How To Tape A Color Guard Rifle? Quick Answer

Are you looking for an answer to the topic “how to tape a color guard rifle“? We answer all your questions at the website Chewathai27.com/ppa in category: Aodaithanhmai.com.vn/ppa/blog. You will find the answer right below.

This little bit of extra care allows your rifle to withstand more shock without cracking. Wrap separate pieces of strapping tape all the way around the nose (1), front strap bolt hole (2), under the bolt starting at the neck and moving forward (3), and round the back bolt and butt pad (4).While plastic molded rifles are definitely tougher, no rifle is indestructible. Many color guard instructors suggest taping your plastic rifles too. This little bit of extra care allows your rifle to withstand more shock without cracking.

Why do you tape a color guard rifle?

While plastic molded rifles are definitely tougher, no rifle is indestructible. Many color guard instructors suggest taping your plastic rifles too. This little bit of extra care allows your rifle to withstand more shock without cracking.

Can you paint a color guard rifle?

If the rifle is a “Premier” or “Ultimate” it is painted with lacquer and you can use both lacquer or enamel paint for repairs.

How to Tape a Color Guard Rifle

We recently received an email from a reader asking how to repaint a rifle if it gets a chip. We spoke to John from Premier Rifles for advice. He recommends that!

To be on the safe side, you should use lacquer paint on rifles. Some rifles are painted with enamel and others with varnish, depending on the manufacturer. Enamel doesn’t lift varnish, but varnish does lift enamel. If the rifle is a “Premier” or “Ultimate” then it is varnished and you can use both varnish and enamel paint for repairs. To be on the safe side, use enamel for all other rifles or contact the manufacturer.

Preparation is also important when you have chips on the rifle. Sand the rifle with 220 grit sandpaper and prime the bare wood. Primer is a matte layer that adheres to bare surfaces such as wood and fills in slight imperfections. It is also easy to grind. After priming, sand with 400 grit sandpaper and spray on your paint. Not only does it look bad if you don’t sand the chips to fuse them to the wood, the new paint can get under the old and make the old paint stand out around the chips.

Spray paint always looks nicer than a brush. Spray gives you a smoother finish. Also, remember to spray several thin coats (instead of one thick one), slightly overlapping the dry area you just sprayed. If you spray a pass over the rifle you will see the wet glossy paint and the edges will become dry and dull. Make your next pass at the top or bottom of the shiny wet area. I would recommend using Rust-Oleum brand white primer and Rust-Oleum brand gloss white paint. It doesn’t “walk” as easily as the cheaper brands.

A big thank you to John from Premier Rifles for sharing his knowledge!

Related Articles: “Protect Your Rifle”

Where do you tape a rifle?

ELECTRICAL TAPE

This little bit of extra care allows your rifle to withstand more shock without cracking. Wrap separate pieces of strapping tape all the way around the nose (1), front strap bolt hole (2), under the bolt starting at the neck and moving forward (3), and round the back bolt and butt pad (4).

Can you use electrical tape for color guard flags?

Pinch the flag at the seam and pull slightly, to make sure the flag will not be wrinkled as you tape it on. Then, take your electrical tape and go around the top of the silk only once or twice, do not overdo it.

How to Tape a Color Guard Rifle

Taping is a precaution that can prevent your flag from falling at the worst of times, like during practice or worse, during a performance. In addition to sticking the flag, you have the benefit of being able to use thirds (sometimes called “cheaters”) in our color protection. They help tell you where to place your hands! Use them to your advantage and read on to learn how we stick a paint protection flag at Rancho HS. You need to know the parts of a flag to understand where to put what, so see the picture of the labeled parts before proceeding!

Please note: I am aware that there was an error in the caption. The labels for “third” and “lower third” should be swapped. I apologize in advance.

Why do soldiers put tape on their guns?

Taping magazines together in order to speed up reloading became so common among troops using the M1 Carbine that the U.S. military experimented with the “Holder, Magazine T3-A1”, which came to be referred to by some infantrymen as the “Jungle Clip”.

