You are looking for information, articles, knowledge about the topic nail salons open on sunday near me how to scrap a starter on Google, you do not find the information you need! Here are the best content compiled and compiled by the Chewathai27.com team, along with other related topics such as: how to scrap a starter how to scrap a generator, starter scrap price, scrap alternators and starters prices, alternator scrap, alternator scrap price, generator scrap value, how much copper in alternator, who buys used starters and alternators near me
Contents
How much can you scrap a starter for?
…
Starters Scrap Price.
| Region | Price |
|---|---|
| North America, USA East Coast | $ 0.24 per Lb |
| USA West Coast | $ 0.23 per Lb |
| USA Midwest | $0.24 per Lb |
Can you scrap a starter motor?
Scrap Car Starters for Top Prices
While local prices can vary, you can almost always be sure to get around 13 cents per pound for car starters and alternators. Here’s what you need to know: Starters are valued because they are wound with copper wire, one of the most valuable scrap metals on the market.
How much copper does a starter have?
Starters, generators, and alternators contain an average of 2.8, 2.6, and 1.5 pounds of copper, respectively. Alternators also contain 3 to 4 pounds of aluminum. Most of the remaining metal is iron. About one-half of the starters have a solenoid that contains 0.5 pounds of copper.
How much is a starter worth?
The cost of rebuild parts for a starter can range from as little as $50 to as much as $350. A brand-new starter can range from $80 to over $350. For a qualified mechanic to replace or rebuild your starter, you can expect to pay between $150 and over $1,100.
What can you do with old starters?
Freeze it: Sourdough starter can be stored in the freezer for up to one year. You can also store discarded sourdough starter in the freezer to use for a future recipe like many of those below. Dehydrate it: Another way to store sourdough starter long term is to dry it out.
How much does a starter weigh?
The stock starter weighs in at a hefty 21.70 pounds, while the Powermaster starter weighs just 8.85 pounds.
What has the most copper in it to scrap?
Older appliances have more copper which gives you more scrap and more money. Washers, dryers, refrigerators, and air conditioners make great scrap appliances for their copper coils.
How much copper is in a electric motor?
On average out of the 10lbs., the copper inside is only about 10-15% of the weight which would equal about 1.5 pounds.
What is the price of copper per pound?
| Copper Spot Price | Spot Change | |
|---|---|---|
| Copper Price per Pound | $3.34 | 0.03 |
| Copper Price per Ounce | $0.21 | 0.00 |
| Copper Price per Ton | $6,680.00 | 60.00 |
Can you scrap engines?
Engine is Ready to Scrap
If the engine cannot be used as anything other than raw materials, it will end up at a specialist recycling centre. There, it will suffer the same fate as the other metal parts of your car – into the shredder it goes!
How do you remove copper motor rotor?
- First step – dividing copper. It’s needed to cut the copper until the central pipe of the rotor. …
- Second step – Burning. To divide the copper from the rotor it’s needed to burn it in a fire. …
- Recycling material.
How much does a starter weigh?
The stock starter weighs in at a hefty 21.70 pounds, while the Powermaster starter weighs just 8.85 pounds.
What has the most copper in it to scrap?
Older appliances have more copper which gives you more scrap and more money. Washers, dryers, refrigerators, and air conditioners make great scrap appliances for their copper coils.
How much copper is in a electric motor?
On average out of the 10lbs., the copper inside is only about 10-15% of the weight which would equal about 1.5 pounds.
Starters Scrap – Where to Sell, Prices, Grades, ISRI Specs
- Article author: www.scrapmonster.com
- Reviews from users: 30051
Ratings - Top rated: 4.1
- Lowest rated: 1
- Summary of article content: Articles about Starters Scrap – Where to Sell, Prices, Grades, ISRI Specs Updating …
- Most searched keywords: Whether you are looking for Starters Scrap – Where to Sell, Prices, Grades, ISRI Specs Updating Starters Scrap are found in cars, trucks and other vehicles. They are filled with copper wire inside. The copper wire content offers scrap metal value to them. Starters Scrap
- Table of Contents:
What Are Starters Scrap
Starters Scrap Price
Where can you sell Starters scrap
Having loads of Starters Scrap
Recycle Starters | Scrap Stop
- Article author: myscrapstop.com
- Reviews from users: 25029 Ratings
- Top rated: 4.7
- Lowest rated: 1
- Summary of article content: Articles about Recycle Starters | Scrap Stop Updating …
- Most searched keywords: Whether you are looking for Recycle Starters | Scrap Stop Updating Recycling starters? Request your price ang get the top money in LA.
