Top 23 How Do You Reset The Airbag Light On A Chevy Best 131 Answer

You are looking for information, articles, knowledge about the topic nail salons open on sunday near me how do you reset the airbag light on a chevy on Google, you do not find the information you need! Here are the best content compiled and compiled by the Chewathai27.com team, along with other related topics such as: how do you reset the airbag light on a chevy how do you reset the airbag light on a chevy avalanche, how to reset airbag light on chevy tahoe, how to reset airbag light on chevy impala, how to reset airbag light on chevy equinox, how to reset airbag light on chevy cobalt, how to reset airbag light on chevy traverse, how do you reset the airbag light on a gmc sierra, how to reset service airbag light on gmc terrain

First, turn the ignition switch on. Next, wait for the airbag light to turn on – it normally stays lit for seven seconds before shutting itself off. Then, immediately turn off the ignition switch, and wait three seconds. Repeat the initial steps once or twice before starting the engine.It is impossible in most car models to reset the airbag light without a scanner. This is for safety cautions because you should always repair the fault after the airbag light occurred. Luckily, in many car models, the airbag light will also go away by itself if you have repaired the problem.If your airbag has been deployed and has not been properly reset, the airbag light will be on. If the airbag hasn’t been deployed, the light will come on when the system senses that it cannot activate the airbag; this means that there is some sort of a problem with the airbag system in your vehicle.

Contents

Can you reset airbag light without tool?

It is impossible in most car models to reset the airbag light without a scanner. This is for safety cautions because you should always repair the fault after the airbag light occurred. Luckily, in many car models, the airbag light will also go away by itself if you have repaired the problem.

What causes the airbag warning light to come on?

If your airbag has been deployed and has not been properly reset, the airbag light will be on. If the airbag hasn’t been deployed, the light will come on when the system senses that it cannot activate the airbag; this means that there is some sort of a problem with the airbag system in your vehicle.

Can a blown fuse cause the airbag light to come on?

There are many possible fuses that could be behind this, but fuse #13 is a likely culprit. If your airbag light is on and your rear windshield wiper doesn’t work, then it’s a pretty good indication that you need to change fuse #13 and possibly others. Blown fuses can definitely cause the airbag light to come on.

How much does it cost to reset airbag?

At the very least, the ECU or airbag module will need to be reset costing about $50 to $150. If the airbag control module needs replacing, expect to pay anywhere from $400 to $1,200 for a new one.

Can you drive with airbag light on?

The bottom line is that, when your airbag light comes on, it’s vital that you don’t drive any further and have your car checked by a mechanic as soon as possible. Until the problem is diagnosed and fixed, your airbags will not deploy.

How much does it cost to reset airbag light?

Number 1 — Reset Airbag Light

This process can take several hours of time and usually costs a few hundred dollars, although depending upon the type of car it may be up to about $600.

HOW TO RESET AIRBAG LIGHT WITHOUT SPECIAL TOOLS ON CHEVY, CHEVROLET, GMC, BUICK, CADILLAC

How to Reset Airbag Light (10 Simple Steps) – Off-Roading Pro

Article author: offroadingpro.com
Reviews from users: 20141 Ratings
Top rated: 5.0
Lowest rated: 1
Summary of article content: Articles about How to Reset Airbag Light (10 Simple Steps) – Off-Roading Pro Updating …
Most searched keywords: Whether you are looking for How to Reset Airbag Light (10 Simple Steps) – Off-Roading Pro Updating Some ways to reset an airbag light include inspecting seat belt components, changing defective clock springs, and replacing faulty sensors.
Table of Contents:

How to Reset Airbag Light (10 Steps)

How to Reset Airbag Light on Chevy

Conclusion – How to Reset Airbag Light

How to Reset Airbag Light (10 Simple Steps)

Disclosure: We may get commissions for purchases made through links in this post.

The airbag light is part of the Supplement Restraint System (SRS) in vehicles, linking the airbag system to the seat belt system (and vice-versa). When you start your car, the airbag light turns on within 5-7 seconds before turning off, indicating a successful and completed internal system check. The problem begins when the airbag light never turns on or stays on and blinks. At this point, resetting the airbag light becomes crucial.

