Are you looking for an answer to the topic “hot tub drain plug“? We answer all your questions at the website Chewathai27.com/ppa in category: Top 867 tips update new. You will find the answer right below.
Table of Contents
How to drain (empty) a spa by gravity if you do not have a submersible pump
See some more details on the topic hot tub drain plug here:
How to Drain a Hot Tub
Here’s the good news: The chemical additive you use to purify the water, be it chlorine or bromine, keeps the water clean for three months or more depending on how often you use the tub, so you don’t have to empty it more often than the. But you’re going to want to replace the water and start fresh every few months or so, or your hot tub will look and feel pretty dirty — or, even worse, become contaminated with bacteria.
Methods for draining a hot tub
There are three methods for draining a hot tub: through the drain cock (also known as the drain plug), with a submersible pump, or with the help of a wet/dry vacuum. However, before you begin draining the tub, be sure to disconnect power to prevent the jets and pumps from being accidentally turned off during this process.
Also check the ordinances in your area for guidelines or restrictions on disposing of chemically treated water. Some cities may have laws about dumping pool or hot tub water onto the street or into your own yard.
Use of the drain socket
Your spa is equipped with a drain fitting, which is located on the outside of the tub near the bottom rim. (Some models have two vents, a main vent and an auxiliary vent. The main vent is used to drain the spa; the auxiliary vent is used to bleed the internal lines.)
If your drain faucet is directly above a drain in the floor, simply open the valve to allow water to flow down the drain. If the drain or sewer is further away, attach a garden hose to the faucet, position the other end of the hose over the drain, and open the valve. Note that if your drain or sewer is uphill from your hot tub, you will need a submersible pump to completely drain the tub.
It should take an hour or two for the entire tub to drain through the faucet. Depending on the contour of the tub, you may end up with a few puddles of water. If you don’t have a wet/dry vacuum to vacuum up these puddles, use your hands or a brush to scoop the water to the interior drain.
Using a submersible pump
This is a faster way to drain a hot tub since the pump forces the water out.
Begin by attaching a drain hose to the pump, then lay the pump flat on the bottom of the spa center. Check that the other end of the hose is long enough to reach the nearest drain or sewer. If this is not the case, attach a garden hose to the drain hose to lengthen it. Then just turn on the pump and let it remove the water.
To deal with the leftover puddles of water at the end, place the pump directly in a puddle to suck out the water. However, keep an eye on the pump to make sure it’s always sucking in water, as too much air can cause the pump to overheat.
Using a wet/dry vacuum
This method is slower than using a submersible pump, but faster than using the drain spout.
Attach the wet/dry vacuum hose to the machine and hold the open end of the hose in the water. Turn on the vacuum to allow water to flow through the hose. Once it does, turn off the vacuum and disconnect the hose from it. The water should keep flowing. Position the open end of the hose over a drain or sewer so water can flow directly into it.
Once the water becomes too shallow to vacuum effectively, reconnect the hose to the wet/dry vacuum and use it to vacuum up the remaining water. Make sure you vacuum up any small puddles of water at the end.
How to Drain a hot tub
With the changing of the seasons, it’s the perfect time to drain and clean your hot tub. But wait! Do you know how to drain a hot tub?
Your hot tub (most likely) has a built in drainage feature! This post covers the brands we stock in our hot tub showrooms, so consult your owner’s manual if you don’t have one of the following models:
How to drain a hot tub
Before draining and cleaning your hot tub,
Make sure your spa is turned off!
Hot Spring Collection (Highlife and Limelight models)
If you look at your hot tub’s main controls, you should see a drain cap at the bottom of the hot tub. Remove the cap and you will see a hose barb/valve.
Screw your garden hose onto the nozzle
There is a small knob on the drain valve that you can turn to start the flow of water, which drains by gravity
Hot Spring Highlife spas only: When the water is almost completely drained, unscrew the cap on the secondary drain to remove the remaining water.
Once the water is drained, turn off the knob, remove your garden hose and screw the drain cap(s) back on.
Hot Spot and Caldera Vacanza series
Remove your spa’s front panel (this is the panel below your main controls)
Locate the drain cap. Raise the white drain hose above the water level (requires cutting the plastic tie the first time).
Unscrew and remove the drain cap.
Attach the drain hose to the garden hose and route it to a suitable drainage area. (Keep the hose below the waterline.)
Once the water is drained, remove your garden hose and reattach the drain cap.
Replace the spa cabinet panel.
Caldera Spas
Locate the main drain valve for your spa (check the left corner on the front of your spa)
Pull the handle until you reach the middle position. Once there, twist the handle slightly to fully extend the drain tube. Then remove the drain cap.
Attach a garden hose to the end of the drain
Slide the garden hose and drain pipe halfway back to the hot tub. This will start the water flow
Unscrew the black cap, unscrew the nozzle, gently pull the hose out of the nozzle to open the water flow
When the water is drained, pull and remove the garden hose, replace the drain cap and push the drain tube back into the hot tub!
Sundance 880 and 780 Series Spas
Locate the 3-inch gray drain valve cap on the side of the spa body. Unscrew the drain valve cap to reveal the male garden hose fitting underneath
Attach the female end of the garden hose to the drain fitting and route the other end of the garden hose away from the spa
Pull the end of the garden hose outward (about 3/8″) at the drain fitting to open the drain valve and drain water from the spa
After the spa has drained, close the drain valve by pushing the end of the garden hose inward at the drain connector until you feel it bottom.
Before refilling the spa, remove the garden hose and install the gray drain cap.
Extra tip: The quickest way to drain a hot tub is with a submersible pump. Available at any hardware store, this small pump will drain your hot tub quickly. Once you get to the bottom of the hot tub there is water left over which you have to remove manually as the pump can’t remove all the water but it does a great job!
Did you know our factory certified technicians can take care of your hot tub for you! Inquire about our Spa Valet service to have your hot tub serviced weekly or just once!
CleverSpa Hot Tub Drainage Plug
Delivery will be made in 2-3 days, excluding holidays and weekends. Please note that we only deliver to mainland UK*.
Separate charges apply to all orders outside of the UK.
Delivery is FREE on all orders over £80 (within UK mainland). Delivery is by Parcel Force Tracked (weekdays).
For orders under £80, Parcel Force delivery costs £4.95.
Please see our Delivery and Returns pages for more information.
Related searches to hot tub drain plug
Information related to the topic hot tub drain plug
Here are the search results of the thread hot tub drain plug from Bing. You can read more if you want.
You have just come across an article on the topic hot tub drain plug. If you found this article useful, please share it. Thank you very much.
