You are looking for information, articles, knowledge about the topic nail salons open on sunday near me how to charge airsoft lipo battery on Google, you do not find the information you need! Here are the best content compiled and compiled by the Chewathai27.com team, along with other related topics such as: how to charge airsoft lipo battery how to charge a lipo battery, how to charge airsoft battery without charger, charging a 4s lipo battery, airsoft battery charger, titan digital lithium battery charger error codes, how to store airsoft battery, how to charge titan battery, airsoft lipo battery guide
Contents
Do Airsoft LiPo batteries come charged?
When you get a new lipo battery it will already come partially charged. This partial charge is called the Storage Voltage. Storage voltage is where each cell is charged to approximately 3.8 volts. (Don’t worry if you are unfamiliar with battery cells, we will get more into that later).
How long does it take to charge a Lipo battery Airsoft?
It’ll take ten hours to charge this completely dead/new battery to its full capacity. Simply just divide the mAh from the charger to the mAh of the battery! It can be left and claimed later but do keep an eye on it from time to time.
Do LiPo batteries need a special charger?
It’s important to use a LiPo compatible charger for LiPos. As I said in the Introduction, LiPo batteries require specialized care. They charge using a system called CC/CV charging. It stands for Constant Current / Constant Voltage.
Can you charge a LiPo battery with a normal charger?
You can use a lead-acid charger to charge lithium batteries as long as you can set the maximum voltage of the charger and as long as the charger does not have an automatic equalisation mode enabled.
How long does an 11.1 LiPo take to charge?
If you have a LiPo and the orange “CHARGER EK2-0851” it should take about 2½ – 3 hours to charge. The battery should never get warm while charging.
Can you charge Li ion batteries with a LiPo charger?
Dedicated 18650 chargers terminate at 4.2v or sometimes slightly below to prolong cell life. So, if we’re talking about ‘lithium ion’ as in 3.7V nominal, 4.2V max, then a lipo charger will be fine so long as you watch the charge rate on the li-ion cells.
Can airsoft batteries explode?
They come in different sizes and can fit almost any tight space. But the disadvantage of LiPo batteries, they have the tendency to combust or explode when mishandled, stored, charge or discharged improperly. Always strictly follow instructions from the user manual.
How do you keep LiPo batteries healthy?
- Never store loose batteries together. …
- Never store batteries in extreme temperatures or direct sunlight. …
- Always disconnect Batteries when not in use and store batteries in a non-conductive and fireproof container.
- Never alter, puncture or impact Batteries or related components.
How long should I charge my 9.6 airsoft battery?
Your battery pack consists of new parts and materials; therefore, you should charge the battery pack for 5 1/2 hours the first two times you charge the battery. Subsequent charges will require only 4 hours.
How long does a 9.6 V Airsoft battery last?
Lasts for a few hours, around 3-3.5 on a full charge and playing hard.
How long do airsoft batteries last?
Shots Per Battery
If you are using a 1,400 mAH battery, for example, you can expect to fire about 1,400 rounds before your battery goes dead. That may sound like quite a lot, but keep in mind that many airsoft battles often last several hours.
Do you have to balance charge Lipos every time?
So when charging LiPo batteries, usually you only have to adjust to the charge current. It’s recommended to always use balance charging. Balancing chargers ensure that all the cells are charged evenly and there are no differences in voltages between them.
HOW TO CHARGE YOUR LIPO BATTERIES LIKE A PRO | TIPS & TRICKS | CHARGING & MAINTENANCE GUIDE – YouTube
- Article author: www.youtube.com
- Reviews from users: 14704
Ratings - Top rated: 4.9
- Lowest rated: 1
- Summary of article content: Articles about HOW TO CHARGE YOUR LIPO BATTERIES LIKE A PRO | TIPS & TRICKS | CHARGING & MAINTENANCE GUIDE – YouTube Updating …
- Most searched keywords: Whether you are looking for HOW TO CHARGE YOUR LIPO BATTERIES LIKE A PRO | TIPS & TRICKS | CHARGING & MAINTENANCE GUIDE – YouTube Updating G’Day Fam,Today we are going to show you how to charge and maintain your precious LiPo Batteries.If you want to understand how to care and get the best out o…RC, Radio, Control, Horizon, Hobby, r/c, radio, control, remote, Radio Control (Invention), Remote Control (Invention), Pro Boat, Proboat, Models, Boat, Power Boat Racer, Power, 17, 17-inch, Self-Righting, Deep-V, Hull, Brushless, SMART, Technology, Spektrum, Spectrum, RTR, Ready-to-Run, Ready, Run, Lucas Oil, Miss GEICO, Lake, Pond, Pool, River, Stream, Water, Ocean, Beginner, Charger, LiPo, Battery, Pack, Lithium, 11.1, 3s, AC, Dynamite, ESC, 2.4GHz, 2.4, GHz, Transmitter, traxxas maxx, traxxas, gens ace, gens ace lipo
- Table of Contents:
How to Charge Titan Airsoft Lithium Ion – YouTube
- Article author: www.youtube.com
- Reviews from users: 5398 Ratings
- Top rated: 4.5
- Lowest rated: 1
- Summary of article content: Articles about How to Charge Titan Airsoft Lithium Ion – YouTube Updating …
- Most searched keywords: Whether you are looking for How to Charge Titan Airsoft Lithium Ion – YouTube Updating video, chia sẻ, điện thoại có máy ảnh, điện thoại quay video, miễn phí, tải lên
- Table of Contents:
Beginners Guide to LiPo Batteries — FPV Freedom Coalition
- Article author: fpvfc.org
- Reviews from users: 36074 Ratings
- Top rated: 4.0
- Lowest rated: 1
- Summary of article content: Articles about Beginners Guide to LiPo Batteries — FPV Freedom Coalition Updating …
- Most searched keywords: Whether you are looking for Beginners Guide to LiPo Batteries — FPV Freedom Coalition Updating
- Table of Contents:
How Long to Charge An Airsoft Battery | What You Need to Know | AIRSOFT BLOG | REDWOLF AIRSOFT
- Article author: www.redwolfairsoft.com
- Reviews from users: 20252 Ratings
- Top rated: 4.1
- Lowest rated: 1
- Summary of article content: Articles about How Long to Charge An Airsoft Battery | What You Need to Know | AIRSOFT BLOG | REDWOLF AIRSOFT Updating …
- Most searched keywords: Whether you are looking for How Long to Charge An Airsoft Battery | What You Need to Know | AIRSOFT BLOG | REDWOLF AIRSOFT Updating Redwolf Airsoft
- Table of Contents:
What is an airsoft battery
What is the purpose of an airsoft battery
Different kinds of airsoft batteries
But Wait There’s More!