Some ways to reset an airbag light include inspecting seat belt components, changing defective clock springs, and replacing faulty sensors. You could also get new bulbs or fully charge your battery. While most fixes are DIY, others may require a mechanic.

Here are 10 steps on how to reset your airbag light:

Turn your ignition on and off. Restart your vehicle and do a test drive. Examine the passenger airbag switch. Inspect whether seat belts are fastened or working correctly. Verify that the passenger seat sensor is not applied. Use a scanner with an SRS or airbag light reset option. Address faulty airbag sensors. Fix or replace a non-working clock spring. Make sure the airbag is not defective. Seek assistance from a professional.

While the above list is non-exhaustive, it sums up proven-and-tested ways of resolving the issue. You may find some of them inapplicable, as compatibility would always depend on your vehicle’s year, make, and model. In performing any of these fixes, it would be best to have your service manual with you. Additionally, always adhere to manufacturer instructions. Without further ado, let us delve into resetting your airbag light.

How to Reset Airbag Light (10 Steps)

Ideally, the airbag light (a.k.a. SRS light) illuminates on a vehicle’s instrument panel (view on Amazon) only after an accident, when the airbag has been deployed and filled with either argon or nitrogen. However, other circumstances – like a component or sensor malfunction – cause the airbag light to stay on. Having said this, car owners would benefit from a handheld airbag light reset tool and by performing the steps below.

1. Turn Your Ignition on and Off.

This procedure is the same as resetting the airbag light on a Toyota Camry and should be the first thing to do when you encounter the same issue. It entails four simple steps that are easy to follow and requires timing the airbag light.

First, turn the ignition switch on. Next, wait for the airbag light to turn on – it normally stays lit for seven seconds before shutting itself off. Then, immediately turn off the ignition switch, and wait three seconds. Repeat the initial steps once or twice before starting the engine. If everything is done correctly, your car’s airbag light should come on for seven seconds before shutting off for good.

2. Restart Your Vehicle and Do a Test Drive.

Like your mobile phone, your car may need a power cycle. However, this will not work for all vehicles. But for those that seem to glitch now and then, it just might. You would know to take this step if the airbag light does not stay on too long. Restart your ignition, then go for a short drive. If the airbag light goes away permanently afterward, the problem is most likely solved. If not, proceed to perform the other items in this list.

(TIP: Before restarting your vehicle, examine the wiring system underneath the driver and passenger seats. Look for any loose wires or rust formation in the connector plug. If none, spray the connector plugs with an electronic cleaner.)

3. Examine the Passenger Airbag Switch.

The passenger seat airbag on/off button (only available in some cars) should be one of the first things to check when attempting to shut off the airbag light. It is possible that someone turned it off erroneously, causing the airbag light to stay on. This button is normally on the dashboard on the passenger side but is sometimes visible once you open the glove box or passenger door.

4. Inspect Whether Seat Belts Are Fastened or Working Correctly.

Since the SRS deals with driver/passenger security, sensing loose or poorly strapped seatbelts can trigger the airbag light to come on. Even non-use of seat belts can automatically disable the airbag. That said, ensure proper function of seatbelts and seat belt sensors is in your rule-out list. Mechanics would advise the same to those doing a Jeep Wrangler airbag light reset.

You may find it incredulous, but simple things like spare change can render seat belt sensors defective. Often, change is placed close to the seat belt fasteners, and a small bump or pothole can get a small coin into the fastener and in-between the sensor and the buckle. When this happens, the sensor may not recognize when a seat belt fastens, activating the airbag light in the process.

Before replacing your sensors, check inside the buckle and see if anything is stuck inside. Usually, taking out any obstructions inside the seat belt fastener is not as expensive as most vehicle owners think. However, the reverse is true if your seat belt components cannot be replaced individually and the sensors are embedded in the seat belt.

5. Verify That the Passenger Seat Sensor Is Not Applied.

Select vehicles have an overly sensitive passenger weight sensor. The trouble with these specific cars is that the sensors easily trip just by placing a large box or container on the passenger seat. As a result, the airbag light turns on.

