Hard Drive Stiction Fix? Top Answer Update

Twitter Facebook Google Plus Linked

What should I do with a noisy drive?

Seagate does not have a utility that can reduce most hard drive ambient noise. This article explains.

Seagate does not have a utility that can reduce most hard drive ambient noise. While modern drives are extremely quiet, every drive makes some level of noise during operation. Typically, the faster the drive motor spins, the higher the resulting tone and the greater the likelihood of a deep hum. Most drives don’t make any noise that most people can hear, but there are a few exceptions.

It is also normal for the drive to make a sort of “chatter” or “click” sound as it reads and writes data. Also, some drives occasionally perform offline scans, resulting in similar noises even when the drive isn’t actively reading or writing.

If you are concerned about the noise your drive is making, please test it with SeaTools. If it fails the test, the noise may be due to a mechanical issue or something similar. Seagate recommends replacing the hard drive in this case.

If an external drive beeps, it may be due to insufficient power. Even if your drive has never beeped, sometimes as drives age they require a little more power, which can cause them to beep when plugged in. Most beeps occur with USB powered drives that do not have a separate power supply.

If the drive isn’t recognized either, please use one of our external drive troubleshooters to try to recognize it.

Disconnect the drive from any USB hub to which it is connected. Plug it directly into the USB port.

Try connecting the drive to different USB ports on your computer. It may not beep when plugged into a different USB port.

If you are using a desktop computer, connect the drive to a USB port on the back of the computer.

Replace the USB cable with a new or known-good cable.

Some USB-only drives connect with a “Y-cable” such as B. the one shown in Document ID: 205479. Connect the drive with both ends of the Y-cable for maximum performance.

If attempting to use an eSATA connection with a GoFlex drive, make sure it is a powered eSATA port. For more information, see Document ID: 214371.

If the beeping continues, connect the drive to another computer to see if the beeping follows the drive. If the drive works fine on another computer, the original device is not providing enough power to run your drive. A powered USB hub can help.

If the noise from around your drive has changed recently, or is an excessive grinding or rattling noise, this may indicate an internal or external physical problem with the drive.

Information specific to internal drives:

Noise from the fans in the computer’s power supply is often mistakenly referred to as hard drive noise. To isolate whether the noise is coming from the hard drive or one of the fans, you can issue a spin down command through SeaTools. Use the Acoustic Spin Down Test to temporarily spin down internal drives so you can hear changes in noise levels. For instructions, see Document ID: 201271. If the noise goes away, the drive was making the noise. If the noise persists, then the drive is not the cause of the noise.

If your internal hard drive passes the SeaTools diagnostic test, please check for a firmware update for your drive. See the SeaTools documentation for instructions.

If the drive noise is unbearable or accompanied by persistent undetected issues that our troubleshooting experts cannot resolve, you may need to replace the drive.

To check the warranty status for your drive, please visit our warranty validation page.

A beeping hard drive should only be opened in a clean room facility to obtain the data it contains.

Hard drives make various noises that indicate something is not working properly, but a beep is a surefire indicator that your hard drive is failing. What sounds like a beep is actually the sound of your drive’s internal components trying to turn on and failing.

The basics behind the sound

The most common cause of a beep is caused by a hard drive’s internal components not being able to move normally. It’s not a programmed “beep” you hear, it’s the sound of stuck parts inside the device trying to move. Some of the causes of a beeping hard drive are:

Fixed operating arm

Stiction of the stacked heads under the parking ramp or on the turntable Stiction is the friction that prevents stationary surfaces from moving

Defective or seized motor or spindle This is preventing the platters from turning

Shorted Printed Circuit Board (PCB)

Dangers of a beeping drive

Generally, the platter of a hard drive spins at thousands of revolutions per minute, and issues like sticking read/write heads affect the ability of the moving parts to locate your data. Attempting to power your device with parts stuck will only result in further physical damage to your drive. In the case of stuck read/write heads, turning on the drive will scratch the platters, resulting in severe data loss.

The severity of the physical damage requires the help of a data recovery expert. If you continue to spin up your drive without fixing the problem, you not only degrade the health of your drive, you also ruin your chances of a successful recovery. As long as the drive remains powered off and untouched, chances are your files can be retrieved.

Prevent and recover from a beeping hard drive

Data loss disasters like a beeping drive are most commonly caused by physical damage such as: B. by falling. If you drop your storage device or it sustains damage that causes it to beep, do not attempt to recover it yourself. How-to videos might seem helpful, but opening your drive outside of a clean room environment will only expose your media to the elements, causing further damage and limiting your chances of successfully recovering your data.

Due to the mechanical nature of a hard disk drive, there is a higher risk of physical failure. So, be extra careful when handling your external drives or device with an internal hard drive. One of the best solutions is to create a backup of your important files so that you don’t get into a difficult situation when your drive encounters data loss scenario.

Proven data recovery for beeping drives

Secure Data Recovery recovered files from all types of data loss scenarios including beeps. We work with all types of manufacturers and operating systems and have an overall success rate of over 96%. If your hard drive is beeping, turn it off immediately and contact a professional to recover your critical data. Our customer representatives are available 24 hours a day to handle your case at 1-800-388-1266.

Share this article:

Hard drives are usually almost silent, but some make a muffled clicking sound when being accessed or powered off – this is normal.

On the other hand, if you only hear occasional noises or noises you’ve never heard before — like clicking, grinding, vibration, or squeaking — your hard drive may be defective. Datacent offers some sample hard drive failure sounds that may sound like what you are hearing right now.

The following steps will help you determine if the hard drive really is to blame, and if so, what to do next before all your valuable data is lost forever.

Derek Abella / Lifewire

What to do if your hard drive is making noise

Make sure the hard drive is the source of the noise and not another hardware component. For example, if you unplug the power and data cables from the hard drive but still hear the sound as the computer boots up, it’s clear that the problem isn’t with the hard drive. Try each scenario to really locate the source. If the hissing goes away when you plug in the power cord but comes back when you connect the data cable to the hard drive, you probably need to replace the data cable. Check out our guide to opening a desktop computer case if you’re not sure how to get inside your computer. If you are sure that the hard drive itself is to blame, run free hard drive diagnostic software that is already available on many computers or on the internet. The more advanced diagnostic software is also available for a fee from various developers. HDDScan. If you are running diagnostic software, it is best to close all other programs and unplug any other drives or devices you are not testing to avoid skewing the results. At best, the diagnostic software only marks the bad areas of the hard drive as “bad” and prevents the computer from using them in the future. It won’t actually fix a hard drive that physically fails. If the fixes made by the diagnostic software don’t temporarily fix the hard drive noise, back up your system and replace the hard drive. If the diagnostic software helps fix the clicking, grinding, or squeaking noise, this solution provides a temporary fix. There is a chance that the hard drive will continue to fail until it is completely unusable. The permanent solution is to backup your system and replace the hard drive. However, in rare cases where a hard drive is only noisy when accessing specific data on your drive, those specific sectors could be bad — a problem that some diagnostic software can fix.

More help troubleshooting hard drive noise

Since there is no good way to fix a failed hard drive, protecting your data with regular backups is essential. With a current backup, recovering from a hard drive failure is as easy as installing a new hard drive and restoring your data.

The best way to back up your data is with an online backup service as your files are stored in the cloud and are less prone to loss or destruction. However, a faster method is to use a free backup program – some of these programs can even clone the files from the failed hard drive and place them on a new, working hard drive.

Solid State Drives (SSDs) don’t have any moving parts like a magnetic hard drive, so you won’t hear a hard drive fail like you will with a spinning hard drive.

External hard drives make noise too. These noises occur when the drive is connected to the computer due to a power or cable connection issue. Try to troubleshoot external hard drive noise by plugging the power adapter directly into the wall instead of a power strip, using a shorter USB cable, using USB 2.0+ ports, or plugging the hard drive into a USB port on the back of the Connect computers instead of in front.

A fragmented hard drive creates additional drive activity. Use a free disk defragmenter to extend the life of your hard drive, but it probably won’t fix the problem on most noisy hard drives.

Check out our file recovery FAQs if you need to recover your files from a failed hard drive.

Although not common, it is possible that a hard drive noise is due to a faulty device driver. See How to update drivers in Windows to learn how to update a hard drive driver.

Other noises a computer can make

The hard drive is not the only component in a computer. They also have a power supply, fan, disk drive, and other things that might make noise. It’s important to identify where the noise is coming from so you can understand what to look for.