How long to charge the airsoft battery
How Do I Know The Battery Is Full
Recommended
What is an Airsoft Hop-Up and Why do You Need It
How Long to Charge An Airsoft Battery | What You Need to Know | AIRSOFT BLOG | REDWOLF AIRSOFT
- Article author: www.redwolfairsoft.com
- Reviews from users: 3375 Ratings
- Top rated: 4.6
- Lowest rated: 1
- Summary of article content: Articles about How Long to Charge An Airsoft Battery | What You Need to Know | AIRSOFT BLOG | REDWOLF AIRSOFT The best and safest way to know when the airsoft battery is fully is by using a smart charger. But keep in mind that do not try to charge 2 … …
- Most searched keywords: Whether you are looking for How Long to Charge An Airsoft Battery | What You Need to Know | AIRSOFT BLOG | REDWOLF AIRSOFT The best and safest way to know when the airsoft battery is fully is by using a smart charger. But keep in mind that do not try to charge 2 … Redwolf Airsoft
- Table of Contents:
What is an airsoft battery
What is the purpose of an airsoft battery
Different kinds of airsoft batteries
But Wait There’s More!
How long to charge the airsoft battery
How Do I Know The Battery Is Full
Recommended
What is an Airsoft Hop-Up and Why do You Need It
Airsoft LiPo Guide for Noobs : airsoft
- Article author: www.reddit.com
- Reviews from users: 32676 Ratings
- Top rated: 3.8
- Lowest rated: 1
- Summary of article content: Articles about Airsoft LiPo Guide for Noobs : airsoft Answer: To prepare your LiPo for medium- to long-term storage you should charge it (or discharge it, as necessary) to about 3.8V per cell (0.1V … …
- Most searched keywords: Whether you are looking for Airsoft LiPo Guide for Noobs : airsoft Answer: To prepare your LiPo for medium- to long-term storage you should charge it (or discharge it, as necessary) to about 3.8V per cell (0.1V … 81 votes, 60 comments. Airsoft LiPo Guide I am not a total noob, but after searching through this subreddit I didn’t find any …
- Table of Contents:
How To Charge And Store Airsoft Battery (With Safety Tips) – Airsoft Garrison
- Article author: airsoftgarrison.com
- Reviews from users: 45344 Ratings
- Top rated: 4.9
- Lowest rated: 1
- Summary of article content: Articles about How To Charge And Store Airsoft Battery (With Safety Tips) – Airsoft Garrison To fully charge an airsoft battery you will need to dive the battery’s mAh (Milliam hours) with the charger’s mA (Miliams per hour) and charge it for that … …
- Most searched keywords: Whether you are looking for How To Charge And Store Airsoft Battery (With Safety Tips) – Airsoft Garrison To fully charge an airsoft battery you will need to dive the battery’s mAh (Milliam hours) with the charger’s mA (Miliams per hour) and charge it for that … Batteries are extremely important in airsoft and sometimes they can make or break an AEG. As a matter of fact, batteries are amongst the first…
- Table of Contents:
How long should you charge the battery
How to know when the battery is charged
What happens if you overcharge the battery
Tips for proper charging of a battery
Should I charge my airsoft battery overnight
Do airsoft batteries lose charge over time
Do airsoft batteries come charged
How to store airsoft batteries
Can you leave a battery in an airsoft gun
Types of chargers you can use
About Us
LEGAL INFORMATION
LiPo Battery Charging, Storage, and Handling
- Article author: www.airsoftmaster.com
- Reviews from users: 48180 Ratings
- Top rated: 4.2
- Lowest rated: 1
- Summary of article content: Articles about LiPo Battery Charging, Storage, and Handling LiPo Battery Charging · Always use a charger made for LiPo batteries. · LiPo Batteries should be charged no more than 4.2 volts per cell. · LiPo Batteries should … …
- Most searched keywords: Whether you are looking for LiPo Battery Charging, Storage, and Handling LiPo Battery Charging · Always use a charger made for LiPo batteries. · LiPo Batteries should be charged no more than 4.2 volts per cell. · LiPo Batteries should … Lipo Battery, lithium polymerHow to properly charge, store, and handle LiPo or Lithium Polymer Batteries. More airsoft tips and tricks by AirsoftMaster.com
- Table of Contents:
LiPo Battery Charging
LiPo Battery Storage & Handling
See more articles in the same category here: Chewathai27.com/toplist.
