You are looking for information, articles, knowledge about the topic nail salons open on sunday near me how to fix a trumpet that won t play on Google, you do not find the information you need! Here are the best content compiled and compiled by the https://chewathai27.com team, along with other related topics such as: how to fix a trumpet that won t play why won’t my trumpet play, trumpet valve, how to fix loose trumpet valves, why does my trumpet sound weird, how to play trumpet, how to oil trumpet valves, trumpet notes, why does my trumpet sound spitty
Contents
Why is my trumpet not making sound?
Air blown into the trumpet refuses to pass through, rendering the instrument unplayable. While there are many possible causes, it’s most likely that one or more of the valves has been turned from its proper position, blocking the air flow.
How do you get a trumpet to work?
When playing a trumpet you can change the sound it produces just by how your lips vibrate when blowing-no fingers required. To produce low notes, vibrate your lips slowly; the higher the note you want to play, the quicker you will need to vibrate your lips.
How much does it cost to fix a trumpet?
| Brass Repair Pricing Prices do NOT include parts. | ||
|---|---|---|
| Instrument | General Service | Overhaul Student Instruments |
| Trumpet or Cornet | $60-$90 | $550 |
| Single Horn (3 Valves) | $90-$125 | $1,065 |
| Double Horn (4 Valves) | $60-$90 | $1,540 |
Do trumpet valves wear out?
If your trumpet is brand new, you probably won’t have many issues. But, once you start using it frequently your trumpet could suffer from leaking valves. Usually the result of normal wear and tear, air that leaks out between the valve and casing can affect your trumpet’s response.
Does playing trumpet damage your lips?
Tissue damage can occur if the mouthpiece is forced against the lips too hard or if one plays too long or with too much pressure without rest. More serious lip damage can occur from overuse without warming up, as in Hubbard’s case.
How old is my trumpet?
Trumpets will usually have a serial number on either side of their center valve. Depending on the brand, the serial number can tell you when or where the trumpet was made, allowing you to determine its vintage status and age.
Why is my trumpet valve stuck?
The valves are too sticky.
This can occur if the oil has caused debris to loosen in the trumpet valve case. It can be fixed by pulling the valve out and thoroughly wiping it with a clean cloth. It will then need to be oiled again before being re-inserted.
What is the hardest instrument to play?
- Violin. The violin is a wooden stringed instrument that’s part of a larger family of similar instruments. …
- The French Horn. …
- The Organ. …
- Bagpipes. …
- Accordion. …
- Oboe. …
- Harp. …
- Guitar.
Who blew the trumpet in the Bible?
They did this for six days. On the seventh day, they got up at daybreak and marched around the city seven times in the same manner, except that on that day they circled the city seven times. The seventh time around, when the priests sounded the trumpet blast, Joshua commanded the people, “Shout!
What animal is trumpet?
…
| Sound | Animal |
|---|---|
| 1. Trumpet | A. Bee |
| 2. Clatter | B. Elephant |
| 3. Buzz | C. Monkey |
Why is my trumpet Spitty?
Dry, chapped lips could also be the reason for the inability to play softly. Additionally, swollen lips or excessive mouthpiece pressure can be the cause of this issue.
Why is my trumpet flat?
If the needle is pointed to the left, the note is flat. That means that the note you are playing is lower (even incrementally) than where it should be. This means that you need to make an adjustment to the length of your trumpet by pushing in the main tuning slide to raise the pitch.
Why is my trumpet raspy?
The sound from the trumpet IS caused by the vibrating of our lips. Air in the sound IS caused from too big an aperture for the note/volume we are playing. What happens is that some of the air gets through the hole without touching any lip tissue and doesn’t get put into vibration.