For example, if your computer is operating in overdrive for a specific task like a memory-hungry video game, it’s normal for the fan to run faster to keep the hardware cool. Instead, there could be something stuck in the fan’s blades that’s making an odd noise — like pet hair.

Read How to fix a computer fan that’s noisy or making noise if you think the true source of the strange noise is actually one of your computer’s fans.

When you open a certain program or window on your computer, you may hear a noise that gets progressively louder—one that can easily be confused with a hard drive noise. This most likely means that a disc in the drive is spinning faster than it did before, allowing the computer to read data from it, which is normal.

Crackling or static noises from the speakers can also be confused with hard drive noise (the cable may not be securely connected to the computer connector), as can some BIOS beep codes and high-pitched howls.

Here’s an infographic guess based on data from Backblaze’s study:

The data shows that hard drives have three failure rate segments. The first segment refers to the first year and a half, where 5% of hard drives fail per year. The high initial failure rate is due to manufacturing defects. Each batch of hard drives contains a few lemons.

After that, the failure rate levels off at 1% per year. This is explained by random drive errors. Then after three years hard drives start to wear out. The bottom line is that a hard drive’s components can only move so much before they begin to fail.

It should be noted that Backblaze uses consumer hard drives, which typically carry a twelve to thirty-six month warranty. So the warranty length seems correct, while enterprise-class hard drives are generally guaranteed for five years or more.

Hard Disk Drives (HDDs) vs Solid State Drives (SSDs)

The two most popular types of hard drives have different life expectancies. My colleague recently wrote an informative blog post that details the difference between HDDs and SSDs and can provide you with extensive information. But here I will address how long each type will last.

Hard drives physically write code to the hard disk in the drive. Because HDDs have tiny moving parts inside, they are more prone to physical failure than SSDs. HDDs can be found in most desktop computers and laptops.

Solid state drives use flash technology to store data. Solid state drives are more expensive but also more reliable than hard disk drives. There is no moving platter in an SSD, so they are not prone to more traditional hard drive failures. However, an SSD still uses a capacitor and power supplies, which can cause it to malfunction.

Ways to prevent your hard drive from failing

You can protect yourself from hard drive failure by taking some precautions. The first step is to have a backup. A completed, up-to-date backup protects you against possible data loss. For advice on how to properly maintain your backup, see the complete guide to backups for home and business users.

The next step is to protect your hard drive environment from threats. Many things can disrupt a hard drive. These include dust, heat, weather, theft, electrical surges and travel hazards.

Finally replace your hard drive after 3-5 years. As you just read, hard drives fail over time. By moving your data to a new hard drive, you create data redundancy and gain more time to safely store your data.

Signs of a failing hard drive

There are numerous subtle signs that your hard drive might be failing. Notice if your computer slows down, freezes frequently, or displays a corrupt data or bad sector warning. Malware viruses and improper shutdown can also affect your hard drive.

For diagnostic help, you can try running your computer in safe mode. Or, for an all-in-one Mac hard drive protection software, try Drive Genius 6, the Apple Genius Bar’s favorite tool. The software automates your hard drive security by checking for logical and physical problems. It can repair directory problems and consistency errors. The latest feature is Malware Protection, which scans your new downloads and old files for known malware.

However, if you notice strange clicking or grinding noises coming from your hard drive, there may be a physical fault. Make sure your hard drive is powered off to avoid further damage. For more information on physical disk failure, visit our current disk recovery page.

How to Navigate Data Recovery on macOS Catalina

Upgrading to macOS Catalina can sometimes cause data recovery issues. If this has happened to you or you just can’t find a specific file on your Mac, there are several ways to fix this problem. First of all, you should make sure that the file was not accidentally moved to the recycle bin. To do this, click on your recycle bin and a window will open where you can search for your file. Just type the name of the file in the search window and search for it.

If your file doesn’t appear in the search window, you may need to search for it some more. Luckily, all Macs come with a built-in backup system called Time Machine. To use Time Machine, open the program that created the file. For example, if it was a document, open Documents. Then use Launchpad to open the Time Machine app. Once inside the app, you should be able to browse for your file and then click Restore to get the file back to your computer.

If none of these options work, consult a professional data recovery specialist to find out how to retrieve your macOS Catalina files without the stress or unnecessary expense.

When your hard drive has failed

There are two main reasons drives fail: logical and physical. In case of logical errors, you can use data recovery software like Data Rescue to get your data back. The data recovery software works for drives that are damaged, erased and crashed.

In the event of a physical hard drive failure, you can contact the Data Rescue Center in Silicon Valley, California. Data Rescue Center offers free shipping, free estimates, and a free no-data-no-charge policy. The Data Rescue Center is the most professional and technologically advanced facility in the United States. Our US-based support staff will help you with all your difficulties to ensure you have a successful recovery.

Replacement Drive Recommendations (Affiliate Links)

There are a variety of options when it comes to drive replacements. Any working drive would allow a system to be operational again. However, we have selected a few replacement drives that we believe are reliable and popular in the industry.

ifixit.com has hundreds of guides on how to extract a drive from most laptops and desktop computers. These guides also provide information about the type of drive in the system to purchase the correct replacement. We recommend an SSD (Solid State Drive) as it offers the best performance and is suitable for most devices. Please visit ifixit.com/Guide for information specific to your system.

SSD (Solid State Drive)

M.2

HDD (hard disk)

Twitter Facebook Google Plus Linked

Identify hard drive noise and determine its meaning

This article provides information on the types of noise you may hear from your Seagate or LaCie external hard drive and what the noise indicates about drive activity and health. An external hard drive will emit a range of noises during normal use that are perfectly normal and to be expected. There are also environmental elements that can affect noise perception: HDD noise can be exaggerated in an otherwise quiet room.

The hard drive can be placed on a surface that amplifies its noise.

Other factors close to the hard drive can reflect its noise.

Note: Hard disk drives (HDD) generate noise due to their rotating parts. Solid state drives (SSD) have no moving parts and are generally quieter.

This document contains a lot of information about the type of noise you may be hearing from your storage device. Check out a list of topics with direct links:

Expected noises

Typically, the faster the drive motor spins, the higher the resulting tone and the greater the likelihood of a deep hum. Hard drives are generally audible, especially 3.5-inch maybe: historically, drives made an acceptable level of audible noise. However, there can be exceptions even in normal use.

A drive can “rattle” or “click” as it reads and writes data. These are soothing sounds that indicate the drive is active. Also, some drives occasionally perform offline scans, resulting in similar noises even when the drive isn’t actively reading or writing.

The various noises that can come from a hard drive during normal use include:

As a hard drive reads or writes data, the platters on the hard drive spin rapidly – this usually emits a whirring noise and can be more pronounced when a hard drive is spinning up or spinning down. Even when not actively accessed by a user, hard drives are often used by the computer in the background, for example during automatic indexing.

Also, the heads of the HDD that read and write the data are constantly making fast movements – this usually sounds like an occasional soft click during use, but can sound like a hard click when the heads are parked, for example during shutdown or when Entering Hibernate mode.

Some external drive enclosures have internal fans, particularly devices with multiple hard drives. These can also produce noises that can be more noticeable in warmer environments where the fan kicks in earlier and more frequently – this sounds like the HDD whirring mentioned above.

When hard drives spin, they create vibrations, and vibration of a hard drive placed on a desk can cause other objects on the desk, or even the desk itself, to make noise.

If an external HDD has its own power supply, you may hear a slight hum coming from the power supply, especially if the power supply is a bit older.

Enterprise-class hard drives are designed to offer higher performance and reliability. However, this increased performance may come with increased noise levels compared to standard drives.

Different applications can cause different noise levels. For example, writing new data to an encrypted volume can generate more noise compared to a standard volume.

With multiple HDDs in one enclosure, the potential for higher noise levels is more likely. This is common for large RAID devices.

This will prevent healthy hard drives from making more noise than necessary

Do not place the external hard drive near the wall. These devices are often designed to “push” sounds out their backs, away from users. However, if placed too close to a wall, these sounds can bounce back.

Do not bring the external hard drive into direct contact with the desk. Especially with certain materials, such as a wooden desk, the sound waves propagate in the wood and can act like a loudspeaker. In these cases, try to isolate the drive from the console if possible. For example with a rubber mat or a vibration dampening pad.