There are two options to address this – either remove the object from the passenger seat or hook up the seatbelt. If the latter solves the problem, it would confirm the sensor was applied, causing the airbag light to illuminate. If the airbag light turns off after fastening the seat belt, but nothing is in the seat, it would mean a faulty passenger seat sensor. You can then determine if you want to replace the sensor or keep the seat belt buckled up whenever you drive.

6. Use a Scanner With an SRS or Airbag Light Reset Option.

If you are mechanically inclined, you can purchase a scanner with SRS capability to perform an airbag light reset. Just know that not all OBD-II devices are automatically airbag light reset tools. Purchasing an OBD-II scanner with your needed feature warrants a bit of research. I would recommend the Foxwell NT634 OBD-II Scanner (view on Amazon) — this tool displays error codes that help you figure out how to fix the issue or when it is best to take your vehicle to a mechanic.

7. Address Faulty Airbag Sensors.

Sensors play a big part in a car’s function, especially with more recent vehicle makes and models. For one, sensors ensure airbags deploy in the event of a fender bender. The SRS particularly works with the aid of multiple sensors installed in different vehicle parts/components. If any one of these sensors corrode, break, or stop working, you are certain to see the airbag light on.

In some cases, airbag sensors act up – activating all of a sudden and for no apparent reason. They can also fail and throw the SRS light on if the car has suffered water damage. There are situations, too, where the airbag system control unit may have just gone bad. When any of these occur, replacing the bad sensors, control unit, or water-damaged components may solve the problem.

8. Fix or Replace a Non-Working Clock Spring.

Otherwise known as a spiral cable, coil assembly, contact reel, or cable reel assembly, the clock spring is a major component that, when broken or damaged, can cause the airbag light to turn on. It is not only one of the most common reasons behind a flashing airbag light but also among the most expensive to fix (at least $400). You can save up on costs if you change the clock spring yourself – provided you take extreme caution and adhere to manufacturer instructions.

If you suspect it is the cause of your airbag light activating, you will need to access the inside of the steering wheel (view on Amazon) to fix it. This should be no cause for worry as the entire process is simple and takes only 10 steps and less than 20 minutes to complete:

How to Fix a Clock Spring

Remove the negative battery cable from the terminal; Wait for the capacitors to discharge for at least 10-15 minutes. (Note that removing the car battery terminals by itself will not reset the airbag light). With the wheels straight, hold the wheel’s center section (the location of the airbag) in place and locate the screws. Then, unscrew them. Remove the airbag by pulling it towards you and remove the connectors (you may use a pick to slide the yellow clips out when doing this). Turning the steering wheel left to right also exposes the screws that hold the steering column trim in place. With the steering lock engaged, use two pieces of painter’s tape to mark the spot between the steering wheel and steering column trim. This reference point will come in handy when returning the steering wheel to its original position later on. Loosen the steering wheel nut with a breaker bar without removing it completely. Remove the nut and wheel once the wheel is loose, exposing the clock spring. To remove the clock spring, disconnect the harnesses at the bottom or back. Replace the old one with a new clock spring. Break the tab off by bending it until it snaps. Refer to your tape marks to line up the steering wheel properly when reinstalling. Tighten the steering column nut to the specified torque with a torque wrench (or your hands and a breaker bar); Install the harnesses along with the airbag. Reinstall the lower steering column (view on Amazon) trim piece and reconnect the negative battery terminal. You should no longer have a flashing airbag light when done with this final step.

9. Make Sure the Airbag Is Not Defective.

Although rare, faulty airbags are not unheard of. It could be the reason behind having difficulty in resetting the airbag light. If it does turn out to be the culprit, know that this is not something you can tackle on your own. Resolving this problem entails professional help – and a few hundred dollars.

Depending on your vehicle’s make and model and how intricate the SRS is, replacing airbags typically fall between $200 and $1,000 (without labor fees). Labor costs vary depending on which airbag is faulty. Driver-side airbags have proven easier to replace compared to side or passenger airbags. Hence fees are more expensive when working on the latter. Either can be expensive but not something you would want to procrastinate on.