- Table of Contents:
Scrapped Starter Motors & Alternators Recycling
- Article author: www.911metallurgist.com
- Reviews from users: 10146 Ratings
- Top rated: 3.5
- Lowest rated: 1
- Summary of article content: Articles about Scrapped Starter Motors & Alternators Recycling Updating …
- Most searched keywords: Whether you are looking for Scrapped Starter Motors & Alternators Recycling Updating
- Table of Contents:
Starters
Generators
Alternators
Dismantling of Starters and Generators
Copper Removal From A Cars Starter Flat Bar Copper – YouTube
- Article author: www.youtube.com
- Reviews from users: 24716 Ratings
- Top rated: 3.7
- Lowest rated: 1
- Summary of article content: Articles about Copper Removal From A Cars Starter Flat Bar Copper – YouTube Updating …
- Most searched keywords: Whether you are looking for Copper Removal From A Cars Starter Flat Bar Copper – YouTube Updating Copper flat bar so handy for so many things. Thank You for watching. SUBSCRIBE if you would its always up to you.Copper Removal From A Cars Starter Flat Bar Copper, Copper Removal From A Cars Starter, Flat Bar Copper, Copper Removal, Removal From A Cars Starter Flat Bar Copper, Copper
- Table of Contents:
Scrapped Starter Motors & Alternators Recycling
- Article author: www.911metallurgist.com
- Reviews from users: 37320 Ratings
- Top rated: 3.5
- Lowest rated: 1
- Summary of article content: Articles about Scrapped Starter Motors & Alternators Recycling Currently, the starters, generators, and alternators scrapped annually are estimated to contain 20,000 tons of copper and 130,000 tons of iron. …
- Most searched keywords: Whether you are looking for Scrapped Starter Motors & Alternators Recycling Currently, the starters, generators, and alternators scrapped annually are estimated to contain 20,000 tons of copper and 130,000 tons of iron.
- Table of Contents:
Starters
Generators
Alternators
Dismantling of Starters and Generators
starter scrapping
- Article author: www.scrapmetalforum.com
- Reviews from users: 24204 Ratings
- Top rated: 3.1
- Lowest rated: 1
- Summary of article content: Articles about starter scrapping starter scrapping. I been buying starters for $2.00 a piece. Only problem is they are like treadmill motors. Permanent dc magnet with the copper … …
- Most searched keywords: Whether you are looking for starter scrapping starter scrapping. I been buying starters for $2.00 a piece. Only problem is they are like treadmill motors. Permanent dc magnet with the copper … I been buying starters for $2.00 a piece. Only problem is they are like treadmill motors. Permanent dc magnet with the copper wrapped around the rotor. And its sealed in epoxy. And the solenoids are sealed. No good way to get them open.
What do you guys do with them? I see like a $1.00 profit for 10 mins work, because all there is steel, alu cast nose…and the solenoid/rotor, going into the motor bucker at 20c a lb.
What are your thoughts?
Been thinking about starting a fire to burn
- Table of Contents:
starter scrapping
The Following User Says Thank You to freonjoe for This Post
Recycle Starters | Scrap Stop
- Article author: myscrapstop.com
- Reviews from users: 39045 Ratings
- Top rated: 3.7
- Lowest rated: 1
- Summary of article content: Articles about Recycle Starters | Scrap Stop Recycling starters? … Scrap Car Starters for Top Prices … access to old cars, alternators and starters are easy to come by and perfect for scrapping. …
- Most searched keywords: Whether you are looking for Recycle Starters | Scrap Stop Recycling starters? … Scrap Car Starters for Top Prices … access to old cars, alternators and starters are easy to come by and perfect for scrapping. Recycling starters? Request your price ang get the top money in LA.