The further away you can move the drive from your work environment, the less likely it is that noise from it will be a nuisance. If this is limited by the original cables, longer ones are generally available.

Stacking drives is not recommended as this combination can increase noise levels.

Unexpected noises

Below are HDD sounds that are abnormal and are possible signs of a problem. If you hear these noises from a hard drive, immediately check that you have a full backup of all important data on the hard drive:

If you hear a grinding or scraping noise coming from the drive, depending on the severity, it may indicate that continued use will cause physical damage to the hard drive’s platters and put the data at risk. Consider contacting Data Recovery Services for the best next steps.

While all spinning drives introduce some level of vibration, a failing drive can experience exaggerated and abnormal vibration. If possible, compare multiple drives to establish a normal vibration baseline. Also look for irregularities in the vibrations. A healthy drive emits a mild and regular whirring sound.

As mentioned above, a single hard click can mean the heads are being parked. However, if a hard clicking persists or is accompanied by a repetitive clanking (or grinding) noise, there is likely a physical problem with the drive. If possible, compare to other drives that are known to be good.

As mentioned earlier, when an external hard drive has its own power supply, it is normal for a slight hum to come from it. If the hum is severe or there is occasional crackling, the power supply may not be providing enough power to the drive. Another indication is that the drive will no longer spin up (no whirring or vibrating) and some models will also emit an intermittent but regular beeping sound.

External hard drives only beep when there is a problem. In most cases, a single intermittent beep means the drive isn’t getting enough power. If it has its own power supply, test it with another compatible power supply. If the device is powered by USB or another interface, try using a different cable, port, or computer as this could mean that the interface cable is defective. For information about other types of beeps and what they mean, see the user manual for the specific drive model.

Troubleshooting a drive that is making unexpected noises

Hard drives, like all electronic and mechanical devices, can die for many reasons. Unless you’re a hardware engineer or a tech-obsessed geek, you’re probably more concerned with getting your precious files back than figuring out the exact cause of your hard drive’s demise. This guide will help you with that. We’ll walk you through a hypothetical dead hard drive recovery scenario and show you in detail what you need to do.

How a hard drive becomes dead or damaged

Unlike solid-state drives, which use memory cells, hard drives use rotating magnetic platters to store your data. A head moves across the platters to locate where data is stored so it can be read by your system. Suffice it to say that there are many moving parts.

Here are some reasons why a hard drive can become dead or damaged:

Physical Damage – Since hard drives are made up of moving parts, physical damage can easily render your hard drive unusable if one of the platters inside becomes misaligned or scratched.

– Because hard drives have moving parts, physical damage can easily render your hard drive unusable if one of the platters inside becomes misaligned or scratched. Data Corruption – Corruption is a form of logical corruption. Individual files as well as the entire file system can be damaged. When a file system becomes corrupt, your hard drive doesn’t know how to access your data, making it unreadable.

– Corruption is a form of logical damage. Individual files as well as the entire file system can be damaged. When a file system becomes corrupt, your hard drive doesn’t know how to access your data, making it unreadable. Malware Attack – Like viruses, malware comes in many forms. In some cases, it can attack your files or format your entire drive. One such example is Annabelle ransomware virus that can encrypt your files and lock your PC.

Your chances of healing depend on the type of damage and its extent. Some damage can be repaired relatively easily, while in other cases recovery may be impossible.

Before we begin: steps to recover deleted files from dead hard drive

Before looking for ways to recover data from your dead or damaged hard drive, there are two preliminary steps you need to take to prepare the hard drive for recovery.

Step 1: Connect your dead hard drive to a PC

If you have two hard drives in your laptop or computer – perhaps one for your operating system and one for your files – you can safely skip this step. However, if the dead hard drive contains your operating system or it was given to you by a friend or relative, you need to connect it to a working computer.

Desktop PC owners can open the case and connect the damaged hard drive using a SATA cable, which is a computer bus interface that connects host bus adapters to mass storage devices. You can purchase a SATA cable either online or at your local hardware store. One end of the cable goes to the hard drive and the other to the motherboard. There’s really no way you can hook it up wrong, so don’t worry.

Laptop owners can purchase an external USB cradle that is suitable for all common hard drive types. The advantage of such a cradle is its convenience. The hard drive simply slides in and the mount itself connects to your laptop with a standard USB cable.

Step 2: Assessment of the damage

If the failed hard drive is connected to a working computer, you have everything you need to assess the extent of the damage. In some cases, the hard drive will show up as another storage device and you can transfer all files from it.

This may be due to the fact that it is not the hard drive that is defective, but the operating system installed on it. Unfortunately, most data recovery cases are not that simple. The contents of the hard drive are often visible, but Windows or Mac OS X cannot transfer data from it. Worse, the hard drive appears to be empty. So what you need is a data recovery software solution designed for such scenarios.

Step 3: Recover files from dead hard drive with Disk Drill

When all else fails, Disk Drill comes to the rescue. In the vast sea of ​​file recovery programs and apps, Disk Drill stands out with its polished user interface that allows anyone to recover files from external hard drives or SD cards or pretty much any other storage device in just a few minutes.

Free data recovery

Your Deleted File Recovery Companion Free Download

How to recover deleted data from a damaged hard drive:

Download and install Disk Drill on your computer. Select your hard drive and click “Recover” button. preview files. Choose and save your files.

In fact, it only takes a few seconds to tell Disk Drill what to do, followed by a brief wait while the program applies its advanced data recovery algorithms to recover over 400 file types, giving you the freedom to choose what to recover and what you want do not need.

Other Methods to Recover Deleted Files from Dead Hard Drive

There is never a 100% guarantee of recovery. However, there are many different solutions that you can try to get your data back. Let’s start with the simplest method and work our way down.

Method 1: Check the Recycle Bin

The first place to check is the Recycle Bin. When a file is deleted, it is moved to the Recycle Bin instead of being permanently deleted immediately. The only time it doesn’t is when the recycle bin is full or the file is too big to send there. Therefore, before proceeding to the next methods, make sure to check your Recycle Bin by following the steps below.

Open the Recycle Bin on your desktop. Right-click your file and choose Restore. If you are restoring multiple files, hold CTRL and click each file before right-clicking.

When you click Restore, your files will be restored to their original locations. Alternatively, you can drag the files from the Recycle Bin to a location of your choice. If your files could not be retrieved from the recycle bin, try the next method.

Method #2: Restore from a backup

Restoring from a backup is the easiest way to recover your data. Of course, this is only possible if you have a backup from which to restore the data. Windows equips you with the backup utilities to back up your data from the start, but they must be configured first. One such tool is File History, which takes snapshots of your files and allows you to restore a working version of them.

If you had File History turned on, follow these steps to restore a copy of your files.

Navigate to the folder that used to contain the files. On the Home tab, click History. Use the navigation arrows to navigate to a point in time when the files were in the folder. Select the files you want to recover and then click the green recover button. After restoring, you will find the files back in the folder.

How to repair a corrupt, damaged or dead hard drive

While some types of damage can leave your hard drive in a state beyond repair, some damaged, damaged, or dead hard drives can actually be recovered. Once you’ve recovered your data from the drive, try some of the solutions below to see if they can be fixed.

Method 1: Repair with CheckDisk

CheckDisk is a file system repair program that you can use to repair logical errors on your drive. You can use parameters to tell CheckDisk to scan your drive for errors and fix them automatically. This includes the ability to locate bad sectors and mark them as unavailable space so no data is accidentally saved there.

Follow these steps to repair a drive’s file system with CheckDisk.

Right-click Start and select Windows PowerShell (Admin). Click Yes when prompted by UAC. Type chkdsk /f /r D: Replace D: with the letter of your own drive. Press enter.

It doesn’t take long after running the command (longer drives may experience longer wait times). Check if the damage is fixed once the process is complete.

Method #2: Repair corrupt Windows files

If any of your Windows files have become corrupted or missing, it can cause your system to not run properly. In such cases, you can use the System File Checker (SFC) utility. Like CheckDisk, the SFC utility is another tool included with Windows. But instead of fixing file system related issues, it can scan for missing or corrupted Windows system files and restore them.

Use these instructions to restore corrupted or missing Windows files using SFC:

Right-click Start and select Windows PowerShell (Admin). Type DISM.exe /online /cleanup-image /restorehealth and press Enter. It takes a few minutes. This command uses Windows Update to get the files used to fix corruptions. Type sfc /scannow and press Enter. This command will scan all system files and replace any corrupted versions with working versions.