10. Seek Assistance From a Professional.

Take your car to a mechanic if all else fails. This route will be more expensive, but the mechanic should correctly identify the cause of your flashing airbag light and permanently solve the problem. Unlike tech-savvy drivers, new vehicle owners would primarily consider this as their first course of action.

How to Reset Airbag Light on Chevy

Firstly, plug your OBD-II/SRS code scanner into the vehicle. Like most cars sold in the U.S. in the last two decades, Chevrolets have a designated OBD-II port. The said port is trapezoidal and typically found under the dashboard (driver’s side). Note that it is not available for pre-1996 Chevy models.

Next, turn on the ignition but do not start the engine. If you see a start/stop button, press it (make sure not to press the brake pedal as you do this). Then allow the airbag scanner to power on – this should happen simultaneously with the ignition turning on. Once the airbag scanner is fully powered, select “Chevrolet” from the menu.

Follow the prompts on the airbag scanner until you get to select “Airbag System.” Afterward, scroll down to scan your Chevy for airbag fault codes. Address the fault codes that show the status “Present” or “Current.” Stored or past codes are okay to clear.

After clearing airbag light-related fault codes, turn the ignition off then back on to determine if the airbag light successfully reset. If not, go back to the “Airbag/SRS control unit” option, and erase fault codes. All these steps should suffice in resetting the airbag light and also apply to Chevy Spark, Sonic, Bolt, Volt, Cruze, Malibu, Impala, and Camaro – to name a few.

Conclusion – How to Reset Airbag Light

To recap, here are 10 simple steps on how to reset the airbag light of your vehicle:

Turn your ignition on and off. Restart your vehicle and do a test drive. Examine the passenger airbag switch. Inspect whether seat belts are fastened or working correctly. Verify that the passenger seat sensor is not applied. Use a scanner with an SRS or airbag light reset option. Address faulty airbag sensors. Fix or replace a non-working clock spring. Make sure the airbag is not defective. Seek assistance from a professional.

If you suspect your car is affected by a recall, make sure you watch for DMV mails. You can also check open recalls on your vehicle by going to the National Highway and Traffic Safety Administration (NHTSA) website and entering your car’s VIN. I strongly suggest doing this if you own a secondhand four-wheeler. At best, you may not have to spend a dime on repairs.

Due to accompanying costs, it can feel tempting to put off resolving an airbag light reset for later. However, it would be unwise to do so. One of two things could happen – either the airbag deploys when it doesn’t need to or doesn’t deploy when you need it most. Either could result in catastrophic consequences and isn’t worth the risk.

How to Reset Airbag Light? (5 Steps) With or Without Scanner

The airbag can definitely save your life one day if the accident occurs. If you repaired the airbag system, it is now time to reset the airbag light. Here is how you can do it

Did your airbag light pop up on your dashboard, and you now want to know how to reset it?

The engine and airbag lights are some of the dashboard lights you need to pay extra attention to if they light up, especially the airbag light due to its safety importance.

Airbags are designed so they inflate whenever there is a collision, and when the light is on, this will not happen.

How do airbags work?

So before we look at how to reset the airbag light, you should know how the whole function works.

Airbags are lifesavers when you are speeding and hit another car head-on or hit a stationary object. If you do not have an airbag, you could hit your head hard on the steering wheel or dashboard. When you hit something at high speed, your car will decelerate, and this will activate an accelerometer that triggers the airbag circuit.

The airbag circuit has a heating element activated through an electric current. This heating element promotes an explosion inside the airbag that rapidly generates a harmless gas. Most airbags use sodium azide as the explosive element, and the gas produced can either be argon or nitrogen. This gas floods the airbag and causes it to expand; hence, protecting the driver from injuries by occupying the steering wheel and the side. The airbag acts as a cushion.

How to reset the airbag light with a scanner

Now that we know how airbags operate, it is time to learn how to reset the airbag light.

All work done to the airbag system should be made by professionals if you are not 100% sure of what you are doing! Follow these steps to reset the airbag light: Total Time: 1 hour Step 1: Check the passenger airbag switch Some cars have a “passenger seat Airbag on/off button.” This is the first thing you should check when you want to remove the airbag light. Maybe someone before you turned it to Off by mistake, which will make the airbag light stay on in most cars.