Beginners Guide to LiPo Batteries — FPV Freedom Coalition
The usable voltage range for a standard lipo battery cell is 3.2v to 4.2v. Any lower than 3.2v and the battery may be permanently damaged. Any higher than 4.2v and you significantly increase the risk of a battery bursting into flames. Normally you will start with a battery cell that is at storage charge or 3.8v, place it on the charger, let the charger charge the battery to 4.2v, then go fly until the battery cell voltage drops to somewhere in the 3.5v to 3.7v range depending on how nice you want to be to your batteries and your comfort level. You might ask, why not fly until they are all the way down to 3.2v? Well, you can, but that puts additional strain on the batteries, shortens their life a little bit, and typically when you fly and give the drone a burst of throttle, the battery will sag and the voltage will drop as it tries to provide all the power it can. If this sag causes the battery cell to go below 3.2v, it will cause more damage. Also many drone batteries are created from multiple cells and you don’t always know the exact voltage of each cell. If you have a battery created from 6 cells, they won’t all discharge at exactly the same rate and you could end up with one cell at 3.0v and others at 3.4v. In that case you risk damaging a cell or the entire battery. So that is why the recommendation is to land when your batteries are at 3.5v per cell or greater. You may also notice that after you land and give your batteries a few moments to recover from their hard work, the voltage will recover slightly and your 3.5v battery cells may stabilize closer to 3.6v or 3.7v per cell. Some people will even stop flying at just the right time such that their batteries are at 3.8v per cell so they won’t have to storage charge them when they are done. You get less flight time this way but it might be worth the trade off to you.
Battery Cells
Drone batteries come in all sorts of shapes, sizes, cell counts, connector types, and more. Everything from a very small single cell battery for a “Tiny Whoop” to a large 6 cell battery often used in drones with 5″ propellers. ( Yes, they do come larger than 6 cell varieties, but if you need one of those this guide is probably not for you. ) When you add multiple cells together to create a bigger more powerful battery, the voltage of the entire battery is multiplied by the number of cells. For example a 4s battery, which contains 4 lipo cells in series, would have a maximum charge of 4.2v x 4, or 16.8v. A 6s battery would have a maximum charged voltage of 25.2v. And the more voltage you have, the faster an electric motor will spin. Which is also why it is important to pair the right rpm motor with the right battery voltage. But we will leave that for another guide. The important part here is to understand the relationship between voltage and cell count. I would also recommend having your OSD display the average cell voltage in your FPV goggles. That way it won’t matter if you are flying with a 4s or 6s battery, either way it will show you the average cell voltage and you will get used to using that value to decide when to land.
You may also see a battery listed as 4s2p, or 2s2p. That is just letting the buyer know that there are some cells in series and some cells in parallel to create the voltage and capacity necessary for the overall battery. So in the case of a 4s2p it lets you know that there are 4 cells wired in series each made up of 2 cells wired in parallel for extra capacity without increasing voltage.
Any lipo battery made from more than one individual cell has the potential to have the cells become out of balance. Ideally you want all the cells in a single battery to be at the same voltage at all times. To help you achieve this, your lipo charger has a charging option called “balance charging”. Some chargers will also split the charging up into “fast charging” and “balance charging” phases where they will first quickly charge up the cells to something close to fully charged, and then slowly top them off while checking the voltage of each individual cell to make sure they are all equally charged when finished. For maximum health, you should always balance charge your batteries. This is also why your 2 cell or greater LiPo battery has a second plug on it. This second plug is called the balance plug and is used by your charger to individually monitor and balance charge each cell.
How Long to Charge An Airsoft Battery
What is an airsoft battery?
Finally, your new airsoft gun arrives on your front porch, and you’re all excited to try it, but likely it doesn’t take standard AA batteries. Most Electric Airsoft guns require high-power rechargeable batteries, and you also need a battery charger to juice it up. The most popular Airsoft batteries are Lithium Polymer (LiPo) and Lithium-Ion (Li-Ion). But do you know how long to charge an Airsoft battery? Not all battery chargers are intelligent and know when to stop charging. Will I fry the battery, or worse yet, burn down the house? Read on as we give you a quick crash course on airsoft batteries and how to charge them.
Click on Photo for More Information
Most automatic electric guns (AEG) these days do not come with a battery or charger, so it’s a good idea to do some research before swiping that card. Depending on which AEG you buy, the connector type is different from brand to brand too. There are several different kinds of connector plug types, so keep in mind which one your gun uses when purchasing a battery. To save from buying all kinds of different batteries, you should consider standardizing on one plug type across all your AEGs so that your batteries are cross-compatible on all your Airsoft guns.
Mini Tamiya Connector.