Method #3: Scan for viruses

As mentioned earlier, viruses can be the cause of the damage your drive has suffered. Scanning your drive for viruses can be the solution to get it working again. If you don’t have an antivirus program installed, you can use Windows Security.

Follow these instructions to use Windows Security to scan your drive for viruses.

Press Windows Key + S and locate Windows Security. Open it. Click Virus & Threat Protection. Click Scan Options. Choose your scan type. A full scan is most effective. When you’re done, click Scan Now.

Conclusion

If your hard drive has problems, it doesn’t necessarily mean the end. Many logic problems you encounter are easy to fix once you know what to do. However, physical damage can prove to be more of a problem.

If your drive has been physically damaged and all of the methods in this article have failed, you should contact a data recovery center to have a professional check what other options are available.

FAQ

Data loss is a stressful experience that affects most of the people living the digital lifestyle. There are several scenarios where you might accidentally delete files or unintentionally empty your PC Recycle Bin.

With data recovery software like Disk Drill, you can recover all lost files and a significant portion of formatted data from your crashed hard drive. Disk Drill is hard drive data recovery software that facilitates easy recovery of your only copies of important documents, task files, treasured photos, videos and other related data lost from your device’s internal and external storage.

Data Loss Scenarios: How They Happen and What You Can Do

There are several instances where you may experience data loss from your crashed hard drive.

Typically, you may lose data due to physical damage to your hard drive or logical data loss process. Most physical damage scenarios are irreversible and may require professional help from a hard drive recovery service like Salvagedata. However, data loss scenarios that are not caused by physical damage can be easily recovered with hard drive data recovery software.

Logical data loss concerns files lost due to a formatted hard drive or accidental deletion. In such a situation, your hard drive loses the reference to where the files are located, but they still exist on your PC’s hard drive.

The most common mistake most people make is emptying or emptying the recycle bin. This action completely removes the computer reference to the location of the files.

Causes of Hard Drive Crash and What Can You Do?

Some notorious culprits behind hard drive crashes are:

🥵 Device Overheating – Laptops and PCs tend to overheat when running too many tasks at the same time, using heavy software or applications, or due to excessive usage, etc.

– Laptops and PCs tend to overheat when running too many tasks at the same time, using heavy software or applications, or due to excessive usage, etc. 🔌 Power Fluctuations – Sudden power surges or blackouts can cause serious damage to electrical equipment. Be it a thunderstorm or an unexpected power outage; These situations can lead to hard drive corruption or even crash.

– Sudden power surges or power failures can cause serious damage to electrical equipment. Be it a thunderstorm or an unexpected power outage; These situations can lead to hard drive corruption or even crash. 🔩 Hardware Damage – Physical damage to hard drive from improper device handling or unforeseen accidents can lead to fatal hard drive damage.

– Physical damage to the hard drive due to improper handling of the device or unforeseen accidents can lead to fatal damage to hard drives. 🔧 Wear and tear – All devices have a limited lifespan. Even if you take good care of your computers to increase this number, it will eventually catch up. Regular everyday use would inevitably result in system slowdowns, signs of failing health, or even a hard drive crash.

Apart from these reasons, hard drive crashes can also occur due to manufacturing errors, system errors or malware attacks. In such cases, you may experience humming noise from the drive, persistent error messages, or inconsistent computer behavior. These are all signs of a failing hard drive.

If you are faced with such a situation, make sure to stop using the device immediately. Another common mistake most people make is emptying or emptying the recycle bin. This action completely removes the computer reference to the location of the files. Instead, start data recovery as soon as possible using one of the methods mentioned below.

Recover data from damaged or crashed hard drive with software

Sometimes you accidentally format your hard drive only to find that you have deleted important files and documents. This situation can occur when a hard drive or drive has crashed and your computer prompts you to format the drive, only to find that all files have been lost.

Disk Drill is a data recovery tool that facilitates easy recovery of your only copies of important documents, task files, treasured photos, videos and other related data lost from a variety of storage devices. It is an effective and economical solution with a straightforward user interface for beginners.

💯 With Disk Drill, you can recover all lost files and significant portion of formatted data from your crashed hard drive. Besides that, it offers several additional features like data backups, partition recovery and S.M.A.R.T disk health monitoring, which further protect all your data.

My raw footage hard drive failed for some reason, which included everything I did for my course. It took days but @Cleverfiles Disk Drill saved the day 100%.

This isn’t an ad, just glad to have my stuff back – I’ve tried everything else to no avail! — Tom Buck (@sodarntom) April 10, 2021

There is an unlimited number of file types Disk Drill can recover. What matters most when retrieving data is the type of recovery option available for that particular volume.

Steps to recover data from a damaged or crashed hard drive

Download and install Disk Drill for Windows or Mac OS X. Launch Disk Drill recovery software, select the crashed hard drive and click:

Windows version – Scan for lost data button. Mac version – Restore button. Preview files found with Quick or Deep Scan. Disk Drill provides you with a complete disk scan report at the end of the recovery operation. The report contains a list of all full and partial files found.

🔎 Disk Drill also allows you to filter the scan results and even provides a full disk scan report at the end of the recovery process. Click Recover to recover your lost data. Its speed and simplicity, the features are exceptional, there is no complicated interface, just a click of a button and the files will be recovered over time.

Windows version Mac version

Recover data with a hard drive data recovery service

If your hard drive is damaged beyond the capabilities of data recovery software, you can still recover your information with the help of a data recovery service. SalvageData Recovery Service is an excellent solution when you are faced with a corrupted or damaged hard drive. Their technical expertise can recover data from badly damaged drives and recover files you thought were lost forever.

Use the following steps to hire SalvageData Recovery Service to salvage your valuable data:

Start a work order or contact SalvageData Recovery Service for a free estimate. Ship your device to SalvageData or drop it off at one of their nationwide locations. Be sure to pack the drive securely to avoid static electricity, shock, and vibration. After an evaluation of the device by the SalvageData team, you will receive a free bug report and a guaranteed price quote. Recovery will only be initiated after customer approval and authorization. If your data cannot be recovered, there are no costs. When the successful recovery is over, your data will be returned on a hard drive or flash drive or external HDD/SSD.

Recover data with Disk Management utility

If your hard drive is logically damaged, chances are you can recover your data using in-computer techniques. If your drive is crashed or damaged, your data may become inaccessible. You can use Disk Management utility on both Windows and Mac to fix this problem and access this data.

Follow these steps to recover your files using Disk Management utility:

On Windows:

Press Windows + X and select the Disk Management option. Locate the crashed hard drive in Disk Management.

If the disk is visible, you can format it to fix errors and make the data accessible.

⚠️ Attention! Using this method to recover a logically damaged hard drive may result in losing your data permanently. Make sure you keep backup copies of your data or turn to professional data recovery software to recover your files.

On Mac:

Open Disk Utility from Spotlight (press Command + Spacebar ). Select the disk or volume in question, and then click First Aid.

After running First Aid, you’ll know if Disk Utility found or fixed any problems.

Once the process is complete, your hard drive will be repaired and ready to use!

Recover data using CMD prompt

CMD or Command Prompt is another method that can be used to fix corrupted or crashed hard drive issues. Although it may seem a bit technical, run CHKDSK command on your PC to fix issues without formatting your drive.

Here is how you can run CHKDSK command and fix your hard drive:

Press Win + X , select Command Prompt (Admin) option. Type chkdsk and press Enter to analyze the errors on your corrupt hard drive. Type chkdsk C: /f /r/x to repair the drive.

Insight – Here C is the drive letter of your damaged hard drive.

Tips to avoid data loss from a hard drive

Here are some tips to help you avoid data loss from a hard drive.

Stop using the device if you hear strange noises such as clicking or grinding noises. Before you stop using the device, you should consider using Disk Drill’s byte-level backup feature to create a usable backup that includes deleted files.

if you hear strange noises such as clicking or grinding noises. Before you stop using the device, you should consider using Disk Drill’s byte-level backup feature to create a usable backup that includes deleted files. Use antivirus software to keep your computer free from malware. Many virus and malware infections attack your computer and can lead to data loss.

to keep your computer free from malware. Many virus and malware infections attack your computer and can lead to data loss. Back up your data regularly to protect your information. This allows you to recover most or all of your data without special software or hiring a recovery service.

often to protect your information. This allows you to recover most or all of your data without special software or hiring a recovery service. Keep the storage device away from extreme heat or high humidity, as these conditions can cause damage.

away from extreme heat or high humidity, as these conditions can cause damage. Review any potentially destructive activity such as deleting files or formatting a partition to ensure you have the correct information. Carelessness can lead to unintentional data loss that could have easily been avoided.