Help! My Trumpet Isn’t Working! (Or sounds weird…) – YouTube
- Article author: www.youtube.com
- Reviews from users: 29538
Ratings - Top rated: 5.0
- Lowest rated: 1
- Summary of article content: Articles about Help! My Trumpet Isn’t Working! (Or sounds weird…) – YouTube Updating …
- Most searched keywords: Whether you are looking for Help! My Trumpet Isn’t Working! (Or sounds weird…) – YouTube Updating Is your trumpet making a strange sound? Or not working at all? Many times, this is caused by the trumpet valves being out of place. In this tutorial, Mr. Se…trumpet, broken, sounds weird, fix trumpet
- Table of Contents:
How To Fix Trumpet Valves – YouTube
- Article author: www.youtube.com
- Reviews from users: 47776 Ratings
- Top rated: 4.8
- Lowest rated: 1
- Summary of article content: Articles about How To Fix Trumpet Valves – YouTube Updating …
- Most searched keywords: Whether you are looking for How To Fix Trumpet Valves – YouTube Updating How to fix trumpet valves that have come unscrewed.Valves, buttons, stems, valve springs, Valve seats, unscrewed
- Table of Contents:
How to Play the Trumpet:Techniques for playing the trumpet – Musical Instrument Guide – Yamaha Corporation
- Article author: www.yamaha.com
- Reviews from users: 9740 Ratings
- Top rated: 4.9
- Lowest rated: 1
- Summary of article content: Articles about How to Play the Trumpet:Techniques for playing the trumpet – Musical Instrument Guide – Yamaha Corporation Updating …
- Most searched keywords: Whether you are looking for How to Play the Trumpet:Techniques for playing the trumpet – Musical Instrument Guide – Yamaha Corporation Updating Musical Instrument Guide,Trumpet,How to Play the Trumpet:Techniques for playing the trumpetThis is the Yamaha Corporation [Musical Instrument Guide] website. This article contains information about the Trumpet [How to Play the Trumpet:Techniques for playing the trumpet]
- Table of Contents:
Blowing techniques
How to blow into the mouthpiece
How to hold the trumpet
How to blow (Toh Tay Tee)
Producing sound with fingering
Musical Instrument GuideTrumpet Contents
How to Play the Trumpet:Techniques for playing the trumpet – Musical Instrument Guide – Yamaha Corporation
- Article author: medium.com
- Reviews from users: 30815 Ratings
- Top rated: 4.2
- Lowest rated: 1
- Summary of article content: Articles about How to Play the Trumpet:Techniques for playing the trumpet – Musical Instrument Guide – Yamaha Corporation Remove the tuning sle and blow through the trumpet, from the end of the leadpipe. If airflow is blocked, run a cleaning snake brush (image below) through the … …
- Most searched keywords: Whether you are looking for How to Play the Trumpet:Techniques for playing the trumpet – Musical Instrument Guide – Yamaha Corporation Remove the tuning sle and blow through the trumpet, from the end of the leadpipe. If airflow is blocked, run a cleaning snake brush (image below) through the … Musical Instrument Guide,Trumpet,How to Play the Trumpet:Techniques for playing the trumpetThis is the Yamaha Corporation [Musical Instrument Guide] website. This article contains information about the Trumpet [How to Play the Trumpet:Techniques for playing the trumpet]
- Table of Contents:
Blowing techniques
How to blow into the mouthpiece
How to hold the trumpet
How to blow (Toh Tay Tee)
Producing sound with fingering
Musical Instrument GuideTrumpet Contents
Learning Trumpet: Problems Getting Started – Trumpet Heroes
- Article author: trumpetheroes.com
- Reviews from users: 45912 Ratings
- Top rated: 3.7
- Lowest rated: 1
- Summary of article content: Articles about Learning Trumpet: Problems Getting Started – Trumpet Heroes Check that first. Try to gently turn the valve caps clockwise. If they don’t turn they’re probably in right. If one rotates and then … …
- Most searched keywords: Whether you are looking for Learning Trumpet: Problems Getting Started – Trumpet Heroes Check that first. Try to gently turn the valve caps clockwise. If they don’t turn they’re probably in right. If one rotates and then … Here are some of the most common problems when getting started learning trumpet: Learning Trumpet: Common Problems Air won’t move through the trumpet at all.My…
- Table of Contents:
Learning Trumpet Common Problems