Most standard AEGs come with a standard plastic semi-translucent connector plug known as mini-Tamiya. This plug type is very popular in R/C cars and planes. The benefit of using this type of plug is that they have a locking mechanism that prevents accidental disconnection. This connector physically isolates the positive and negative wires, which means it’s safer to use in damp environments. Safe for use in relatively low-current applications (up to about 15 A), the design provides safety and is fool-proof. If you like crawling around in the dirt or going prone, then the mud or water shouldn’t be able to penetrate this connector.
This is NOT a Mini Tamiya Connector! It’s a Tamiya connector.
The issue with these connectors is that the area of contact is small. Thus it can cause issues with the current flow, slightly decreasing your trigger response! Since they are made from softer nylon-based plastic, they can break quite easily and are not as durable as deans. Tamiya plugs are also bulky compared to deans plugs, which we will talk more about below. But Tamiya plugs are still popular in Japan, and hence Japanese made Airsoft guns will usually come with them.
Deans connector.
Moving on to the other type of connector is Deans. The connectors are based on big metal pieces shaped in the letter ‘T’, which lock into each other when connected. This provides a huge area of contact, which results in a higher flow of electrical current to the motor. Say hello to a higher fire rate and consistent electricity flow! They last longer than mini Tamiya as it’s constructed out of better materials. Slowly being phased out, Mini Tamiya is replaced by Deans.
In the airsoft community, one of the most common questions regarding airsoft batteries is “How long do I charge my battery for?”. Every battery is different, so there are no set rules on how long to charge it for.
We at Redwolf Airsoft have all kinds of batteries available, not to confuse you, we will stick to the ones we offer. If you own an RC model then you may notice they use very similar batteries. In fact, they are the same batteries!
What is the purpose of an airsoft battery?
Think of your AEG as an electronic device, mobile phone, shaver, wireless headsets, etc. They are all powered by one thing, a battery. This brings life into the products we use on a daily basis which applies to an AEG too. Without it, your AEG is as good as a mantlepiece in your home.
Known as mAh, or milliamp Hour, this is the number of energy batteries can store. Commonly used to measure the energy capacity of a battery, it’s a unit that measures (electric) power over time. In general, the more mAh there is, the longer the battery life which means more pew.
Let there be life!
So does this mean you’d want to find the one with the most capacity? Yes, but you have to make sure it can fit into your AEG! In most cases the more mAh, the bigger size of the battery. A good rule of thumb is to stick to something around 1500 mAh as they will most likely last a full day and fit most regular stocks. Just keep in mind if you’re trigger happy and enjoy beams of BBs at full auto then it may not last an entire day. We recommend a backup battery just in case; there’s nothing worse than running out of power during the final moments of a game and without a spare in sight!
Different kinds of airsoft batteries?
Nickel-metal hydride (NiMh), lithium-ion polymer (LiPo), nickel-cadmium (NiCad), and alkaline are the four types of batteries used in an AEG. Barely anyone uses NiCad or alkaline anymore as they are not as efficient or cost-effective.
Where do I start?
NiMH batteries are like your everyday rechargeable AA batteries, common, very safe, withstand cold weather, and hold charge well which can last for one to two years even when charged often. In recent years the trend in this type is transitioning away to current generation batteries which are similar to tablets or mobile phones (LiPo). NiMH batteries will self-discharge when left alone, especially in a warm environment. To squeeze more life out, it shouldn’t be fully depleted every game, though once in a while discharged fully.
Using a fast charger will likely heat it up before fully charged, unfortunately, they cant be quickly charged. A slow charge is much safer and healthier for these types.
Click on Photo for More Information
They also discharge much faster than any other when left standing, in high discharge applications it can’t reach their full potential. Charging them with more than 1.5 amps or quick discharges will damage the battery.
You may have heard the term “Memory Effect”, older generation batteries had problems as they memorized when it was discharged to a certain point repeatedly, causing a reduction in capacity. Fear not as current NiMH batteries on the market will not do that! It will come back to its full capacity after each and every charge. When overcharged it can be brought back to life by safely discharging, that’s why it’s preferred by many airsofters for its sheer reliability.
Pros Affordable
Commonly used in many AEG airsoft guns
Withstand cold weather
Longer lifespan Cons Slow charge
Discharge at a higher rate than other types
Slowly phasing out of the market
Lower energy capacity
Click on Photo for More Information
Holding way more charge and lasting longer compared to NiMH batteries, LiPo batteries are the most advanced battery on the market. Used practically everywhere including your mobile phone or tablet these are the current-gen of batteries. They come in two voltages, 7.2v or 11.2v perfect for an upgraded AEG that has a high rate of fire. If overcharged they can explode and cause chemical burns, fires, or even death in some cases. With an average price tag of $63 or more for just the battery and another $54 for the charger, it can be expensive. A lot of fraudulent sellers out there label their battery ratings incorrectly making them even more dangerous. So rest assured as we only sell quality, safe batteries, and chargers.
Unlike the NiMH battery type, there are no methods for optimal and healthy life of the LiPo battery, just make sure to never let it fully discharge. So as soon as your AEG starts to slow down and the gears turn slower with each shot, return to the safe zone and pop some new ones in.