How to Tape a Color Guard Rifle

Firearm magazines are used “jungle style” when attached side by side, often with tape. The spare magazine can face down compared to the one attached to the gun.

This configuration is used to speed up the reloading process, since a loaded magazine is attached to the one in use. Disadvantages include an increased risk of interruptions due to the cartridges and magazine lips being exposed to debris (especially if the second magazine is inverted), possible ammunition loss, and that the extra length of two magazines together can increase the profile of a prone soldier.

To counteract these disadvantages, some manufacturers such as SIG and Heckler & Koch[1] have developed magazines with bolts and brackets that allow additional ammunition to be carried in parallel in an upright position without the need for tape or clips.[1] High capacity Ram-Line magazines for Ruger 10/22 .22 LR semi-automatic rifles are also equipped with pins and sockets to allow them to be coupled together.

history [edit]

The practice of “jungle style” magazines originated in World War II for the M1 carbine,[2] M3 “Grease Gun”[3] and the Thompson submachine gun. Audie Murphy, one of the most decorated American combat soldiers of World War II, is said to have used glued M1 carbine magazines.[5]

Thompson submachine gun users often taped two 20-round magazines together to speed up reloading and make up for the limited capacity. This spurred the official development of the 30-round Thompson magazine, which involved the experiment of welding two 20-round magazines face to face (dropped in favor of the 30-round magazine). United Defense’s M42 submachine gun was occasionally issued with two 20-round magazines welded face-to-face.

Clipping magazines together to speed up reloading became so common among troops using the M1 carbine that the US military experimented with the “Holder, Magazine T3-A1”, dubbed by some infantrymen as the “Jungle Clip ” was designated. This metal clip holds two M1 Carbine 30-round magazines together without the need for tape.[7]

Image gallery[edit]

Why is color guard not considered a sport?

Color Guard is not considered a sport because of the naivety of people to understand the amount of physical exertion and work involved in learning and executing routines. It can also be because it lacks in popularity behind cheerleading and other dance-like sports that get more attention.

How to Tape a Color Guard Rifle

My daughter was recently talking to a friend about being in color guard, her boyfriend (we call him Max) made fun of her for calling color guard a sport. My daughter was right to defend herself. She informed Max of the amount of physical exertion and exercise required of her to be in the color watch. After sharing this conversation with myself, I thought we should end this topic once and for all!

Color guard is not officially recognized as a sport, but due to its physical exertion and competitive nature, it fits the definition of a sport. Color Guard is an activity requiring both skill and physical exertion conducted with a team competing against others for entertainment.

Unfortunately, with color guard not being as popular as other sports, it can be hard for some people like Max to believe that this is actually considered a sport. Here’s my argument to see if I can change his mind.

What makes a sport

Dictionary.com defines a sport as “an athletic activity involving skill or physical ability, often competitive,” then mentions racing, baseball, bowling, and a few others.

Wikipedia says: “Sport refers to any form of competitive physical activity or play aimed at using, maintaining or improving physical abilities and skills while providing fun for participants and, in some cases, entertainment for spectators.”

✔ Does Color Guard require skill? …… Yes!

✔ Does Color Guard require and enhance physical skills? … Yes!

✔ Does Color Guard require athleticism? ….. Yes!

✔ Is Color Guard competitive? ….. Yes!

✔ Does Color Guard provide entertainment or pleasure for an audience? ….. Yes!

✔ Can you get hurt in Color Guard? …. Yes!

Color Guard fits every aspect of the definition of a sport!

Is color guard a sport? ✔ YES!

Does Color Guard require skill?

Color Guard requires many different skills. These skills include teamwork, perseverance, proper technique, marching, musical timing and rhythm, synchronization, flexibility, and technical knowledge of how to execute various flag throws and holds.

Colorguard requires teamwork

Working together towards a common goal as a team is a hallmark of any sport. A color guard team can consist of 1 to 50 people (flags), but even if there is only 1 person, they still work together with the marching band.

Team members need to be aware of their team members’ strengths and weaknesses so they can help each other improve, they also need to work together to synchronize their movements with each other.