About Jim
how to fix a trumpet that won t play
- Article author: www.quora.com
- Reviews from users: 13762 Ratings
- Top rated: 4.5
- Lowest rated: 1
- Summary of article content: Articles about how to fix a trumpet that won t play Most people with an airy tone also find it very hard to play SOFTLY, because the same inefficient lip aperture that causes the airiness also won’t let you play … …
- Most searched keywords: Whether you are looking for how to fix a trumpet that won t play Most people with an airy tone also find it very hard to play SOFTLY, because the same inefficient lip aperture that causes the airiness also won’t let you play …
- Table of Contents:
Help! My Child’s Brass Instrument Won’t Play! – Music Education Blog for Parents and Students | Vibe Music Academy
- Article author: www.vibemusicacademy.com
- Reviews from users: 36043 Ratings
- Top rated: 4.2
- Lowest rated: 1
- Summary of article content: Articles about Help! My Child’s Brass Instrument Won’t Play! – Music Education Blog for Parents and Students | Vibe Music Academy To fix this problem, unscrew the top valve cap, remove the valve and apply valve oil to the spring and the valve shaft and return it to the … …
- Most searched keywords: Whether you are looking for Help! My Child’s Brass Instrument Won’t Play! – Music Education Blog for Parents and Students | Vibe Music Academy To fix this problem, unscrew the top valve cap, remove the valve and apply valve oil to the spring and the valve shaft and return it to the … Dealing with malfunctioning brass instruments can be intimidating, but
fortunately, most common problems can be fixed at home with the supplies in
your student’s instrument case. Below, I have listed the most common
problems for brass instruments and their solutions. - Table of Contents:
Instruments
Teachers
music lessons
reviews
EVENTS
blog
jobs
(317) 395-3001
See more articles in the same category here: 721+ tips for you.
Why won’t my trumpet blow? Checking for and Correcting a Turned Valve
The most common issue encountered by beginning trumpet students is an apparent jam in the trumpet. Air blown into the trumpet refuses to pass through, rendering the instrument unplayable. While there are many possible causes, it’s most likely that one or more of the valves has been turned from its proper position, blocking the air flow. This post details the most common causes of this problem, and how to fix them.
Valves
When diagnosing the cause of blocked airways in the trumpet, it is important to pay attention to some aspects of the trumpet valve.
[b]1. Valve Numbers[/b]In most cases, trumpet valves are numbered, with “1” being the closest to the mouthpiece, and “3” being the closest to the bell. If the valves are not numbered, try and match up the openings on each valve with the pipes on the outside of each valve casing, as detailed in the image below. It is very important that the valves are inserted in the proper order, as each is designed specifically to match the openings within the valve casings.
[img]http://farm7.static.flickr.com/6024/6002456532_da40a09a7f.jpg[/img] [b]2. Valve Guides[/b]On either side of each valve are small, usually plastic parts, located just under the stem. These parts, called valve guides, hold the valve in place inside the trumpet. To ensure that your valves are aligned properly within each valve casing, line up the valve guides with each other, and make sure that each valve is facing the same direction as the others (often, one valve guide is smaller than the other, allowing you to differentiate one side from the other). In most cases, the valve guides face either side of the trumpet, away from both the bell and mouthpiece.
[img]http://farm7.static.flickr.com/6149/6002456456_1684ab89b7.jpg[/img] [b]Fixing the Problem[/b]Begin by removing all three valves from the trumpet. If, at this point, the trumpet still does not blow freely, skip ahead to “Clearing a Block.”
Insert the 3rd trumpet valve into the casing closest to the bell, rotating it until the horn blows freely regardless of the valve’s up/down position; the valve guides should click the valve into place. Repeat this process with the 2nd, and finally 1st valve. At this point, air should pass freely through the trumpet.