Conclusion

When you face data loss on a device that is still in use and can be detected by your operating system, your first option should be to use Disk Drill data recovery software. It is a reliable and easy-to-use solution that allows you to recover your data in a few clicks. If your data can be recovered via software, Disk Drill will do it.

In cases where the drive is corrupted and your system cannot access it, a software solution is not enough. You must use a reputable recovery company like Cleverfiles Data Recovery Service. Whatever kind of data loss problem you have, Cleverfiles experts have a solution.

FAQ

http://www.groovypost.com

At some point, technology can and will let us down. Therefore, we should regularly implement backup strategies to protect our data. We store a lot of important information on our computers and devices; Documents, photos and videos. Windows includes a variety of solutions to make backing up your data easier. Whether backup and restore, system imaging, file history or OneDrive. But what should you do if your computer won’t boot?

Recover data from non-booting hard drive

If you cannot start Windows successfully, you can try to perform a custom installation and recover your data from Windows.old. However, if you don’t have a working optical drive or USB flash drive, you can put the hard drive in an external hard drive enclosure, connect it to a working computer, and copy your data.

Get an external hard drive enclosure

This is the first thing you must have. They are inexpensive and can be used with an existing hard drive as an external storage device. An enclosure is basically an enclosure that protects the drive and allows you to connect it to a USB, FireWire, or eSATA port. You can buy a case from Amazon for between $20 and $50. They are available in 3.5 inch (standard desktop) or 2.5 inch (notebook) sizes. Make sure you select the correct internal interface – IDE/ATA or SATA depending on the type of drive you are using.

Uninstall the non-booting hard drive

You must remove the hard drive from the system unit to install it in the external enclosure. The process varies by build, model, and form factor. Check the manufacturer’s documentation that came with your computer or visit the manufacturer’s website. Some are simple, requiring only depressing a locking mechanism to release the hard drive from its drive bay.

Other configurations may require the removal of a mounting mechanism, particularly if the drive is 2.5″. Be prepared to have essential tools like a Torx 5 point screwdriver and a flat head screwdriver. If you plan on building your own computers or doing these types of repairs, you often get a decent set of tools in a computer repair kit.

This particular configuration uses a 2.5″ drive on a 3.5″ bracket. You’ll also notice the green latch mechanism to release the drive from its base.

Install the hard drive in the external enclosure

Installing it in the case should be easy. Depending on the case you buy, you may need to make some manual adjustments. Some may require you to insert the drive and that’s it. In the image below, the external enclosure requires the SATA cables to be manually connected to the drive. As you can see in the image above, this external enclosure also supports PATA drives. After you have installed and securely connected the drive, you can insert it into the protective case.

Connect USB and power cables

The next step is to connect the drive to your computer, which is the same as connecting a regular external hard drive. Once the drive is powered on, Windows will automatically detect and install the drive. You will either be prompted to search for it or you can access it through File Explorer.

restore the data

Since the installation on the drive still protects the folders containing your data, you will get an error message if you try to open and browse the folder. Click Next and enter your admin password (if required). [If you have trouble with this step, this article may help]

Now you can browse the user folder and continue copying your data.

Once you are sure that you have recovered your data from the hard drive, you can format and repartition the hard drive if you wish. Remember to browse the common locations where data is stored, e.g. B. Your user folder C:\Users and C:\Users\Public. If you have unstructured information such as sticky notes, you can also find them at: C:\Users\youraccountname\AppData\Roaming\Microsoft\Sticky Notes, copy the StickyNotes.snt file to the appropriate directory.

Seagate hard drive is one of the most popular types of hard drive and hence we receive many questions about Seagate hard drive repair methods. A hard drive is prone to many types of errors that can disrupt your workflow. So, we tried to answer different types of “How to fix Seagate hard drive?”. Any questions about this article.

If your Seagate hard drive is not recognized in Windows or you encounter beeping issues with your hard drive, just go through this article and find the Seagate hard drive repair method that suits your needs.

Part 1. How to Fix Seagate Hard Drive Not Detected Issue?

Is your hard drive not recognized by Windows? Don’t worry, this is a kind of problem that is very common when you use an external hard drive. The situation is similar with a Seagate hard drive. Such problems can occur with your Seagate hard drive when your hard drive is connected to PC but not recognized. Below are the different methods to fix your Seagate hard drive not recognized by your system.

Method 1. Change the port

It is an obvious method and also the most effective to fix Seagate hard drive. Most of the time, when your Seagate hard drive is not recognized by Windows, you think that there is some problem with your hard drive and you try to perform a specific type of Seagate hard drive repair. But it can also be a problem with your USB port. Therefore, the first thing you should try is to connect the hard drive to a different port and see whether the hard drive is recognized or not.

Method 2. Show All Hidden Devices

Step 1 After connecting your Seagate drive to your PC, go to the search box on the home screen and type “Device Manager”. In the Device Manager results, click “Enter” to bring up the Device Manager window.

Step 2 In the Device Manager window, you can see the “View” option on the top menu bar. Click View, then click Show Hidden Devices. Now in the Device Manager window, go to “Disk Drivers” and expand the option.

Step 3 If your drive is hidden on your system, it will be highlighted among other hidden drives. Right-click on the hidden drive and select “Uninstall”. This will uninstall the drive from your system. Now unplug and plug back the Seagate drive to see if your Seagate drive is fixed or not.

Part 2. How to Fix Seagate Hard Drive Beeping Issue?

Sometimes your Seagate hard drive encounters beeping issues or you may hear a clicking sound from your Seagate hard drive. This type of problem is uncommon with hard drives, but it’s not a big problem. You can try any of the Seagate hard drive fixes mentioned below to fix this problem.

Method 1. Use a different cable or port

Most of the time, a Seagate hard drive beeps due to failed connection. If the connection between your Seagate external hard drive and your system is not properly established, you may hear a beeping or clicking noise from the hard drive. To fix your Seagate hard drive, just try connecting your hard drive to a different port on your system. Or you can also try another compatible USB cable to see if there is a problem with the hard drive connection.

Method 2. Clean the ports and drive

There have been many such cases where the Seagate hard drive beeped because either the hard drive’s connectors were not clean or the system’s connectors were dusty. To fix Seagate hard drive, you need to first shut down your system and unplug the power and also disconnect the hard drive. Now use a compressed air stick and blow out all the dust from your hard drive, from the drive’s connectors, from your system’s connectors and from all the organs of your system. Now reconnect your Seagate hard drive to see whether Seagate hard drive is fixed or not.

Method 3. Check your hard drive with CMD

If you are not sure why your Seagate hard drive is beeping and you need to fix your Seagate hard drive, you can try this method. This method uses a command that scans your selected hard drive for such errors and informs you if your Seagate hard drive has any error.

Step 1 First, connect your Seagate external hard drive to your system using a compatible cable. Once connected, make sure your system successfully identifies the drive.

Step 2 Now from the home screen of your system, go to the search box and type “CMD” to see “Command Prompts” in the results. Click Command Prompt to bring up the CMD window.

Step 3 Once you are in the CMD panel, type the command “chkdsk #:/r” and press Enter. The system will process the command and scan and examine your hard drive for errors or bad behavior.

Note: The “#” in the step 3 command refers to the “drive letter”, replace the “#” with the drive letter you want to perform this action on.

Once the command has been processed and your drive has been examined, the system will tell you whether there is a bad behavior problem with your drive or not.

Part 3. How to Fix Bad Sectors on Seagate External Hard Drive?

The bad sectors problem on your hard drive should be fixed as soon as possible as it may endanger your data stored on your hard drive. This problem occurs on your Seagate hard drive mainly due to the system crash or other software errors. You can try the methods below to fix the bad sector on your Seagate external hard drives.

Method 1. Use the built-in error checking utility on Windows

Step 1 Once you have connected your Seagate external hard drive to the system, go to “This PC”. Once you are in This PC, navigate to your connected Seagate hard drive that you want to repair and right click on it.

Step 2 Go to “Properties” in the right-click menu and then go to the “Tools” tab in the “Properties” dialog box.

Step 3 Once inside the Tools tab, you will see the Check button under the Error Checking section. Click on “Check” option to continue to repair Seagate hard drive.