Color Guard requires perseverance

Although the typical halftime show in which a color guard performs lasts only 5 to 15 minutes, drills often last an hour or more.

During Bandcamp Color Guard will sometimes practice all day. The flags can be heavy and require a lot of arm and wrist strength to execute and practice the throws over and over again.

In the summer, my daughter attends band camp with her high school as a member of the color guard.

The first week runs from 8am to 5pm with a short lunch break in the middle of the day. The next week is from 8am to 9pm every day practicing drills with the marching band and practicing alone with just the color guard.

During band camp, while the marching band is sitting indoors and rehearsing, the color guard is often still on their feet practicing moves and throws.

Color Guard is a very physically demanding sport!

Color Guard requires knowledge and technique

Just like many sports, a playbook color guard has something similar that needs to be studied and understood and that is a drill chart. Knowing the jargon and understanding how to use it with the team is a big part of this sport.

To be in Color Guard you must also learn the basic flag movements and techniques. You need to know how to throw different types of tools, mainly a flag, a rifle and a saber.

Color Guard Sabers (Your Complete Guide)

All About Color Guard Flags (Full Guide)

Color Guard requires flexibility, timing and rhythm

Just like gymnastics requires flexibility, basketball and soccer are all about good timing and believe it or not, baseball requires a certain amount of rhythm, Color Guard uses ALL of those things!

Because of the dance moves in Color Guard, flexibility of the body is important. Timing flag tosses with your team is important to performing well in competitions, and a general rhythm and flow will help color guards stay in sync with the other members of their team as well as the marching band as a whole.

Color Guard requires physical ability and athleticism

A member of the color guard is often the most mobile and fastest-moving person on the marching band field. Not only do they march in step with the band, but they run, jump, jump and dance. Her contribution to the band is her movement.

In one of my daughter’s drills for her halftime show this year, she has to jump from one position in the field to almost the other side of the field in several short counts (Jazz Run). If you’re not physically fit, these short bursts of high-intensity movement, along with maintaining the physical demands for the rest of the show, can be very challenging.

Color Guard is competitive

At the high school level, fall color guards and marching band usually compete against regional bands on weekends. This often involves traveling to different schools and performing at a specific time in front of audiences and judges.

Judges will rate players on a range of skills including musicality, technical execution and synchronization. The band then gets a score and feedback on how to improve their show.

Color Guard members may also compete in the Winter Guard during the marching band’s off-season. There is a

WGI, or Winter Guard International, has held indoor color guard competitions since the 1970s.

Color Guard provides entertainment and enjoyment for an audience

Many football fans can attest that sometimes the most exciting part of the football game is the halftime show. I remember being in the Utah State University Marching Band and feeling excited and extremely nervous about performing to a huge homecoming crowd.

We’ve done some pretty amazing shows. One was a tribute to The Beatles, and one was all about Scooby doo. The shows were meticulously choreographed and definitely entertaining.

Getting the crowd going with cheers and screams was one of my favorite things about performing!

Throwing the flag and spinning it in all directions can be considered a “sport of arts”, it is so graceful that it tells a story while bringing music to life and evoking many emotions.

At my daughter’s high school, they often invite spectators to come and watch the competitions. They can even ask for a small amount of money as an entrance fee. The money will be used for the costs of the marching band.

Isn’t it typical that a sport is designed to showcase and entertain an audience for a fee to watch the game?

Can you hurt yourself in Color Guard?

Yes, it is entirely possible to get injured in Color Guard. Musculoskeletal injuries are the most common. Because the flag is heavy and requires skill to throw and catch, learning and practicing while practicing may result in bruises, broken noses, strained muscles, or other injuries. Ankle sprains are also common marching injuries.

As with any sport, you must take a calculated risk and take precautions to minimize that risk. Color Guard members often wear gloves and have very sturdy athletic shoes to support and prevent injury.

I remember early in her freshman year at Color Guard my daughter came home one day with a black and purple knee with a big cut down the middle. Apparently she had hit the end of her flag just right, causing quite a bit of injury and pain. Luckily it was only superficial and nothing too serious.

Is color guard or winter guard an Olympic sport?