This button is usually on the dashboard on the passenger side, and you may see it if you open the passenger door or the glove box. Step 2: Read the trouble codes with an OBD2 Scanner Working with your airbag system is crucial, and therefore, always read the trouble codes with an OBD2 scanner to get an idea of where to start your troubleshooting. Do never clear the trouble codes before you fix the problem caused by the airbag light. Read the codes and get information about what can cause the problem and therefore continue the diagnosis. Step 3: Repair the fault You should never just reset the airbag light without repairing the problem. This can deploy the airbags or non-functioning if an accident occurs. Let a professional replace the airbag’s parts if you are not sure of how to do it. Remember always to remove the battery connection when working with airbags. The airbag light will often go away by itself after repairing the problem, but not in all car models. Step 4: Clear the trouble codes After you have installed the new parts and are 100% sure that the parts are installed correctly, it’s time to reset the engine light. To do this – you need to use an OBD2 scanner, and it’s not possible in another way. Reset the airbag light and make sure that it disappeared from the dashboard. If it is still there – reread the codes and check for any trouble codes. Step 5: Restart your car & test-drive. If the airbag light seems to have gone away from your dashboard – restart your ignition and go for a test drive. If the airbag light is gone after a test drive, there is a big chance that the problem is solved. If the problem comes back, reread the codes and continue the procedure.

How to reset airbag light without a Scanner

It is impossible in most car models to reset the airbag light without a scanner. This is for safety cautions because you should always repair the fault after the airbag light occurred. Luckily, in many car models, the airbag light will also go away by itself if you have repaired the problem.

In some older cars, though, it is possible to reset the airbag light without a scanner by removing the car battery terminals.

Check the wiring system underneath the driver or passenger seat for any loose wires or corrosion in the connector plug. Spray the connector plugs with an electronic cleaner and restart your car.

If you can not find any problems there, you should really get an OBD2 scanner or let a workshop read the codes; otherwise, you will just guess the problem out of the dark.

How do i reset airbag light on chevy silverado?

star Top Answer

accountCircle Robert H. December 28, 2020

To reset the airbag light in a Chevy Silverado You need to have the truck diagnosed using a computerized scan tool. There are numerous reasons that would cause the light to illuminate. The scan tool will plug into the OBD-II Port and will let You know where the issues are. There are several sensors on the truck from the front and rear bumpers, seatbelts, and doors. It could be that one of the sensors has failed, an electrical connector is loose or one of the pins are damaged. It can cost between $170 to $190 have a defective sensor replaced, this includes labor costs. Before takeng the Silverado to the shop, check the supplemental restraint system fuses and replace them as needed.

So you have finished reading the how do you reset the airbag light on a chevy topic article, if you find this article useful, please share it. Thank you very much. See more: how do you reset the airbag light on a chevy avalanche, how to reset airbag light on chevy tahoe, how to reset airbag light on chevy impala, how to reset airbag light on chevy equinox, how to reset airbag light on chevy cobalt, how to reset airbag light on chevy traverse, how do you reset the airbag light on a gmc sierra, how to reset service airbag light on gmc terrain

Top 23 How Do You Reset The Airbag Light On A Chevy Best 131 Answer

Can you reset airbag light without tool?

What causes the airbag warning light to come on?

Can a blown fuse cause the airbag light to come on?

How much does it cost to reset airbag?

Can you drive with airbag light on?

How much does it cost to reset airbag light?

How to Reset Airbag Light (10 Simple Steps) – Off-Roading Pro

How To Reset Airbag Light (5 Steps) With Or Without Scanner

ERROR: The request could not be satisfied

chevrolet – How to Reset AirBag codes without expensive scanner? – Motor Vehicle Maintenance & Repair Stack Exchange

Chevy Airbag Light Stays On | Troubleshooting Guide

How To Reset Airbag Light On Chevy? [8 Easy Steps]

How to Reset Airbag Light (10 Simple Steps)

How to Reset Airbag Light? (5 Steps) With or Without Scanner

How do i reset airbag light on chevy silverado?

Leave a Comment Cancel reply