Pros Unaffected by hot/cold
Commonly used in many AEG airsoft guns
Supports fast charge
Lighter than NiMH Cons Expensive
Dangerous if overcharged
Fragile
Require specific charger
Click on Photo for More Information
You may have heard of nickel-cadmium (NiCad) batteries, they are similar to the NiMh batteries but bulkier, heavier, and cant handle extreme temperatures well. What’s impressive about these is that they are able to quick charge and discharge with almost no damage done to the cells, perfect for guns that draw large energy and high rates of fire! Overcharging it can cause battery cells to split, leak, and even cause a fire so they should never be left alone even with a smart charger.
Pros Undamaged cells via charging/discharge
Lowest charging time out of all other types Cons Bulky and heavy
Prone to temperature changes hot/cold
Outdated
Only recharge when empty
Alkaline Batteries
Variety Of Alkaline Batteries.
The OG of batteries, alkaline. You won’t see this in airsoft these days because they cannot take the energy consumption from an AEG nor provide a high rate of fire. If stored in a room temperature (70F), or colder environment they can last years before losing even a sliver of a charge! Being very common this makes them way more affordable compared to NiMh or LiPo. Due to the chemical property, they can’t be recharged numerous times and can’t take the high voltage pull that AEG requires. Your pew time would be cut short as they barely have the capacity!
Pros Common
Hold charge for a long time Cons Limited capacity
Limited AEG support
Weak output
Cannot recharge
But Wait, There’s More!
Click on Photo for More Information
To find out which battery voltage is best suited, be sure to check out the replica’s manual. The majority of AEG rifles that can run a 7.4V LiPo will be able to run either of the NiMHs; the reason being, a 7.4V LiPo is more powerful than a 9.6B NiMH. Do keep in mind only the expensive replicas or upgraded ones with better motors and gearboxes are able to run 11.1V LiPo batteries due to their immense power.
C Rating
You may have heard of C rating, it’s usually displayed next to the voltage number on a battery typically shown as 10c to 25c. How much power is discharged from the battery is all it means.
Basically, the higher that number is, means more burst of power the battery sends to the motor. The gears spin faster, thus providing a higher fire rate and trigger response. However, this will result in the battery running out of charge quicker. So in the end it’s a balance of looking for lifetime and performance. The majority of AEG out there are not able to handle anything more than 15c, so be sure to check the replica manual first!
Brick – Shaped like a flat/round rectangle, it’s commonly used for compact guns.
The battery connector is usually located in the buffer tube, inside the handguard, or even outside the handguard. So best ask around or visually inspect the replica to identify the battery space and which one will fit. As there are many different appearances and styles of batteries around. Choosing the right battery that’s able to run it and fit in is essential, as most airsoft AEG have limited battery space.
Nunchuck – Designed to fit in two small tubes in the stock.
Crane – Similar to the nunchuck, except it’s attached to two or three tubes of batteries.
Stick – Batteries lined up looking like a stick, always come as a single tub.
Large – Almost like the stick but lined up side by side and not as long.
Mini – This is a flat battery, smaller than the larger cousin.
PEQ – These types are stored in a battery pack and can be concealed in a PEQ box
How long to charge the airsoft battery?
Worried you’ll set your house on fire? Blowing yourself up with a battery? We will guide you through how to safely charge and handle your batteries! But first things first we recommend using a smart charger if possible, as it takes a lot of hassle and danger out of the equation. Don’t have one? We have a secret method to find out if your battery is fully charged and how long it should be charged.
Click on Photo for More Information
Don’t use an extension cord or a power strip if possible, this may be obvious but be sure the charger is plugged directly into the wall. If the power strip doesn’t have a built-in surge protector, a surge can potentially destroy the battery. Being safe is important!
How long to charge your airsoft battery depends on how many mAh it has. Of course, a 1400mAh will charge much faster than a battery with 2800mAh. Take a look at your charger, you will notice some information on the sticker. There should be an output rating on that sticker, something along the lines of “OUTPUT: DC 8.4v 300mA” which varies from brand to brand. The 300mAh means how much charge per hour so if you have a 3000mAh battery and a 300mAh charger, it’s simple mathematics from this point.
Battery Capacity (mAh) ÷ Output from charger = Hours
3000 ÷ 300 = 10
It’ll take ten hours to charge this completely dead/new battery to its full capacity. Simply just divide the mAh from the charger to the mAh of the battery! It can be left and claimed later but do keep an eye on it from time to time. This is a quick way to find out, but be aware this isn’t accurate since the battery might not be completely empty before charging. The temperature is also another factor that can affect how long a battery would take to charge. Using this formula is easy, but if you arent there whilst it’s charging or make the wrong calculations, there’s a chance the battery could get damaged.
How Do I Know The Battery Is Full?
How do we know if the battery is fully charged without a smart charger or voltmeter? Simple! Just touch the battery from time to time to check its temperature. Most likely fully charged if it’s warm, not lukewarm! Though if it’s hot to the touch then you may have damaged the battery, which isn’t good for your skin or battery. A stove that’s left on is similar to your battery being charged. Chances are chaos will be waiting for your return if it’s left unattended whilst you are away. So please guys if you do charge it like this, we ask you to watch over it like a baby!