Step 4 You will see a Check Disk dialog box when Windows finds an error on your hard drive. Now in the dialog box, select the option “Fix system errors automatically” to proceed to repair Seagate hard drive. Proceed to “Scan for bad sectors and attempt recovery” option and then click “Start”.

Note: The “Fix system errors automatically” option only appears when Windows finds an error with the Seagate drive in your system.

Once the process is over, you can check whether your Seagate hard drive bad sectors are fixed or not. If it is not fixed, you can try the same method again.

Method 2. Use Seagate SeaTools for Windows

If you are using a Seagate hard drive, you may know that Seagate provides a Seagate hard drive repair tool. With this tool, you can detect bad sector problems or many other problems with your hard drive and fix such problems.

The Seatools can be used on your Windows operating system. However, it does not support all types of hard drives, it is specially configured to repair Seagate hard drives.

Bonus Tips: How Do You Keep Your Seagate External Hard Drive In Good Condition?

If you want to use your Seagate hard drive for a long time and keep it in good condition, then you need to take care of your hard drive. Below are some tips that can help you keep your hard drive in good condition.

Position it well

When using Seagate external hard drive, it is better if you are a little careful. Because you may never know what could harm him. When using the hard drive, make sure it is always placed on a flat surface that is free of bumps or other things that can physically damage it. Also, do not store it near a heater or other device that may increase the temperature of the drive. Always leave the drive open during use, do not cover it with anything that might contain the internal heat. Keep a backup

Sometimes you need to format your Seagate external hard drive to boost its performance or make it error-free. However, if you don’t have a backup of your data stored on the drive, it becomes difficult for you to perform certain tasks to fix or keep your Seagate external hard drive intact. So always keep a backup of your hard drive. Protect it from extreme temperatures

The circuits in your external hard drives are very delicate, and even a small drop or rise in temperature can damage them. So if you expose your Seagate hard drive to direct sunlight for a long period of time or store it in a cool place, it will lose its integrity and probably your data as well. Moisture and dust also have the same effects on your hard drive, so always keep your hard drive covered when not in use. Only connect it to trusted devices. You should avoid using your Seagate external hard drive or any external hard drive with a public system or a system that is not protected from viruses or malware. Using your hard drive on such systems can jeopardize all your data and the condition of your hard drive.

Conclusion:

You can use any of the above methods to fix your Seagate hard drive. Any of your hard drives or your Seagate hard drive can face many such errors. Hence, we have discussed different types of Seagate Drive repair methods to help with different types of problems.

Here are the most common causes of hard drive clicking (not beeping) and what you can do to properly troubleshoot the issue.

There are a handful of reasons you may be hearing this noise from your hard drive.

If you have an older hard drive, then it is most likely a hardware issue. However, if you have a newer one, it can be either hardware or software.

Regardless, you should determine the root cause of the problem before it leads to data loss.

Most of the time, the clicking sound comes from an actuator arm that isn’t working properly.

These are the main causes of a clicking drive:

physical damage

This is one of the most common culprits. Have you recently dropped your external drive? Or was it exposed to extreme heat or cold in any way?

If your hard drive has been dropped, exposed to fire, or water spilled on it, it may click.

wear and tear

Hard drives don’t last forever. If you’ve had a hard drive for years and it recently started clicking, then it could just be failing. Just like a car engine that eventually gives up the ghost, so can a hard drive.

Usually this happens when the actuator arm is worn and not working properly.

electrical problems

Sometimes your hard drive does not get enough power due to a defective power supply unit. If you have an alternate power source, you can test it to see if it’s causing the clicking. These problems can also be caused by power surges and thunderstorms. Your hard drive circuit board could also be a related issue.

Read/write head misalignment

If the read/write heads are not aligned due to dropping or poor handling of your hard drive, you will hear the hard drive click.

Problem with the service area

There is a part of your hard drive that stores manufacturer data, this area is called the service area. If this becomes damaged, your hard drive will no longer function properly. The actuator arm swings back and forth trying to find the information, resulting in the click you hear.

Damaged turntable

If the platter is damaged, the actuator arm will not work properly. It will attempt to locate the platter and oscillate back and forth, resulting in a clicking sound.

manufacturer error

Many hard drives fail due to manufacturing defects, faulty parts, or firmware issues. If you have a relatively new hard drive that hasn’t suffered any damage, this could be the problem. This is usually covered by the manufacturer’s warranty, but they only cover the drive, not the data on it.

signs of failure

There are a few ways to determine if your hard drive isn’t working properly. The most obvious is the clicking sound emanating from your drive.

However, there are other signs to look out for:

Repeated clicking noises from your hard drive (this indicates mechanical damage)

A message stating that the operating system cannot be found

Your hard drive is not recognized when you start your computer

Your hard drive is silent and does not make any noise

It takes a long time to access your files (this indicates data corruption)

Your system will keep rebooting or you will be greeted with the “Blue Screen of Death”.

When you mount the drive, the computer will prompt you to format the drive

Your hard drive is not recognized when plugged in (USB or external hard drive)

If you experience any of the above signs of failure, you should stop using your hard drive and consult a hard drive repair professional as soon as possible.

how to repair

Unless you are an experienced technician with the right know-how, it is not recommended to repair your hard drive yourself. This usually leads to further damage up to and including permanent data loss.

That being said, it might be a minor issue and the issue can be resolved with a few quick fixes.

One thing to check is the power source. You may have an outlet that is overloaded and cannot provide enough power. You can also try replacing the power cord as it may not be working properly and may need to be replaced.

Aside from these simple repairs, your hard drive should be in the hands of a hard drive recovery expert.

A hard drive has very delicate internal components and can be easily damaged through the use of improper tools or an unclean environment. Your data is at risk the moment the internal platter or hard drive head is exposed to dust and dirt.

what not to do

It can be tempting to try and diagnose and fix your hard drive problem yourself. While Google is great for many things, it’s not the best for troubleshooting complex hardware issues.

Here are some common hard drive repair myths that won’t do you any good.

Cool your hard drive in the freezer

Putting your hard drive in the freezer can help constrain the mechanics. However, this is a very outdated technique. Once it thaws and heats up, it will corrode the drive and electrical components. User recovery software for a hardware problem

Oftentimes, the clicking sound of your hard drive indicates a mechanical or physical problem, so running software won’t fix the problem. Continued operation of the drive will only cause more problems. Including running your own data recovery software. Open the drive itself

Attempting to open the drive and fix the clicking yourself can completely damage the drive. Repairing the read/write heads requires a clean room setup, without which you run the risk of dust and other debris damaging your existing data.

How to recover data

If you hear your hard drive clicking or making other noises, you should contact a data recovery expert immediately.

This isn’t the kind of problem that gets better on its own. Aside from a bad power connection, almost every other problem is related to the inner workings of your hard drive. Attempting to open your hard drive yourself can result in complete hard drive failure.

When your hard drive clicks, the physical damage has already been done. This most likely cannot be replaced.

However, you can still get your data back. While it can be tempting to run your own backup or restore programs, doing so can put your drive at further risk. Continued operation of your hard drive can add to the damage.

If you try to repair your hard drive yourself or run a data recovery program while your hard drive is clicking, you risk losing all your data. Forever.

Your data is not worth the risk. Contact a data recovery specialist today to determine the best plan for the future.

When your hard drive crashes and stops working, it can be a nightmare. Whether your personal files are lost or your business data is at stake, you’re probably thinking: How much will data recovery cost me?

This page is intended for those who want to learn more about all aspects that might play a role in determining the cost of data recovery. Although a home remedy might work for some data loss situations, we believe a specialist should recover your corrupted files. Specialists have the greatest expertise and knowledge to ensure a higher chance of successful data recovery.

We’re going to make it clear what you should expect from a data recovery company, whether you choose Proven Data or another credible data recovery company.

As a data recovery service provider since 2011, we have witnessed data loss scenarios affecting both home computer users and large corporations. With thousands of successful data recovery cases under our belt, we understand that there can be confusion as to how a data recovery company quotes your failed storage media. Losing access to valuable personal memories or business-critical data can be devastating and leave you with a sense of insecurity, especially when you can’t see the cost up front.

The data recovery industry is notorious for hiding its prices and not providing a transparent pricing structure. A trustworthy data recovery company should have an experienced data recovery technician on call to clear up any pricing confusion.