Color guard is not one of the 46 different Olympic sports, however there are many people who would like to make it an Olympic sport. You can find many petitions to sign online trying to prove that color guard is a sport and should be included in the Olympics.

Artistic gymnastics is most likely the closest related sport currently featured in the Olympics.

Why is color guard not considered a sport?

Color Guard is not considered a sport as people are naïve to understand the amount of physical exertion and work involved in learning and performing routines. It may also be due to a lack of popularity behind cheerleading and other dance-like sports that are getting more attention.

Color guard just needs his chance to be in the spotlight for people to realize how exciting, powerful and difficult a sport is. Once that happens I think everyone will agree that color guard is a sport!!

What is the difference between a color guard and an honor guard?

Colors, or flags, are often carried by both, but the primary purpose of the Color Guard is to present the National Colors at a presentation or ceremony. The Honor Guard may present the Colors, but their main purpose is to present a contingent to bear honors at ceremonies or funerals.

How to Tape a Color Guard Rifle

There is a fine line between Color Guard and Honor Guard. The easiest way to tell them apart is by asking a question: Have you attended the (Wing, Region, or National) Honor Guard Academy for seven days? If the answer is no, you cannot wear the Honor Guard uniform. You can still perform some of the same tasks in the community disguised as “Color Guard”. A more official definition is as follows:

Colors or flags are often carried by both, but the color guard’s primary purpose is to present the national colors at a presentation or ceremony. The Honor Guard may present the colors, but their primary purpose is to present a contingent that renders honors at ceremonies or funerals.

The Uniform of the Honor Guard

The Honor Guard uniform is similar to that of the United State Air Force Honor Guard, but with differences. The shoulder cord doesn’t have the same style, just the color. The silver stripe is not worn on the sleeve, trousers, or trousers, nor does the service hat have a silver-trimmed beak or chin strap. The Air Force Honor Guard ceremonial belt is not worn, instead a white pistol belt with nickel fittings. The patch on the ascot is a different shape and color.

What do I have to do?

The minimum requirements for participation in the Honor Guard are:

service coat

A duty jacket can be purchased at full price in person with your CAPID at any AFB uniform store (exchange), ie. H. Andrews AFB, MD or Bolling AFB in DC or Langley AFB in Hampton Roads, VA. For the patient, you may be able to purchase duty coats free of charge from AFB thrift stores or from our squadron inventory (derived from thrift store shopping sprees by squadron members looking for cadet-sized USAF uniforms). Some parents are also able to successfully buy gently used, more affordable duty coats online from stores like ebay.

Wheel cover (with back strap & CAP device)

CAP hubcaps are rarely found at thrift stores and most often must be purchased either through Vanguard or in person at the aforementioned AFB uniform stores for $50. Rear chin strap and hubcap CAP devices by Vanguard.

Wheel Cover Cap – Civil Air Patrol Company Grade Service Cap – Male (For Male and Female HG Cadets) $65 at Vanguard – but only $40.00 at the Exchange

Civil Air Patrol Uniform: Company Grade Service Cap – male

Cap Strap: Black Buckle Back $11

http://www.vanguardmil.com/cap-strap-black-back-with-buckle-p-15788.html

Civilian Air Patrol Cap Apparatus – Cadet Officer, Male (Both Male and Female) $8

Civil Air Patrol Cap Device: Cadet Officer Service – male

Additional items to borrow or invest:

The squadron currently holds the remaining items to outfit six Honor Guards at each event. The media listed below are available for loan on a rotation of currently eligible members.

Note: It helps program and maximum member participation if a cadet can personally own/purchase these items to be available for performances that require more than six members.

White Bib Scarf (Ascot) $11.90

http://www.vanguardmil.com/bib-scarf-white-p-2722.html

Honor Guard Patch (sewn onto bib/ascot) $2.25

http://www.vanguardmil.com/civil-air-patrol-patch-honor-guard-p-14005.html

Belt & Buckle – Parade (Gun Belt) $42 Available on Vanguard but – don’t order from Vanguard! See Commander of the Honor Guard. This item is ordered through Parade Magazine.