Never ever rely on this method 100 percent of the time, we know it’s a lame technique but effective to check if the battery is charged. It’s not foolproof and in some freak situations, it may not work at all. If you plan on getting serious into airsoft, we recommend a smart charger should be the first major investment to your ever-growing collection of airsoft gear.
How to know when the airsoft battery is charged? The best and safest way to know when the airsoft battery is fully is by using a smart charger. But keep in mind that do not try to charge 2 battery packs at the same time unless the charger can support it. If the battery charger has more than 1 input, you should charge one at a time or you might damage the charger. Don’t skimp out on a charger, as the cheaper ones provide constant charge even when the battery is full!
It’s going to blow!
Here are a few things to take note of to protect you and others around in case something goes wrong. As using the wrong charger or wrong battery things can go south very fast so be careful if it’s your first time charging airsoft batteries. If your battery dies, remember to find a place to recycle them. This will prevent any harm done to kids or animals!
Never attempt to charge a non-rechargeable battery, the label on the sticker usually states what type it is.
Be sure to use the correct charger: look at what type of battery it is and what type of charger.
If there’s a hole in the battery or burn marks, dispose of them safely as they are faulty or damaged
Swollen up or fat batteries. This is the end of the line for the battery, get rid of it immediately.
If it’s swollen up like this, get rid of it fast!
If you plan on not using the airsoft batteries for several months (such as winter), it can ruin their lifespan. With some TLC, it’ll be kept for many years. Batteries naturally gradually discharge themselves if they are not in use for a long time. Especially if you leave the battery connected in your airsoft gun when not in use, this can drain them much faster. There’s a chance small electronic parts could corrode which results in permanent damage if unused daily. Not only that but if someone doesn’t know there’s a battery inside they might shoot someone by accident or break something. To be sure it works next time it’s out, fully charge the battery and left in an environment where the temperature is stable.
We hope this gives you a deep insight into how to charge an airsoft battery and wisdom about how they work. To find out more and learn more variety of batteries and chargers we have available.
How Long to Charge An Airsoft Battery
What is an airsoft battery?
Finally, your new airsoft gun arrives on your front porch, and you’re all excited to try it, but likely it doesn’t take standard AA batteries. Most Electric Airsoft guns require high-power rechargeable batteries, and you also need a battery charger to juice it up. The most popular Airsoft batteries are Lithium Polymer (LiPo) and Lithium-Ion (Li-Ion). But do you know how long to charge an Airsoft battery? Not all battery chargers are intelligent and know when to stop charging. Will I fry the battery, or worse yet, burn down the house? Read on as we give you a quick crash course on airsoft batteries and how to charge them.
Click on Photo for More Information
Most automatic electric guns (AEG) these days do not come with a battery or charger, so it’s a good idea to do some research before swiping that card. Depending on which AEG you buy, the connector type is different from brand to brand too. There are several different kinds of connector plug types, so keep in mind which one your gun uses when purchasing a battery. To save from buying all kinds of different batteries, you should consider standardizing on one plug type across all your AEGs so that your batteries are cross-compatible on all your Airsoft guns.
Mini Tamiya Connector.
Most standard AEGs come with a standard plastic semi-translucent connector plug known as mini-Tamiya. This plug type is very popular in R/C cars and planes. The benefit of using this type of plug is that they have a locking mechanism that prevents accidental disconnection. This connector physically isolates the positive and negative wires, which means it’s safer to use in damp environments. Safe for use in relatively low-current applications (up to about 15 A), the design provides safety and is fool-proof. If you like crawling around in the dirt or going prone, then the mud or water shouldn’t be able to penetrate this connector.
This is NOT a Mini Tamiya Connector! It’s a Tamiya connector.
The issue with these connectors is that the area of contact is small. Thus it can cause issues with the current flow, slightly decreasing your trigger response! Since they are made from softer nylon-based plastic, they can break quite easily and are not as durable as deans. Tamiya plugs are also bulky compared to deans plugs, which we will talk more about below. But Tamiya plugs are still popular in Japan, and hence Japanese made Airsoft guns will usually come with them.
Deans connector.
Moving on to the other type of connector is Deans. The connectors are based on big metal pieces shaped in the letter ‘T’, which lock into each other when connected. This provides a huge area of contact, which results in a higher flow of electrical current to the motor. Say hello to a higher fire rate and consistent electricity flow! They last longer than mini Tamiya as it’s constructed out of better materials. Slowly being phased out, Mini Tamiya is replaced by Deans.
In the airsoft community, one of the most common questions regarding airsoft batteries is “How long do I charge my battery for?”. Every battery is different, so there are no set rules on how long to charge it for.
We at Redwolf Airsoft have all kinds of batteries available, not to confuse you, we will stick to the ones we offer. If you own an RC model then you may notice they use very similar batteries. In fact, they are the same batteries!
What is the purpose of an airsoft battery?
Think of your AEG as an electronic device, mobile phone, shaver, wireless headsets, etc. They are all powered by one thing, a battery. This brings life into the products we use on a daily basis which applies to an AEG too. Without it, your AEG is as good as a mantlepiece in your home.
Known as mAh, or milliamp Hour, this is the number of energy batteries can store. Commonly used to measure the energy capacity of a battery, it’s a unit that measures (electric) power over time. In general, the more mAh there is, the longer the battery life which means more pew.
Let there be life!