All three valves removed:
[img]http://farm7.static.flickr.com/6014/6002456584_8a1df654ce_z.jpg[/img]Third Valve in Trumpet properly aligned:
[img]http://farm7.static.flickr.com/6127/6001908231_78e9e04ed2_z.jpg[/img]Second Valve Next:
[img]http://farm7.static.flickr.com/6015/6002456402_886285b5ee_z.jpg[/img]First Valve Last:
[img]http://farm7.static.flickr.com/6127/6001908139_8d8de9b918_z.jpg[/img]TIP: When lining up the valves, it may be helpful to take note of the position of the number etched on the valve; they often point directly toward the mouthpiece when correctly lined up for brands such as Bach, Jupiter, Yamaha, LJ Hutchen, etc. With that said, some manufacturers etch the valve numbers so they face sideways, and others so they face the bell. If once your 3rd valve is “locked” in no air will pass through the trumpet, then try rotating it 90 degrees.
[b]Clearing a Block[/b]If all the valves have been checked and still the trumpet refuses to play, there is likely a blockage of some sort within the instrument. Blocks causing a complete stoppage of airflow are likely to occur before air reaches the valves, so take a moment to identify the location of the block. Remove the tuning slide and blow through the trumpet, from the end of the leadpipe. If airflow is blocked, run a cleaning snake brush (image below) through the leadpipe to clear the blockage until you can blow through it freely. If the blockage is not located, repeat this process for the tuning slide itself. If the blockage still cannot be located, the aid of a musical instrument repair professional may be needed.
The most common issue encountered by beginning trumpet students is an apparent jam in the trumpet. Air blown into the trumpet refuses to pass through, rendering the instrument unplayable. While there are many possible causes, it’s most likely that one or more of the valves has been turned from its proper position, blocking the air flow. This post details the most common causes of this problem, and how to fix them. When diagnosing the cause of blocked airways in the trumpet, it is important to pay attention to some aspects of the trumpet valve.
1. Valve Numbers
In most cases, trumpet valves are numbered, with “1” being the closest to the mouthpiece, and “3” being the closest to the bell. If the valves are not numbered, try and match up the openings on each valve with the pipes on the outside of each valve casing, as detailed in the image below. It is very important that the valves are inserted in the proper order, as each is designed specifically to match the openings within the valve casings.
2. Valve Guides
On either side of each valve are small, usually plastic parts, located just under the stem. These parts, called valve guides, hold the valve in place inside the trumpet. To ensure that your valves are aligned properly within each valve casing, line up the valve guides with each other, and make sure that each valve is facing the same direction as the others (often, one valve guide is smaller than the other, allowing you to differentiate one side from the other). In most cases, the valve guides face either side of the trumpet, away from both the bell and mouthpiece.
3. Fixing the Problem
Begin by removing all three valves from the trumpet. If, at this point, the trumpet still does not blow freely, skip ahead to #4, “Clearing a Block.”
Insert the 3rd trumpet valve into the casing closest to the bell, rotating it until the horn blows freely regardless of the valve’s up/down position; the valve guides should click the valve into place. Repeat this process with the 2nd, and finally 1st valve. At this point, air should pass freely through the trumpet.
TIP: When lining up the valves, it may be helpful to take note of the position of the number etched on the valve; they often point directly toward the mouthpiece when correctly lined up for brands such as Bach, Jupiter, Yamaha, LJ Hutchen, etc. With that said, some manufacturers etch the valve numbers so they face sideways, and others so they face the bell. If once your 3rd valve is “locked” in no air will pass through the trumpet, then try rotating it 90 degrees.
All three valves removed
Third valve properly aligned
Second valve properly aligned
First valve properly aligned
4. Clearing a Block
If all the valves have been checked and still the trumpet refuses to play, there is likely a blockage of some sort within the instrument. Blocks causing a complete stoppage of airflow are likely to occur before air reaches the valves, so take a moment to identify the location of the block. Remove the tuning slide and blow through the trumpet, from the end of the leadpipe. If airflow is blocked, run a cleaning snake brush (image below) through the leadpipe to clear the blockage until you can blow through it freely. If the blockage is not located, repeat this process for the tuning slide itself. If the blockage still cannot be located, the aid of a musical instrument repair professional may be needed.