Gloves & Silver Shoulder Cord (These are also available through Vanguard but see Honor Guard Cadet Commander for ordering instructions. These items come with recommendations and depending on the style of service coat an alternate source may be required.)

What is the difference between color guard and winter guard?

Winter Program

Winter guard is an indoor color guard activity derived from military ceremonies or veterans organizations ceremonies. Unlike traditional color guard, winter guard is performed indoors, usually in a gymnasium or an indoor arena.

How to Tape a Color Guard Rifle

Emory & Henry Color Guard Mission Statement

We work together to represent spirit and pride for our college. We are dedicated to advancing the marching arts, performing arts and music education for all. We express our determination, hard work, self-respect, discipline and perseverance through progress towards team goals. Our passion for Color Guard stems from the fun we have, the friendships we make and the sense of accomplishment we get in the end.

Interested in joining the Color Guard/Winter Guard?

Color protection and winter protection application

Date of the next information event:

Sunday, October 31 at 3:30 p.m. in the Marching Band Building at Emory & Henry College

Email [email protected] to RSVP to participate.

autumn program

The Color Guard at Emory & Henry College is part of the Marching Band and Music program. This unit consists of marching band members who add visual impact and color to the musical performance in a challenging activity that combines equipment work with dancing and marching.

winter program

Winter Guard is an indoor color guard activity derived from military or veteran organization ceremonies. Unlike traditional color protection, winter protection is performed indoors, typically in a gym or indoor arena. Auditions for the winter program are held in late fall and are open to anyone who was a member of the E&H Marching Band in the fall semester prior to the winter season.

During the winter program, the guard continues to master their gear skills and learn a higher vocabulary of choreography. The Winter Guard focuses more on dance and movement skills that are built into the routine to challenge the group and take them to the next level of precision and dexterity.

How to Properly Tape an Elite Color Guard Rifle (learn from DSI how a pre-taped rifle is created)

How to Properly Tape an Elite Color Guard Rifle (learn from DSI how a pre-taped rifle is created)
How to Properly Tape an Elite Color Guard Rifle (learn from DSI how a pre-taped rifle is created)


See some more details on the topic how to tape a color guard rifle here:

Taping Your Color Guard Rifle – Band Shoppe

Referencing the diagram above, wrap the electrical tape continuously around the rifle starting at the neck and moving forward to a couple inches …

+ Read More Here

Source: blog.bandshoppe.com

Date Published: 5/10/2022

View: 8271

How to tape a rifle – How to color guard – Spintronix

Starting in the neck, wrap the electrical tape around the rifle and travel forward, making sure that each wrap of the tape slightly overlaps the …

+ Read More Here

Source: www.spintronixguard.org

Date Published: 3/28/2022

View: 2112

How to Pad and Tape a Color Guard Rifle – Condo Blues

Start three finger lengths from the neck of the rifle and continue taping with one continuous piece of strapping tape (as possible) until you …

+ Read More

Source: www.condoblues.com

Date Published: 12/26/2021

View: 8674

Protecting Your Rifle! – Color Guard Educator

If you d not receive a taping diagram with your rifle, the instructions here are pretty universal and should protect most rifles. Add strapping tape at the …

+ View More Here

Source: colorguardeducator.com

Date Published: 9/28/2022

View: 9787

Taping Your Color Guard Rifle

Maybe you just got a nice brand new rifle or maybe it’s the start of a new season – Band Shoppe can help you keep it from breaking the first time it hits the ground.

Photo courtesy of Boston Crusaders

Wooden guns require gluing to reinforce inherently weak areas. While guns molded from plastic are definitely sturdier, no gun is indestructible. Many color protection teachers suggest putting tape on your plastic guns as well. This little extra care allows your rifle to withstand more impact without breaking.

Remember that there are many ways to glue a rifle, this is just a basic method. You can also mask off the entire rifle, bolt, or sling with tape to give it a different color! Some people use glitter tape or glow in the dark tape to create different effects.