So does this mean you’d want to find the one with the most capacity? Yes, but you have to make sure it can fit into your AEG! In most cases the more mAh, the bigger size of the battery. A good rule of thumb is to stick to something around 1500 mAh as they will most likely last a full day and fit most regular stocks. Just keep in mind if you’re trigger happy and enjoy beams of BBs at full auto then it may not last an entire day. We recommend a backup battery just in case; there’s nothing worse than running out of power during the final moments of a game and without a spare in sight!
Different kinds of airsoft batteries?
Nickel-metal hydride (NiMh), lithium-ion polymer (LiPo), nickel-cadmium (NiCad), and alkaline are the four types of batteries used in an AEG. Barely anyone uses NiCad or alkaline anymore as they are not as efficient or cost-effective.
Where do I start?
NiMH batteries are like your everyday rechargeable AA batteries, common, very safe, withstand cold weather, and hold charge well which can last for one to two years even when charged often. In recent years the trend in this type is transitioning away to current generation batteries which are similar to tablets or mobile phones (LiPo). NiMH batteries will self-discharge when left alone, especially in a warm environment. To squeeze more life out, it shouldn’t be fully depleted every game, though once in a while discharged fully.
Using a fast charger will likely heat it up before fully charged, unfortunately, they cant be quickly charged. A slow charge is much safer and healthier for these types.
Click on Photo for More Information
They also discharge much faster than any other when left standing, in high discharge applications it can’t reach their full potential. Charging them with more than 1.5 amps or quick discharges will damage the battery.
You may have heard the term “Memory Effect”, older generation batteries had problems as they memorized when it was discharged to a certain point repeatedly, causing a reduction in capacity. Fear not as current NiMH batteries on the market will not do that! It will come back to its full capacity after each and every charge. When overcharged it can be brought back to life by safely discharging, that’s why it’s preferred by many airsofters for its sheer reliability.
Pros Affordable
Commonly used in many AEG airsoft guns
Withstand cold weather
Longer lifespan Cons Slow charge
Discharge at a higher rate than other types
Slowly phasing out of the market
Lower energy capacity
Click on Photo for More Information
Holding way more charge and lasting longer compared to NiMH batteries, LiPo batteries are the most advanced battery on the market. Used practically everywhere including your mobile phone or tablet these are the current-gen of batteries. They come in two voltages, 7.2v or 11.2v perfect for an upgraded AEG that has a high rate of fire. If overcharged they can explode and cause chemical burns, fires, or even death in some cases. With an average price tag of $63 or more for just the battery and another $54 for the charger, it can be expensive. A lot of fraudulent sellers out there label their battery ratings incorrectly making them even more dangerous. So rest assured as we only sell quality, safe batteries, and chargers.
Unlike the NiMH battery type, there are no methods for optimal and healthy life of the LiPo battery, just make sure to never let it fully discharge. So as soon as your AEG starts to slow down and the gears turn slower with each shot, return to the safe zone and pop some new ones in.
Pros Unaffected by hot/cold
Commonly used in many AEG airsoft guns
Supports fast charge
Lighter than NiMH Cons Expensive
Dangerous if overcharged
Fragile
Require specific charger
Click on Photo for More Information
You may have heard of nickel-cadmium (NiCad) batteries, they are similar to the NiMh batteries but bulkier, heavier, and cant handle extreme temperatures well. What’s impressive about these is that they are able to quick charge and discharge with almost no damage done to the cells, perfect for guns that draw large energy and high rates of fire! Overcharging it can cause battery cells to split, leak, and even cause a fire so they should never be left alone even with a smart charger.
Pros Undamaged cells via charging/discharge
Lowest charging time out of all other types Cons Bulky and heavy
Prone to temperature changes hot/cold
Outdated
Only recharge when empty
Alkaline Batteries
Variety Of Alkaline Batteries.
The OG of batteries, alkaline. You won’t see this in airsoft these days because they cannot take the energy consumption from an AEG nor provide a high rate of fire. If stored in a room temperature (70F), or colder environment they can last years before losing even a sliver of a charge! Being very common this makes them way more affordable compared to NiMh or LiPo. Due to the chemical property, they can’t be recharged numerous times and can’t take the high voltage pull that AEG requires. Your pew time would be cut short as they barely have the capacity!
Pros Common
Hold charge for a long time Cons Limited capacity
Limited AEG support
Weak output
Cannot recharge
But Wait, There’s More!
Click on Photo for More Information
To find out which battery voltage is best suited, be sure to check out the replica’s manual. The majority of AEG rifles that can run a 7.4V LiPo will be able to run either of the NiMHs; the reason being, a 7.4V LiPo is more powerful than a 9.6B NiMH. Do keep in mind only the expensive replicas or upgraded ones with better motors and gearboxes are able to run 11.1V LiPo batteries due to their immense power.
C Rating
You may have heard of C rating, it’s usually displayed next to the voltage number on a battery typically shown as 10c to 25c. How much power is discharged from the battery is all it means.
Basically, the higher that number is, means more burst of power the battery sends to the motor. The gears spin faster, thus providing a higher fire rate and trigger response. However, this will result in the battery running out of charge quicker. So in the end it’s a balance of looking for lifetime and performance. The majority of AEG out there are not able to handle anything more than 15c, so be sure to check the replica manual first!