We are here to enlighten and show how to calculate data recovery cost if you decide to proceed with data recovery services and the cost you will incur for do-it-yourself data recovery. The tariffs and costs listed on this page apply to data carriers such as:

Seagate hard drive is one of the most popular types of hard drive and hence we receive many questions about Seagate hard drive repair methods. A hard drive is prone to many types of errors that can disrupt your workflow. So, we tried to answer different types of “How to fix Seagate hard drive?”. Any questions about this article.

If your Seagate hard drive is not recognized in Windows or you encounter beeping issues with your hard drive, just go through this article and find the Seagate hard drive repair method that suits your needs.

Part 1. How to Fix Seagate Hard Drive Not Detected Issue?

Is your hard drive not recognized by Windows? Don’t worry, this is a kind of problem that is very common when you use an external hard drive. The situation is similar with a Seagate hard drive. Such problems can occur with your Seagate hard drive when your hard drive is connected to PC but not recognized. Below are the different methods to fix your Seagate hard drive not recognized by your system.

Method 1. Change the port

It is an obvious method and also the most effective to fix Seagate hard drive. Most of the time, when your Seagate hard drive is not recognized by Windows, you think that there is some problem with your hard drive and you try to perform a specific type of Seagate hard drive repair. But it can also be a problem with your USB port. Therefore, the first thing you should try is to connect the hard drive to a different port and see whether the hard drive is recognized or not.

Method 2. Show All Hidden Devices

Step 1 After connecting your Seagate drive to your PC, go to the search box on the home screen and type “Device Manager”. In the Device Manager results, click “Enter” to bring up the Device Manager window.

Step 2 In the Device Manager window, you can see the “View” option on the top menu bar. Click View, then click Show Hidden Devices. Now in the Device Manager window, go to “Disk Drivers” and expand the option.

Step 3 If your drive is hidden on your system, it will be highlighted among other hidden drives. Right-click on the hidden drive and select “Uninstall”. This will uninstall the drive from your system. Now unplug and plug back the Seagate drive to see if your Seagate drive is fixed or not.

Part 2. How to Fix Seagate Hard Drive Beeping Issue?

Sometimes your Seagate hard drive encounters beeping issues or you may hear a clicking sound from your Seagate hard drive. This type of problem is uncommon with hard drives, but it’s not a big problem. You can try any of the Seagate hard drive fixes mentioned below to fix this problem.

Method 1. Use a different cable or port

Most of the time, a Seagate hard drive beeps due to failed connection. If the connection between your Seagate external hard drive and your system is not properly established, you may hear a beeping or clicking noise from the hard drive. To fix your Seagate hard drive, just try connecting your hard drive to a different port on your system. Or you can also try another compatible USB cable to see if there is a problem with the hard drive connection.

Method 2. Clean the ports and drive

There have been many such cases where the Seagate hard drive beeped because either the hard drive’s connectors were not clean or the system’s connectors were dusty. To fix Seagate hard drive, you need to first shut down your system and unplug the power and also disconnect the hard drive. Now use a compressed air stick and blow out all the dust from your hard drive, from the drive’s connectors, from your system’s connectors and from all the organs of your system. Now reconnect your Seagate hard drive to see whether Seagate hard drive is fixed or not.

Method 3. Check your hard drive with CMD

If you are not sure why your Seagate hard drive is beeping and you need to fix your Seagate hard drive, you can try this method. This method uses a command that scans your selected hard drive for such errors and informs you if your Seagate hard drive has any error.

Step 1 First, connect your Seagate external hard drive to your system using a compatible cable. Once connected, make sure your system successfully identifies the drive.

Step 2 Now from the home screen of your system, go to the search box and type “CMD” to see “Command Prompts” in the results. Click Command Prompt to bring up the CMD window.

Step 3 Once you are in the CMD panel, type the command “chkdsk #:/r” and press Enter. The system will process the command and scan and examine your hard drive for errors or bad behavior.

Note: The “#” in the step 3 command refers to the “drive letter”, replace the “#” with the drive letter you want to perform this action on.

Once the command has been processed and your drive has been examined, the system will tell you whether there is a bad behavior problem with your drive or not.

Part 3. How to Fix Bad Sectors on Seagate External Hard Drive?

The bad sectors problem on your hard drive should be fixed as soon as possible as it may endanger your data stored on your hard drive. This problem occurs on your Seagate hard drive mainly due to the system crash or other software errors. You can try the methods below to fix the bad sector on your Seagate external hard drives.

Method 1. Use the built-in error checking utility on Windows

Step 1 Once you have connected your Seagate external hard drive to the system, go to “This PC”. Once you are in This PC, navigate to your connected Seagate hard drive that you want to repair and right click on it.

Step 2 Go to “Properties” in the right-click menu and then go to the “Tools” tab in the “Properties” dialog box.

Step 3 Once inside the Tools tab, you will see the Check button under the Error Checking section. Click on “Check” option to continue to repair Seagate hard drive.

Step 4 You will see a Check Disk dialog box when Windows finds an error on your hard drive. Now in the dialog box, select the option “Fix system errors automatically” to proceed to repair Seagate hard drive. Proceed to “Scan for bad sectors and attempt recovery” option and then click “Start”.

Note: The “Fix system errors automatically” option only appears when Windows finds an error with the Seagate drive in your system.

Once the process is over, you can check whether your Seagate hard drive bad sectors are fixed or not. If it is not fixed, you can try the same method again.

Method 2. Use Seagate SeaTools for Windows

If you are using a Seagate hard drive, you may know that Seagate provides a Seagate hard drive repair tool. With this tool, you can detect bad sector problems or many other problems with your hard drive and fix such problems.

The Seatools can be used on your Windows operating system. However, it does not support all types of hard drives, it is specially configured to repair Seagate hard drives.

Bonus Tips: How Do You Keep Your Seagate External Hard Drive In Good Condition?

If you want to use your Seagate hard drive for a long time and keep it in good condition, then you need to take care of your hard drive. Below are some tips that can help you keep your hard drive in good condition.

Position it well

When using Seagate external hard drive, it is better if you are a little careful. Because you may never know what could harm him. When using the hard drive, make sure it is always placed on a flat surface that is free of bumps or other things that can physically damage it. Also, do not store it near a heater or other device that may increase the temperature of the drive. Always leave the drive open during use, do not cover it with anything that might contain the internal heat. Keep a backup

Sometimes you need to format your Seagate external hard drive to boost its performance or make it error-free. However, if you don’t have a backup of your data stored on the drive, it becomes difficult for you to perform certain tasks to fix or keep your Seagate external hard drive intact. So always keep a backup of your hard drive. Protect it from extreme temperatures

The circuits in your external hard drives are very delicate, and even a small drop or rise in temperature can damage them. So if you expose your Seagate hard drive to direct sunlight for a long period of time or store it in a cool place, it will lose its integrity and probably your data as well. Moisture and dust also have the same effects on your hard drive, so always keep your hard drive covered when not in use. Only connect it to trusted devices. You should avoid using your Seagate external hard drive or any external hard drive with a public system or a system that is not protected from viruses or malware. Using your hard drive on such systems can jeopardize all your data and the condition of your hard drive.

Conclusion:

You can use any of the above methods to fix your Seagate hard drive. Any of your hard drives or your Seagate hard drive can face many such errors. Hence, we have discussed different types of Seagate Drive repair methods to help with different types of problems.

Is it at all possible to recover data from dead external hard drive?

Yes, it is possible to recover data from dead external hard drive. There are options for physical and logical types of disk damage. The key factor of logical damage is to trick your computer to recognize the broken device so that you can use a recovery software to recover files from the dead external hard drive. If the drive stops working, the data stored on it is still intact and can be retrieved with the right tools. Unfortunately, things get complicated with physically damaged drives. But do not despair, the situation may not be as dire as it seems at first glance. Below we will talk about data recovery options for both physical and logical types of malfunctions.

External hard drives are commonly used on Windows systems to provide extended storage capacity to home computers. They’re a great option for storing photos, videos, or any other type of file that you don’t want on your computer’s main hard drive. Sharing data with friends and colleagues is also easily possible with an external hard drive. A single Seagate or Toshiba external hard drive can store terabytes of valuable data.

Unfortunately, external hard drives are not immune to data loss. There are a variety of issues that can cause you to lose data from an external hard drive. Some of them can be easily addressed and you can recover the lost information. In case of dead external hard drive, you may need to hire professional recovery experts to recover your data.