- Table of Contents:
METAL RECOVERY BY DISMANTLING OF SCRAPPED STARTER MOTORS, AUTO GENERATORS, AND ALTERNATORS
- Article author: trid.trb.org
- Reviews from users: 37081 Ratings
- Top rated: 3.1
- Lowest rated: 1
- Summary of article content: Articles about METAL RECOVERY BY DISMANTLING OF SCRAPPED STARTER MOTORS, AUTO GENERATORS, AND ALTERNATORS METAL RECOVERY BY DISMANTLING OF SCRAPPED STARTER MOTORS, AUTO GENERATORS, … The scrap copper yield would be 280, 390, and 45 pounds, respectively, … …
- Most searched keywords: Whether you are looking for METAL RECOVERY BY DISMANTLING OF SCRAPPED STARTER MOTORS, AUTO GENERATORS, AND ALTERNATORS METAL RECOVERY BY DISMANTLING OF SCRAPPED STARTER MOTORS, AUTO GENERATORS, … The scrap copper yield would be 280, 390, and 45 pounds, respectively, … Abandoned cars, Abandonment, Ac generators, Alternating current, Alternators, Aluminum, Automobiles, Copper, Dismantling, Electric generators, Engine starters, Generators, Iron, Materials recovery, Materials recovery (Mining), Metal scrap, Motor starters, Motors, Recovery, Scrap metal, Solid waste disposal
- Table of Contents:
Site Contents
Connect with TRB
Media Info
SubjectIndex Terms
Filing Info
SCRAPPING Starters & Generators for COPPER | The H.A.M.B.
- Article author: www.jalopyjournal.com
- Reviews from users: 9943 Ratings
- Top rated: 4.8
- Lowest rated: 1
- Summary of article content: Articles about SCRAPPING Starters & Generators for COPPER | The H.A.M.B. Is there an easy way to pull the copper out of a starter and generator for scrap, or is the time envolved not worth it? …
- Most searched keywords: Whether you are looking for SCRAPPING Starters & Generators for COPPER | The H.A.M.B. Is there an easy way to pull the copper out of a starter and generator for scrap, or is the time envolved not worth it? Is there an easy way to pull the copper out of a starter and generator for scrap, or is the time envolved not worth it? Just wondering if I’d make more…
- Table of Contents:
Recycling Starters | Alternators | Scrap prices
- Article author: forscrap.com
- Reviews from users: 21276 Ratings
- Top rated: 4.1
- Lowest rated: 1
- Summary of article content: Articles about Recycling Starters | Alternators | Scrap prices Many metal scrap yards accept all kinds of spare car parts. The pricing for alternators and starters can be high, as they are a great source of scrap copper … …
- Most searched keywords: Whether you are looking for Recycling Starters | Alternators | Scrap prices Many metal scrap yards accept all kinds of spare car parts. The pricing for alternators and starters can be high, as they are a great source of scrap copper … Here we buy scrap alternators/starters with the top price in Los Angeles. Call (866)567-27-27 for quote.
- Table of Contents:
See more articles in the same category here: Top 122 tips update new.
Where to Sell, Prices, Grades, ISRI Specs
Starters Scrap are found in cars, trucks and other vehicles. They are filled with copper wire inside. The copper wire content offers scrap metal value to them.
What Are Starters Scrap?
Starters are found in cars, trucks and other vehicles. They are filled with copper wire inside. The copper wire content offers scrap metal value to them. They must be free of large attachments. The starters in automotives have limited life and require frequent replacement.
Starters Scrap Price
The copper content inside the Starters decides its price. The prices can vary from yard to yard. The sellers of Starter scrap may cross check with a number of nearby yards to obtain best price for their scrap.
Given below is a table which provides the export price of Starters across different parts of the world as of mid-August, 2020.
Region Price North America, USA East Coast $ 0.24 per Lb USA West Coast $ 0.23 per Lb USA Midwest $0.24 per Lb
Source : ScrapMonster
Scrap Monster Scrap Copper Prices offers Live Copper Scrap Export Prices.
The Scrap Yard Prices section which provides the details of market price offered by various scrap yards for Starters Scrap.
Where can you sell Starters scrap?
Please note that Starters scrap is not accepted by all scrap metal yards. In general, all auto recyclers may be willing to buy this category of scrap. Hence make sure that your local scrap yard accepts Starters scrap and that reasonable to fair prices are offered for the sold materials.