Yamaha Vinyl-Coated Trumpet Cleaner
Common Repairs for Trumpets
Since the various components of a trumpet must work together in order for the instrument to function and play properly, it’s not uncommon for problems to arise. Fortunately, the trumpet is a fairly simple mechanism and the problems you’ll run into are pretty universal. Experiencing problems with the trumpet and its various components is a normal part of owning the instrument, and many of the issues can quickly and easily be fixed by a qualified repair technician. From stuck mouthpieces and sticking valves to broken solder joints and stuck slides, here are a few of the most common repairs for trumpets.
Stuck Mouthpieces
Not exclusive to the trumpet, stuck mouthpieces are also experienced by trombonists, saxophonists, and pretty much any other brass musician whose instrument uses a mouthpiece. Since mouthpiece shanks go from narrow to wide, it’s easy for them to get stuck over time. When the mouthpiece is first placed in the trumpet it fits snugly but, if it gets accidentally bumped or pushed in further, it’ll get wedged and won’t come out. Most new trumpet players assume they can unstick the mouthpiece with a pair of pliers or vice grips, but these are exactly the wrong type of tools to use. Trumpet brass is soft and bends easily, so don’t try to fix this on your own: repair technicians have a special tool that’s used specifically to unstick stuck mouthpieces without damaging the instrument.
The Warburton Anchor Grip Trumpet and Cornet Mouthpiece Tops are arranged in a progression from large to small in ascending numerical order. The Anchor Grip Tops are designed for players with thick or fleshy lips that desire a mouthpiece that seats more securely and allows the player to have improved tonguing performance. The Warburton Anchor Grip Trumpet and Cornet Mouthpiece Tops are arranged in a progression from large to small in ascending numerical order. The Anchor Grip Tops are designed for players with thick or fleshy lips that desire a mouthpiece that seats more securely and allows the player to have improved tonguing performance.
Air Leakage
If your trumpet is brand new, you probably won’t have many issues. But, once you start using it frequently your trumpet could suffer from leaking valves. Usually the result of normal wear and tear, air that leaks out between the valve and casing can affect your trumpet’s response. To reduce air leakage, you can try using a heavier valve oil. If that doesn’t work, take your trumpet into the shop for valve work or a full replacement. Even if you come across replacement parts on sites like eBay or Craigslist, leave this repair to the professionals. Not only do they know exactly what they’re doing, but they have access to the right parts and tools.
Sticky Valves
At one point or another the valves of your trumpet are sure to stick. While valves usually move up and down to facilitate the act of playing, the valves may get stuck at certain places. In addition to ruining the sound, sticking valves will make it more difficult to play. If you think your valves are stuck, the best way to handle the situation is to use a good quality valve oil and to keep them as lubricated as possible. If you play or practice the trumpet every day you should oil the valves of your trumpet at least once a week, while you’ll need to oil your valves less often if you only play the trumpet a couple times a week. Your band or orchestra teacher should be able to provide you with advice about how often you should oil your valves and which valve oil you should be using.
This 8 oz. bottle is to refill the valve oil in MusicNomad’s 2 oz. dropper bottle (sold separately). This innovative, premium formula is like no other. Scientifically designed to provide fast, long-lasting valve action, MusicNomad’s Valve Oil does not build up while protecting against rust and corrosion. The synthetic ingredients used are biodegradable, non-toxic, odorless and petroleum free. This 8 oz. bottle is to refill the valve oil in MusicNomad’s 2 oz. dropper bottle (sold separately). This innovative, premium formula is like no other. Scientifically designed to provide fast, long-lasting valve action, MusicNomad’s Valve Oil does not build up while protecting against rust and corrosion. The synthetic ingredients used are biodegradable, non-toxic, odorless and petroleum free.
Broken Solder Joints
Since this repair involves a gas torch, it definitely shouldn’t be tried at home. Broken solder joints happen when a trumpet is twisted or dropped, and can be fixed by straightening whatever is bent. This is done by heating the joint with a gas torch until it’s hot enough to melt the solder, but cool enough to prevent damage to the finish. From here, the repair technician will solder across the whole joint and, when the solder cools, the repair technician will clean all around it. Since the repair technician cleans the area surrounding the joints, this part of your trumpet should look as good as new once the repair is complete.