The difference between physical and logical disk corruption

External hard drives are prone to physical and logical damage that can result in loss of some or all of the data on the device. These two different types of damage require different methods when trying to recover your lost files. A dead external hard drive has often suffered physical damage.

Data loss caused by logical damage to an external hard drive can often be recovered using native operating system functions. Data recovery software for personal use can also be used when native methods fail. The recovery software repairs the logical damage and makes the lost files accessible again. To recover from a logical disk damage, the device must be recognized by your operating system.

Physical damage that leads to data loss presents a more difficult recovery scenario. Very often, your operating system cannot access a physically damaged drive, making it impossible to use the same recovery option used for logical damage. In these cases, you must use a professional data recovery service to try to recover your files.

The types of damage caused by common hard drive problems

We’ve compiled a list of common hard drive problems and the types of damage they cause. You can use this list to determine if you can attempt to recover lost data yourself or if you need to hire a recovery service. In all cases of data loss, you should stop using the device on which the lost files occurred immediately to avoid overwriting the information you want to recover.

Accidental file deletion – This type of logical damage does not usually result in a dead hard drive. Data can usually be recovered using operating system functions or data recovery software if you act quickly.

Formatted or Reformatted Drives – If you accidentally format your Western Digital or Samsung external hard drive, you have essentially caused logical damage to the files inside. Fortunately, data recovery software can undo this damage and recover the data from the formatted drive or partition. The key is to stop using the drive until you’ve performed the recovery.

Corrupt File Systems – Corrupt file system is a form of logical damage that can cause your external hard drive to stop working. You may be faced with an inexplicable RAW file system that needs to be recovered. File system corruption can result in a crashed drive that won’t allow you to start your computer. Data recovery software can often fix this type of logical damage.

Mechanical Damage – The mechanical components of an external hard drive can become damaged through mishandling or wear and tear. Before the drive fails, you may hear some strange clicking or grinding noises that indicate the platter is damaged. External hard drives must be handled with care as falling can misalign the platters or read/write heads and render the drive unusable. This type of damage often causes your system to fail to recognize the device. If the drive is not recognized by your system, you will need to use a recovery service to recover your data.

Environment Issues – A dead external hard drive can be caused by leaving the device in the wrong place. Exposing the drive to excessive heat or humidity may result in device failure and large data loss. Damage of this type must be repaired by sending the drive to a data recovery service, where their technicians will attempt to recover the drive’s contents.

Recover data from dead external hard drive with logical damage on Windows

There are several methods you can use on Windows computer to try to recover data from dead external hard drive suffered logical damage. The essential first step is to get the drive recognized by your operating system. Once that is done, you can try these methods to recover data from logically damaged external hard drive.

Try the Windows Recycle Bin

If the problem was simply deleted files, you might find them here.

Use the command prompt

To recover files from a dead disk using Command Prompt, you can try using this command:

Open a command prompt on your Windows computer. Type chkdsk ‘drive letter’: /f and press Enter. Press Y until the command line reappears. Type the drive letter and press Enter. Enter this command: drive letter: attrib –h –r –s /s /d *.*.

Use data recovery software to scan the external drive for logically lost data

Here is a quick overview of how you can do it with Disk Drill data recovery software.

Download and install Disk Drill. Plug in the external drive and launch the program. Click Scan for Lost Data to scan for drive.

Preview the found files and select the ones you want to retrieve.

Click the Restore button to perform the restore.

Related Article Hard Drive Recovery Software: Recover Deleted HDD Data (2021) This all-in-one application allows you to recover files from hard drive in a few simple clicks.

Recover data from dead external hard drive with logical damage on Mac

If you manage to get your external hard drive recognized by your Mac, you can try these methods to recover lost data from the device.

Retrieve the lost files from Recycle Bin. Use a backup to restore your files. Recover your data with data recovery software.

Data recovery software is the best choice to recover your lost files from external hard drive with your Mac or MacBook.

Recover data from dead and physically damaged external hard drive

In cases where the drive is physically damaged and your operating system cannot access it, your options are much more limited. Essentially, your only choice is to enlist the services of a reputable data recovery service. Here’s a quick look at what to expect if you have to go in that direction.

Contact the recovery service for details on how to ship your drive and get a quote for recovering your data. Send the device to the service center. Once it arrives, technicians use special equipment in an environmentally controlled clean room to disassemble and clone the drive so its data can be recovered. When the recovery is complete, your data will be returned and the original device will be destroyed. A reputable company will not charge for a failed recovery.

Backups to the rescue!

A working backup of the data on your external hard drive allows you to get your data back even if all the previous options fail. Backing up your system and data regularly is a computer best practice that all users should follow. A backup may be the only way to recover your data if your operating system cannot see the drive, aside from a data recovery service.

It’s a lot cheaper to restore from a backup than sending your device to the recovery center and paying the fee to get your data back. Backups can’t always restore current data that wasn’t stored on your backup media, but it’s worth protecting your data in this way.

Are External Hard Drives Still Popular in 2021?

External hard drives are still widely used by individuals and organizations to expand the storage capacity of their systems. The enterprise-class external hard drive market is expected to remain strong over the next few years. Solid State Drives (SSDs) are becoming increasingly popular due to their higher speed and lower power consumption. Cloud storage also offers an alternative to external hard drives, but requires an internet connection and enough bandwidth to transfer files.

The market for external hard drives is not going away anytime soon. The devices offer large capacities and are cheaper per gigabyte than similarly sized solid state drives. They are still extremely useful in many scenarios, including:

Securing Your PC – Large capacity external hard drives are perfect for people who want to protect their data. The speed of an SSD is not required in this role.

– Large capacity external hard drives are perfect for people who want to protect their data. The speed of an SSD is not required in this role. Storing Multimedia Collections – Many users have large collections of movies, photos, and music that cannot all be stored in the computer’s internal memory. Using an external hard drive allows a user to store as many large multimedia files as they want and easily transport them for use on another computer.

– Many users have large collections of movies, photos and music that cannot all be kept in the computer’s internal memory. Using an external hard drive allows a user to store as many large multimedia files as they want and easily transport them for use on another computer. Expanding Enterprise Storage Capacities – Banks of external hard drives have their place in an enterprise’s storage hierarchy. In this scenario, data that is used frequently or needs to be accessed quickly can be stored in more expensive flash memory or SSDs. External hard drives handle the overflow data that needs to be available, but can withstand the slower access speed of HDDs.

Did you know?

The first external hard drive was introduced by IBM on September 13, 1956. They were refrigerator-sized units that required air-conditioned rooms to operate. The system, dubbed the IBM 350 Disk File, did not run internally in the computer, hence the naming of an external hard drive. It consisted of a magnetic disk storage unit with its accessor, the electronic and pneumatic controls for the accessor, and a small air compressor.

FAQ

How can I recover data from a hard drive that is not recognized in the BIOS? You need to fix the problem that is preventing the BIOS from detecting the hard drive. The problem is often the cable that connects the external drive to your computer. Try these steps to fix the problem. Disconnect and reconnect the cable.

Try a different USB port.

Swap out cables and use one that you know works.

Go into your system’s BIOS and make sure the device is not disabled there. How do I fix an external hard drive after it’s dropped? After an external hard drive has been dropped and stopped working properly, you can be pretty sure that it has suffered physical damage. If you are not very experienced in hard drive repairs, you should consider sending the drive to a data recovery center and having your files and folders restored. Why is my external hard drive recognized but not opened? There are several reasons why you cannot open an external hard drive that is recognized by your operating system. Power issues can cause a drive to be visible but not used for data access. Try swapping cables or connecting the device to a different port.

A bad USB port can be the problem. Try a different port to see if that resolves the issue.

Driver issues can be the reason your drive won’t open. Updating or reinstalling the drives may resolve the issue.

Restart your computer. As we all know, rebooting often solves strange and inexplicable problems. This could be one of them.

Try the external drive on a macOS computer. It may have been formatted for use with a Mac and therefore cannot be used by your Windows computer.

Conclusion

When using peripheral storage devices, there may come a time when you need to retrieve data from dead external hard drive. Data recovery software like Disk Drill offers a method to recover your files and folders without resorting to an expensive data recovery service. Protecting the data on an external drive should definitely be considered if the information it contains is of any value. It’s never a bad idea to have a second copy of your external hard drive just in case disaster strikes. Make backups and get Disk Drill to keep your data safe.