It is advisable to open the unit and separate the materials. However, if you have only limited quantity of Starters scrap, it is advisable to sell them in the same condition as they exist, because the operation to break them apart is quite labor-intensive.
A list of few scrap yards in the US that accept Starters is provided below:
-Brothers Auto Salvage, Cadet, Missouri. -Metalico Elizabeth, Elizabeth, New Jersey. -DUSA Metals Recycling, Knoxville, Tennessee. -Cooter Enterprises, Inc., Omaha, Nebraska.
You may use our ‘Scrap Yard Finder’ to search and find more scrap yards in your region.
On our US Scrap Yard Directory, we provide a list of scrap yards in the US.
Similarly, the list of scrap yards in Canada is easily available in Scrap Yards in Canada.
Having loads of Starters Scrap?
The Starters in cars, trucks and other automobiles needs to be replaced with new ones periodically, thereby resulting in huge quantities of scrap starters. If you have large amount of Starters, it is advisable to spend time removing wires out of it, so as to obtain the best pricing.
The Scrap Monster Scrap Marketplace is an advanced trading platform where materials are traded daily by many of our members.
Post and/or search the latest “Sell Offers” for Copper scrap.
Post and/or Search the latest “Buy Offers” for Copper scrap.
Only registered members have access to posting new buy and sell listings. You can LOG IN or REGISTER
Scrapped Starter Motors & Alternators Recycling
There are two principal methods in use for processing the 8 million cars that are scrapped annually in the United States. About one-half of the cars are processed by shredding in which automobiles minus radiators, batteries, engines, gas tanks, and seats are ripped into fist-sized chunks and then magnetically separated to produce a ferrous scrap fraction and a nonmagnetic fraction. The remaining half of the cars are processed by hand removal of nonferrous, steel, and cast iron parts from the burned or unburned cars, followed by baling or shearing of the stripped hulks. For both methods, the starter and generator (or alternator) are generally removed, although the number of generators still exceeds alternators on scrapped cars, this ratio will shift markedly in a few years because, by 1968, alternators became standard equipment on almost all cars. Currently, the starters, generators, and alternators scrapped annually are estimated to contain 20,000 tons of copper and 130,000 tons of iron. Improved techniques for incineration and dismantling have been reported and are gradually being adopted by scrap processors.
Historically, most of the generators and starters stripped from junked automobiles have either been sold for used parts (with or without rebuilding), treated by chemical dissolution of the copper, or directly smelted for recovery of the copper.
Among the smaller processors, non rebuildable starters and generators have been commonly discarded or given to employees for free time dismantling and sale of the products. Attempts to process starters and generators in shredders followed by magnetic separation of the iron from the nonferrous metals have had indifferent success owing to entanglement of the fragmented components.
Commercial operations to recover copper as metal and chemicals from generators and starters by leaching have been conducted on a limited basis. Ammonium carbonate solution was used for selectively dissolving the copper. A technique for possibly improving the recovery of the copper from the leach solution by adding sulfur to precipitate copper sulfide was tested in the laboratory by the Bureau of Mines but was not further developed.
A process for selectively melting the copper in a fused-salt bath also was developed by the Bureau, but it has not been adopted commercially. Copper is readily recovered by melting when starters and generators are charged to the converting furnace in a copper smelter, but the accompanying iron is lost in the smelter slag.
This report describes a laboratory study of techniques for dismantling starters, generators, and alternators using hand and power tools in conjunction with small hydraulic presses, power handsaws, and lathes.
Test Materials
The starters, generators, and alternators used in this investigation were obtained from a Utah metal salvage firm. A wide range of types of starters and generators was readily available, while only four types of alternators were used. Both incinerated and unburned units were tested. Starters and generators weigh about 20 to 25 pounds, and alternators weigh about 12 to 15 pounds. Starters, generators, and alternators contain an average of 2.8, 2.6, and 1.5 pounds of copper, respectively. Alternators also contain 3 to 4 pounds of aluminum. Most of the remaining metal is iron. About one-half of the starters have a solenoid that contains 0.5 pounds of copper. Figure 1 is a schematic diagram of a typical starter motor with a solenoid, a generator; and an alternator.
