water in it to keep its prime.
Bleeding the pool lines and pipes is simple. Start by shutting the valves to the main drain and close the other pool valves too. With the multiport valve set to the “filter” position, switch on the pump and then slowly open one valve at a time until the pump draws the air out of the pipes and out of the system.
We have a detailed article on the full process here:
How to Bleed the Air From Pool Lines
3. Leave the Pump to Run
A common hack to get air out of the pump is to let the pump run for a few minutes. The air might come out as the pump circulates water.
This works best for air pockets trapped after the pool pump was switched off. When you turn on the pool pump, the water circulates through the skimmer to the filter and back into the pool through the return jets.
If this doesn’t work, and you haven’t tried the above steps, try these steps before calling in a professional.
Tips for Priming Above Ground Pool Pumps
pool pump for above ground pool
If your above ground pool pump is not priming correctly or losing prime after following the above steps, check out these specific tips.
Priming above ground pool pumps is a little different from priming inground pools. Most of the time, the pump and filter are located level with the bottom of the pool, and so the water flows downhill from the pool into the pump making it mostly unnecessary to prime the pump.
If you’re having trouble keeping prime, try these things:
Make sure hoses are tight
Clean out skimmers and pump baskets
Replace or clean dirty cartridges
Tips for Priming Intex, Summer Waves and Bestway Pool Pumps
If your Intex, Summer Waves, or Bestway pool pump is losing prime or not pumping water properly, it’s usually a fairly easy fix.
Usually, Intex pool pumps such as the Krystal Clear series of cartridge filters and sand filters will not need priming most of the time. This is because Intex pumps and pool filters are most often installed level with the bottom of the pool, so the water will naturally flow down from the pool and into the pump.
Here’s some reasons why your Intex pool pump and filter will not prime:
Air in the system
A dirty filter
Clogged skimmer or pipes
Loose hoses or damaged hoses
Usually, the biggest culprit for Bestway, Summer Waves and Intex cartridge filter pumps not priming is a dirty filter or air in the system. The filters do not last long and clog quickly.
To fix this, simply replace the filter. To remove the air from the system, loosen the knob on the very top of the filter to let the air out. When you see water coming out, tighten it back up, you’ve now bled the air.
You can get replacement Intex cartridge filters here:
Replacement cartridge element for Intex filter.
Click here to check price >>
Conclusion
If you’ve been having issues priming your pool’s pump or just needed to know how to prime your pump, you should by now know enough to get your pump working again.
If after reading this article, you are still having trouble, it’s time to call a pool professional in to sort out the issue.
Happy swimming!
Pool Tips: How to prime your pool pump
10 February 2022
by Angus Donald
We are all too familiar with the sound of a pool pump that is struggling for water or the drama of refilling the system with water after servicing. Help is at hand.
If the pool water has drained out of the pipework from the pump back to the pool, it can sometimes be difficult for the pump to suck the water from the skimmer box back into the filtration system. This might be particularly relevant if your pump is a long way from the pool, or is positioned quite high above the level of the pool water.
Here’s a quick guide to priming your pump.
– Ensure the level of water in the pool is high enough to easily cover the skimmer.
– Ensure the unions on the pump & filter are tight and ensure Union O Rings have not been removed.
– Ensure the Pump Lid O Ring is present (lubricate with Silicon Grease not petroleum-based grease).
– Disconnect any Automatic Cleaner from the skimmer box.
Steps to prime the pump:
1. Turn pump off.
2. Turn Cell off.
3. Turn Filter handle to Re-Circulate (assuming you have a sand filter).
4. Remove skimmer basket. Take all nozzle & fittings off garden hose and place end of hose into the Suction Line (as far as it will go) in the skimmer box. Turn hose on full.
**DO NOT LEAVE FITTINGS ON HOSE AS THEY MAY GET SUCKED INTO, AND STUCK IN THE SUCTION LINE**
5. Take the pump lid off and pour 4-5 buckets of water into the pump basket. Replace lid quickly and turn pump on.
6. Repeat Step 5 a few times, if necessary.
Assuming the pump primes up, remove the garden hose and replace the skimmer basket.
Allow the pump to run for 5 minutes before turning off, then:
– Return Filter handle back to Filter,
– Turn Cell back on.
– Re-connect Auto Cleaner, if appropriate.
– Turn pump back on (set chlorinator to Auto, if appropriate).
If the pump still does not prime, or is noisier than normal, you will need to call us to book a Service Call.
How to Prime an Above-Ground Pool Pump
How to Prime an Above-Ground Pool Pump
To ensure our content is always up-to-date with current information, best practices, and professional advice, articles are routinely reviewed by industry experts with years of hands-on experience.
When an above-ground pool is unable to pump the water through it with force, its pump needs to be primed. This process pushes out any blockage within the system to restore efficient water flow.
The main source of obstruction is usually air bubbles. When a pump is primed, the air is purged so water can flow through. Follow these steps to prime an above-ground pool pump. It may be necessary to repeat them a few times, but stick with it. Without this process, the quality of your pool water will suffer.
Step 1 – Get the Pool Pump Ready
If the pump is running, switch it off. Unplug the electrical cord or turn off the circuit breaker so the power to the pump is disconnected.
Step 2 – Close the Valves
There are some valves on the suction of the pump, which are the main drain, skimmer and vacuum lines. Close all these valves. Locate the air relief valve on your filter, and open it to release any pressure that has built up inside the pump. Very slowly, open the strainer lid of the pump. If your above-ground pool pump does not have an air relief valve, use the strainer lid to release the pressure. Again, use caution! The built up pressure can be dangerous.
Step 3 – Inspect and Clean the Strainer Basket
The strainer basket of the pump sometimes gets clogged with debris like leaves and sticks. Remove everything carefully and return the basket to its place. The basket might be broken or distorted. If so, the impeller of the pump may have some debris on it as well. Clean the impeller, and put in a new basket if the old one is damaged, as it may be harmful for the pump. The strainer top is sealed with a gasket or “O”-ring, which you should also check for cleanliness. If it’s bent out of shape, replace it.
Step 4 – Fill the Strainer
Use your garden hose to run water into the strainer. Then, put the strainer lid back on and push it down well, twisting it into place securely with your hands only. If there are knobs, use both your hands to tighten them firmly and evenly. Try to avoid using a wrench. If you over-tighten, the knobs might break.
Step 5 – Run Water Through the Pump
Switch on the pump, then open one suction side valve very slowly. Within a minute, the pump should be able to catch its prime and get the water flowing through it. If it doesn’t catch within a minute, shut the valve and switch off the pump. Allow the water to flow by reopening the strainer valve.
Release the pressure by opening the air relief valve on the filter. Repeat the entire procedure by refilling the strainer with water, closing the lid, turning on the pump and opening the same valve. These steps may have to be repeated several times before you purge all the air so the water can pass freely through the pump.
Step 6 – Add All the Lines
Slowly open the other valves, one after the other. With every line, the same procedure has to be followed to remove the air from the line without losing the prime.
If your above-ground pool pump keeps losing the prime when you turn it off, try to release the air in the filter first before you turn off the pump. You should always close your suction side valves and then proceed to open the strainer lid. The water is then held right up to the valve, which should make it easy to re-prime.
So you have finished reading the how to prime my intex pool pump topic article, if you find this article useful, please share it. Thank you very much. See more: how to prime a summer waves pool pump, how to prime a pool pump hayward, how to prime pool pump, can’t get pool pump to prime, how long does it take to prime a pool pump, how to prime intex sand filter pump, how to prime a pool pump with sand filter, how to prime pool pump with cartridge filter