A Stuffy Sound
If you’re noticing that a clogged or stuffy sound is coming from your instrument, don’t worry- it’s a common problem that’s usually related to the trumpet’s valves. To find and eliminate the problem check the valves to ensure none of the corks, felts, or spacers are worn down. If this isn’t the issue, the water key could be broken or leaking, or the valves may have been mixed up after cleaning the trumpet. The valves are numbered 1 to 3, and the first should be closest to the mouthpiece. If the valves are in order and none of the mechanisms are worn down, check for air leakage and make sure a foreign object isn’t stuck in the trumpet. If none of the above seem to be the issue, your teacher or a qualified repair technician may be able to provide more guidance.
Stuck Slides
Although stuck slides can be caused by an accident or bump, in most cases they’re caused by the chemical bonding of impurities left on them. For this reason, it’s important to keep your trumpet clean and well maintained. Sometimes the stuck slides will come apart with pressure, but don’t apply the pressure with a hammer or pliers, as these are too tough for the soft metal of a trumpet. Repair technicians have a variety of tactics they can try, including heat application and complete disassembly and reassembly of the trumpet. These may sound complicated (they are!) but if the technician is experienced your trumpet will look and sound the same way it did before.
The Bach 1877 Trumpet Repair and Maintenance Kit contains the most common repair parts for Bach Stradivarius trumpets. Kit includes water key springs, valve felts, stem felts, and more. The Bach 1877 Trumpet Repair and Maintenance Kit contains the most common repair parts for Bach Stradivarius trumpets. Kit includes water key springs, valve felts, stem felts, and more.
Dents
Even if you never transport your trumpet to or from your home, a dent or two is bound to happen. Using special mandrels and other tools, a good technician can rub and pound out the dent until the metal is smooth again. In some cases, this type of work can be performed by a general metalworker in lieu of an instrument technician, but an instrument technician is recommended as they’ll handle your instrument with the care it deserves. If the trumpet’s finish or lacquer wasn’t damaged in the accident, you’ll have to look very closely to even see where the dent originally was.
If you need help finding someone to fix your instrument, head to Music & Arts or learn Hotru,w to Find a Qualified Repair Technician.
Was this article helpful? Yes No
Help! Emergency Trumpet Repair Tips
Disasters and near disasters seem to always happen at the worst times and for that reason, I thought I would share some quick fixes for occasions such as these.
Your second valve will not go down
Have you ever had this happen? The count off begins “ONE, TWO, ONE TWO THREE FOUR”. And you discover your second valve won’t go down! It has happened to me and it is not a pretty sight. After the panic has subsided, you look down the page to see when you can rest and get it working again. Panic again! You have no rests for the next three years! Your brain races feverishly for an answer, then you realize you’ll be OK. This piece is written in the key of Eb concert and there are no F#’s or B’s so you are home free. Every note with 1st and 2nd fingerings can be played with your third valve. That low Ab and the low Eb can be played third valve with the third slide extended. PIECE OF CAKE!
Stuck Trumpet Mouthpiece
Although this is much less a disaster than the first situation, it does mean that you can’t put your horn in the case when you leave the theater. A mouthpiece can get stuck because of many reasons. I remember one time in Iowa when we were playing the Ringling Brothers, Barnum and Bailey Circus and the third chair player got his mouthpiece stuck because he had used too much mouthpiece pressure playing his part. I wonder what his horn would have looked like if he were playing the first part.
Removing a stuck mouthpiece can be a serious problem and a professional repairperson could be required, but for the less drastic removals, try this-
Place the mouthpiece in the jam of a WOODEN DOOR and a WOODEN DOOR JAM. Please take note that I said a WOODEN DOOR and a WOODEN DOOR JAM. If you use a metal door and door jam, you will ruin your mouthpiece.
Close the door SLIGHTLY on the mouthpiece.
Next tap the mouthpiece receiver (metal around the mouthpiece) LIGHTLY with a wooden or plastic item (screw driver handle works).