Experimental Work
Time and motion studies were made of the disassembly of test units using hand and power tools, hydraulic presses, power-saws, and lathes to prepare copper, aluminum, and steel products of marketable quality. These studies were made in batch lots of from 15 to 50 generators and starters, and with batch lots of 5 alternators. The dismantling times were averaged to project a working day. The dismantling tools and equipment were arranged in a production line sequence for each group. A few unburned units were incinerated in a laboratory furnace at 600° C. About 30 to 60 minutes of burning time was required to remove grease , oil, or lacquer. A few units were chilled to minus 196° C by immersion in liquid nitrogen to test the effect of chilling on embrittlement prior to crushing. No appreciable embrittlement of the steel encasement was obtained. There were 150 starters, 200 generators, and 15 alternators dismantled during the study. The most effective dismantling techniques are herein described.
Starters
The procedure developed for dismantling a starter was (1) removing the endplate with a speedwrench, (2) press-breaking the cast-iron bendix (pinion-gear) housing to release the armature brushes and bushings, (3) separating the armature from the bendix by cutting the shaft with a bandsaw (about one- fourth of the starters do not require this operation), (4) press-crushing the commutator to loosen the contacts, (5) pressing out the field coils from inside the starter case, (6) cutting the armature wire and field coil wire simultaneously on a lathe using suitable saw fixtures, and (7) collecting the armature and field coil wire.
More than half of the starters have an attached starter solenoid containing a spool of fine copper wire. The procedure used to recover the copper wire was (1) cutting the capsulelike solenoid case lengthwise with a torch and removing the “lid,” (2) melting the inner aluminum spool core using a torch, and (3) recovering the copper spool.
The average time required for one man to dismantle and recover the copper from a typical incinerated starter was 3 minutes; and from a starter solenoid, 1 minute. Dismantling an unincinerated starter required 4 minutes. About 2.8 pounds of copper was recovered from the starter motor and 0.5 pound of copper from the starter solenoid.
Generators
The procedure developed for dismantling a generator was (1) removing the endplate with a speed wrench, (2) separating the armature, brushes, and bushing from the case, (3) pressing out the field coil from inside the case and press-crushing the commutator to loosen the contacts, (4) cutting the armature wire and field coil wire simultaneously on a lathe using suitable saw fixtures, (5) removing the armature wire from the rotor by shaking, and (6) collecting the armature and field coil wires. About 0.1 pound of copper contained in wire, brass fittings, and brushes was collected separately from the main portion of copper wire. The average time required to dismantle and recover the copper wire from an incinerated generator was 2 minutes; and from an unincinerated generator, 3 minutes. About 2.6 pounds of copper was recovered from each generator. Figure 2 shows pressing the commutator to loosen the contacts, while figure 3 shows the completely dismantled generator.
Alternators
Fewer alternators than starters and generators were disassembled. The alternators not only were more difficult to dismantle, but yielded substantially lower metal values. Appreciable improvement may be possible with the following procedure: (1) Removing three or four nuts to free the field coil and allow separation of the aluminum case from the armature, (2) press-removing the shaft and pulley from the armature, (3) cutting the copper-containing field coil away from the starter with a hacksaw, and (4) recovering the copper wire from the armature as described for generators. Dismantling an incinerated alternator required 9 minutes and dismantling an unincinerated
alternator required 10 minutes. Approximately 1.5 pounds of copper was recovered from each alternator.
Dismantling of Starters and Generators
The time and motion studies indicate that an individual equipped with power handtools and conveniently placed hydraulic press, power bandsaw, and power lathe could, in an 8-hour day, dismantle about 100 starters, or 150 generators, or 30 alternators. The scrap copper yield would be 280, 390, and 45 pounds, respectively. The alternators also would yield about 100 pounds of aluminum. The iron yield would be about seven times that of the copper. At scrap metal prices of $0.15 per pound for aluminum, $0.50 per pound for copper, and $30 per ton for iron, the marketable value of the starter, generator, and alternator products that one man could dismantle in a day would be $170, $235, and $42. These values may be attractive for starters and generators, but show that improvements are needed to speed the dismantling procedure for alternators. The same starters, generators, and alternators, if sold without disassembly at $0,035 per pound, would have values of $84.00, $110.25, and $10.50, respectively.