Brick – Shaped like a flat/round rectangle, it’s commonly used for compact guns.
The battery connector is usually located in the buffer tube, inside the handguard, or even outside the handguard. So best ask around or visually inspect the replica to identify the battery space and which one will fit. As there are many different appearances and styles of batteries around. Choosing the right battery that’s able to run it and fit in is essential, as most airsoft AEG have limited battery space.
Nunchuck – Designed to fit in two small tubes in the stock.
Crane – Similar to the nunchuck, except it’s attached to two or three tubes of batteries.
Stick – Batteries lined up looking like a stick, always come as a single tub.
Large – Almost like the stick but lined up side by side and not as long.
Mini – This is a flat battery, smaller than the larger cousin.
PEQ – These types are stored in a battery pack and can be concealed in a PEQ box
How long to charge the airsoft battery?
Worried you’ll set your house on fire? Blowing yourself up with a battery? We will guide you through how to safely charge and handle your batteries! But first things first we recommend using a smart charger if possible, as it takes a lot of hassle and danger out of the equation. Don’t have one? We have a secret method to find out if your battery is fully charged and how long it should be charged.
Click on Photo for More Information
Don’t use an extension cord or a power strip if possible, this may be obvious but be sure the charger is plugged directly into the wall. If the power strip doesn’t have a built-in surge protector, a surge can potentially destroy the battery. Being safe is important!
How long to charge your airsoft battery depends on how many mAh it has. Of course, a 1400mAh will charge much faster than a battery with 2800mAh. Take a look at your charger, you will notice some information on the sticker. There should be an output rating on that sticker, something along the lines of “OUTPUT: DC 8.4v 300mA” which varies from brand to brand. The 300mAh means how much charge per hour so if you have a 3000mAh battery and a 300mAh charger, it’s simple mathematics from this point.
Battery Capacity (mAh) ÷ Output from charger = Hours
3000 ÷ 300 = 10
It’ll take ten hours to charge this completely dead/new battery to its full capacity. Simply just divide the mAh from the charger to the mAh of the battery! It can be left and claimed later but do keep an eye on it from time to time. This is a quick way to find out, but be aware this isn’t accurate since the battery might not be completely empty before charging. The temperature is also another factor that can affect how long a battery would take to charge. Using this formula is easy, but if you arent there whilst it’s charging or make the wrong calculations, there’s a chance the battery could get damaged.
How Do I Know The Battery Is Full?
How do we know if the battery is fully charged without a smart charger or voltmeter? Simple! Just touch the battery from time to time to check its temperature. Most likely fully charged if it’s warm, not lukewarm! Though if it’s hot to the touch then you may have damaged the battery, which isn’t good for your skin or battery. A stove that’s left on is similar to your battery being charged. Chances are chaos will be waiting for your return if it’s left unattended whilst you are away. So please guys if you do charge it like this, we ask you to watch over it like a baby!
Never ever rely on this method 100 percent of the time, we know it’s a lame technique but effective to check if the battery is charged. It’s not foolproof and in some freak situations, it may not work at all. If you plan on getting serious into airsoft, we recommend a smart charger should be the first major investment to your ever-growing collection of airsoft gear.
How to know when the airsoft battery is charged? The best and safest way to know when the airsoft battery is fully is by using a smart charger. But keep in mind that do not try to charge 2 battery packs at the same time unless the charger can support it. If the battery charger has more than 1 input, you should charge one at a time or you might damage the charger. Don’t skimp out on a charger, as the cheaper ones provide constant charge even when the battery is full!
It’s going to blow!
Here are a few things to take note of to protect you and others around in case something goes wrong. As using the wrong charger or wrong battery things can go south very fast so be careful if it’s your first time charging airsoft batteries. If your battery dies, remember to find a place to recycle them. This will prevent any harm done to kids or animals!
Never attempt to charge a non-rechargeable battery, the label on the sticker usually states what type it is.
Be sure to use the correct charger: look at what type of battery it is and what type of charger.
If there’s a hole in the battery or burn marks, dispose of them safely as they are faulty or damaged
Swollen up or fat batteries. This is the end of the line for the battery, get rid of it immediately.
If it’s swollen up like this, get rid of it fast!
If you plan on not using the airsoft batteries for several months (such as winter), it can ruin their lifespan. With some TLC, it’ll be kept for many years. Batteries naturally gradually discharge themselves if they are not in use for a long time. Especially if you leave the battery connected in your airsoft gun when not in use, this can drain them much faster. There’s a chance small electronic parts could corrode which results in permanent damage if unused daily. Not only that but if someone doesn’t know there’s a battery inside they might shoot someone by accident or break something. To be sure it works next time it’s out, fully charge the battery and left in an environment where the temperature is stable.
We hope this gives you a deep insight into how to charge an airsoft battery and wisdom about how they work. To find out more and learn more variety of batteries and chargers we have available.
So you have finished reading the how to charge airsoft lipo battery topic article, if you find this article useful, please share it. Thank you very much. See more: how to charge a lipo battery, how to charge airsoft battery without charger, charging a 4s lipo battery, airsoft battery charger, titan digital lithium battery charger error codes, how to store airsoft battery, how to charge titan battery, airsoft lipo battery guide