If mouthpiece does not come out, place the mouthpiece receiver under WARM water for a few minutes and the repeat the previous steps.
If this does not release the mouthpiece you will have to find a repairman with a mouthpiece puller.
Water Key Spring Broke
I don’t know how those things know when to break but it is always before a concert. Make sure you have a few rubber bands in your repair kit. If you are playing a Schilke or a Yamaha, it is a simple repair. Double up the rubber band and slip it down your tuning slide onto the water key. If you are playing an instrument that has a brace in the way, like a Bach, get it on there any way you can.
This is only a temporary fix for if you leave the rubber band on for any length of time, the moisture will get between the band and your horn and will eventually tarnish the area. I remember one student many years ago who played in one of my jazz bands. Every rehearsal he would show up with a cigarette stuffed between the water key lever and the tuning slide. I think he played that way for several years. HE WAS NOT ONE ON MY STUDENTS.
You just “oiled your valves” and now you can’t get air through your horn
Don’t panic. The fix is quick and easy.
Blow air into your horn.
As you continue to blow air, press down each valve.
The depressed valve that changes the sound will be the one that has not been seated properly and needs to be rotated.
You just “washed your horn” and now you can’t get air through it
Most often when this happens, the valves have been inserted into the wrong valve casing.
Take all three valves out and check the number stamped on each.
Replace them in the correct valve casings.
Every time you push your valves “down” they make a clanking sound
Replace the pads under your finger buttons (seen from the outside of the horn)
Every time your valves “come up” they make a clanking sound
Unscrew and remove the finger button on the offending valve(s)
Remove the upper valve cap under the finger button
Replace the felt pad under the upper valve cap
Sometimes your valves won’t go up and down smoothly
Join the club! Sticking valves (a temporary but still frustrating occurrence) are usually caused by one of three situations, 1. The valves are dirty and need to be cleaned, 2. The valve casing has been damaged, and #3. The valves could be worn out. Cleaning is a simple solution in case #1. Case #2 usually requires the services of a qualified repairman. The third condition will in most cases require a repairman also but before you take it in to the shop, try this trick-
Remove the sticking valve
Wash it thoroughly with warm, soapy water
Dry it off completely
Take a Qtip or a ball of cotton and apply a thin coat of RainX to the valve
After it has dried, buff it with a lint free cloth
Re-oil the valve and replace it in the instrument
I have had very good results with this process especially on older or cheaper horns. I do not suggest this process on a top line instrument but if you are fed up with sticking valves on your favorite horn and want to try it, let me know how it works for you. I have no problem using it on older horns but have not tried it on my bread and butter horns.
You have trouble getting the inside of your mouthpiece really clean
Next time put some tooth paste on you mouthpiece cleaning brush when you clean it. Make sure that you wash it out completely before you put it in your horn. You don’t want any paste to get into your valves.
You can’t remove a valve slide
Run the end of a cloth (hanker chief will work- remember those things? I keep mine in the same drawer that I store my eight track tapes) through the bend in the slide and extend it to the middle so you can grasp both ends
Pull gently on the cloth and hopefully this will pop the slide out
If this does not work, put some penetrating oil on it and let it set overnight and try again the next day
When I replace my valve slides after cleaning, I make sure that I don’t shove them all the way in. I usually leave a space the thickness of a piece of paper. If I get in the situation where the slide becomes stuck, the small opening will allow me to more easily get penetrating oil in and it also gives me the options of either pulling the slide out or pushing it in.
I’m sure there will be some of you who also have tricks which have helped you and/or your students through the years. If you have some hints, please send them so that we will be able to help others. Fill out the comment section at the bottom and send it on.
Do you have any Emergency Repair stories or Tips? Add yours in the comments section below.
So you have finished reading the how to fix a trumpet that won t play topic article, if you find this article useful, please share it. Thank you very much. See more: why won’t my trumpet play, trumpet valve, how to fix loose trumpet valves, why does my trumpet sound weird, how to play trumpet, how to oil trumpet valves, trumpet notes, why does my trumpet sound spitty