By using a team disassembly line approach, a six-man crew equipped with power handtools, three presses, one lathe, and a bandsaw presumably could dismantle more than six times as many starters as an individual. For dismantling generators, the six-man crew would be equipped with power handtools, one press, and two lathes.
Summary
Time and motion studies showed that scrapped starters and generators can be efficiently disassembled into separately marketable copper and iron components by use of inexpensive hand and power tools, hydraulic presses, handsaws, and power lathes. Substantially improved techniques appear needed for the dismantling of alternators. Local availability of enough scrapped starter motors and generators at a suitable cost may justify a disassembly team approach in processing these items.
Scrapped Starter Motors & Alternators Recycling
There are two principal methods in use for processing the 8 million cars that are scrapped annually in the United States. About one-half of the cars are processed by shredding in which automobiles minus radiators, batteries, engines, gas tanks, and seats are ripped into fist-sized chunks and then magnetically separated to produce a ferrous scrap fraction and a nonmagnetic fraction. The remaining half of the cars are processed by hand removal of nonferrous, steel, and cast iron parts from the burned or unburned cars, followed by baling or shearing of the stripped hulks. For both methods, the starter and generator (or alternator) are generally removed, although the number of generators still exceeds alternators on scrapped cars, this ratio will shift markedly in a few years because, by 1968, alternators became standard equipment on almost all cars. Currently, the starters, generators, and alternators scrapped annually are estimated to contain 20,000 tons of copper and 130,000 tons of iron. Improved techniques for incineration and dismantling have been reported and are gradually being adopted by scrap processors.
Historically, most of the generators and starters stripped from junked automobiles have either been sold for used parts (with or without rebuilding), treated by chemical dissolution of the copper, or directly smelted for recovery of the copper.
Among the smaller processors, non rebuildable starters and generators have been commonly discarded or given to employees for free time dismantling and sale of the products. Attempts to process starters and generators in shredders followed by magnetic separation of the iron from the nonferrous metals have had indifferent success owing to entanglement of the fragmented components.
Commercial operations to recover copper as metal and chemicals from generators and starters by leaching have been conducted on a limited basis. Ammonium carbonate solution was used for selectively dissolving the copper. A technique for possibly improving the recovery of the copper from the leach solution by adding sulfur to precipitate copper sulfide was tested in the laboratory by the Bureau of Mines but was not further developed.
A process for selectively melting the copper in a fused-salt bath also was developed by the Bureau, but it has not been adopted commercially. Copper is readily recovered by melting when starters and generators are charged to the converting furnace in a copper smelter, but the accompanying iron is lost in the smelter slag.
This report describes a laboratory study of techniques for dismantling starters, generators, and alternators using hand and power tools in conjunction with small hydraulic presses, power handsaws, and lathes.
Test Materials
The starters, generators, and alternators used in this investigation were obtained from a Utah metal salvage firm. A wide range of types of starters and generators was readily available, while only four types of alternators were used. Both incinerated and unburned units were tested. Starters and generators weigh about 20 to 25 pounds, and alternators weigh about 12 to 15 pounds. Starters, generators, and alternators contain an average of 2.8, 2.6, and 1.5 pounds of copper, respectively. Alternators also contain 3 to 4 pounds of aluminum. Most of the remaining metal is iron. About one-half of the starters have a solenoid that contains 0.5 pounds of copper. Figure 1 is a schematic diagram of a typical starter motor with a solenoid, a generator; and an alternator.
Experimental Work
Time and motion studies were made of the disassembly of test units using hand and power tools, hydraulic presses, power-saws, and lathes to prepare copper, aluminum, and steel products of marketable quality. These studies were made in batch lots of from 15 to 50 generators and starters, and with batch lots of 5 alternators. The dismantling times were averaged to project a working day. The dismantling tools and equipment were arranged in a production line sequence for each group. A few unburned units were incinerated in a laboratory furnace at 600° C. About 30 to 60 minutes of burning time was required to remove grease , oil, or lacquer. A few units were chilled to minus 196° C by immersion in liquid nitrogen to test the effect of chilling on embrittlement prior to crushing. No appreciable embrittlement of the steel encasement was obtained. There were 150 starters, 200 generators, and 15 alternators dismantled during the study. The most effective dismantling techniques are herein described.
Starters
The procedure developed for dismantling a starter was (1) removing the endplate with a speedwrench, (2) press-breaking the cast-iron bendix (pinion-gear) housing to release the armature brushes and bushings, (3) separating the armature from the bendix by cutting the shaft with a bandsaw (about one- fourth of the starters do not require this operation), (4) press-crushing the commutator to loosen the contacts, (5) pressing out the field coils from inside the starter case, (6) cutting the armature wire and field coil wire simultaneously on a lathe using suitable saw fixtures, and (7) collecting the armature and field coil wire.
More than half of the starters have an attached starter solenoid containing a spool of fine copper wire. The procedure used to recover the copper wire was (1) cutting the capsulelike solenoid case lengthwise with a torch and removing the “lid,” (2) melting the inner aluminum spool core using a torch, and (3) recovering the copper spool.
The average time required for one man to dismantle and recover the copper from a typical incinerated starter was 3 minutes; and from a starter solenoid, 1 minute. Dismantling an unincinerated starter required 4 minutes. About 2.8 pounds of copper was recovered from the starter motor and 0.5 pound of copper from the starter solenoid.
Generators
The procedure developed for dismantling a generator was (1) removing the endplate with a speed wrench, (2) separating the armature, brushes, and bushing from the case, (3) pressing out the field coil from inside the case and press-crushing the commutator to loosen the contacts, (4) cutting the armature wire and field coil wire simultaneously on a lathe using suitable saw fixtures, (5) removing the armature wire from the rotor by shaking, and (6) collecting the armature and field coil wires. About 0.1 pound of copper contained in wire, brass fittings, and brushes was collected separately from the main portion of copper wire. The average time required to dismantle and recover the copper wire from an incinerated generator was 2 minutes; and from an unincinerated generator, 3 minutes. About 2.6 pounds of copper was recovered from each generator. Figure 2 shows pressing the commutator to loosen the contacts, while figure 3 shows the completely dismantled generator.
Alternators
Fewer alternators than starters and generators were disassembled. The alternators not only were more difficult to dismantle, but yielded substantially lower metal values. Appreciable improvement may be possible with the following procedure: (1) Removing three or four nuts to free the field coil and allow separation of the aluminum case from the armature, (2) press-removing the shaft and pulley from the armature, (3) cutting the copper-containing field coil away from the starter with a hacksaw, and (4) recovering the copper wire from the armature as described for generators. Dismantling an incinerated alternator required 9 minutes and dismantling an unincinerated
alternator required 10 minutes. Approximately 1.5 pounds of copper was recovered from each alternator.
Dismantling of Starters and Generators
The time and motion studies indicate that an individual equipped with power handtools and conveniently placed hydraulic press, power bandsaw, and power lathe could, in an 8-hour day, dismantle about 100 starters, or 150 generators, or 30 alternators. The scrap copper yield would be 280, 390, and 45 pounds, respectively. The alternators also would yield about 100 pounds of aluminum. The iron yield would be about seven times that of the copper. At scrap metal prices of $0.15 per pound for aluminum, $0.50 per pound for copper, and $30 per ton for iron, the marketable value of the starter, generator, and alternator products that one man could dismantle in a day would be $170, $235, and $42. These values may be attractive for starters and generators, but show that improvements are needed to speed the dismantling procedure for alternators. The same starters, generators, and alternators, if sold without disassembly at $0,035 per pound, would have values of $84.00, $110.25, and $10.50, respectively.
By using a team disassembly line approach, a six-man crew equipped with power handtools, three presses, one lathe, and a bandsaw presumably could dismantle more than six times as many starters as an individual. For dismantling generators, the six-man crew would be equipped with power handtools, one press, and two lathes.
Summary
Time and motion studies showed that scrapped starters and generators can be efficiently disassembled into separately marketable copper and iron components by use of inexpensive hand and power tools, hydraulic presses, handsaws, and power lathes. Substantially improved techniques appear needed for the dismantling of alternators. Local availability of enough scrapped starter motors and generators at a suitable cost may justify a disassembly team approach in processing these items.
So you have finished reading the how to scrap a starter topic article, if you find this article useful, please share it. Thank you very much. See more: how to scrap a generator, starter scrap price, scrap alternators and starters prices, alternator scrap, alternator scrap price, generator scrap value, how much copper in alternator, who buys used starters and alternators near me