The most important accessory you need to tape your rifle is strapping. Strapping tape has nylon threads for extra support. You can find it at bandshoppe.com for less than $5.00 a roll. Band Shoppe also suggests electrical tape to tape over the strapping. Electrical tape has a little stretch that helps the tape stick more firmly, it’s economical at about $2.00 a roll, and comes in a range of colors. Professional quality gaffer tape like our Deluxe Rifle Tape also works very well. It’s your decision!

Start with a clean gun, free of old tape and glue residue. Wipe your rifle with a clean, soft cloth to remove skin oils. This will help the new tape stick better.

Ready to start? Big! Gather your supplies first.

You will need the following:

1 Phillips screwdriver (the one with the + shaped tip)

Nylon Strap (Item #64324)

White Electrical Tape (Item #64320)

Electrical tape that fits your harness

Using a Phillips head screwdriver, remove all of the rifle parts, including the two screws holding the bolt in place and the two screws holding the strap in place. If your rifle has rubber butt pads, like the Endura rifle, you can go ahead and leave them in place.

STRAP

Wrap individual pieces of tape all the way around the nose (1), the front strap bolt hole (2), under the bolt starting at the neck and forward (3), and around the rear bolt and stock pad (4).

ELECTRICAL TAPE

Referring to the diagram above, wrap the electrical tape continuously around the rifle, starting at the neck and working forward to a few inches behind the bolt. * Make sure the tape slightly overlaps each turn. Secure your clips and o-rings with the screws provided, then wrap the tape around the area above the front screw a few turns. This will prevent the screw from loosening or scratching you as you turn it. Next, place a few strips of duct tape parallel across the rifle butt from top to bottom long ways. Repeat this step on the rifle nose using shorter strips of tape to hold the pads in place and protect the ends from additional wear. Continuously wrap towards the nose and over the strips of tape from step 3, repeat on the butt of the rifle, making sure to wrap the rear bolt. Attach the gun sling to the O-rings. Wrap electrical tape that matches the color of your belt three times around points A and B to ensure the belt bolts do not come loose.

ATTACH YOUR BOLT AND THAT’S IT!

Share this: Twitter

Facebook

Taping Your Color Guard Rifle

Maybe you just got a nice brand new rifle or maybe it’s the start of a new season – Band Shoppe can help you keep it from breaking the first time it hits the ground.

Photo courtesy of Boston Crusaders

Wooden guns require gluing to reinforce inherently weak areas. While guns molded from plastic are definitely sturdier, no gun is indestructible. Many color protection teachers suggest putting tape on your plastic guns as well. This little extra care allows your rifle to withstand more impact without breaking.

Remember that there are many ways to glue a rifle, this is just a basic method. You can also mask off the entire rifle, bolt, or sling with tape to give it a different color! Some people use glitter tape or glow in the dark tape to create different effects.

The most important accessory you need to tape your rifle is strapping. Strapping tape has nylon threads for extra support. You can find it at bandshoppe.com for less than $5.00 a roll. Band Shoppe also suggests electrical tape to tape over the strapping. Electrical tape has a little stretch that helps the tape stick more firmly, it’s economical at about $2.00 a roll, and comes in a range of colors. Professional quality gaffer tape like our Deluxe Rifle Tape also works very well. It’s your decision!

Start with a clean gun, free of old tape and glue residue. Wipe your rifle with a clean, soft cloth to remove skin oils. This will help the new tape stick better.

Ready to start? Big! Gather your supplies first.

You will need the following:

1 Phillips screwdriver (the one with the + shaped tip)

Nylon Strap (Item #64324)

White Electrical Tape (Item #64320)

Electrical tape that fits your harness

Using a Phillips head screwdriver, remove all of the rifle parts, including the two screws holding the bolt in place and the two screws holding the strap in place. If your rifle has rubber butt pads, like the Endura rifle, you can go ahead and leave them in place.

STRAP

Wrap individual pieces of tape all the way around the nose (1), the front strap bolt hole (2), under the bolt starting at the neck and forward (3), and around the rear bolt and stock pad (4).

ELECTRICAL TAPE

Referring to the diagram above, wrap the electrical tape continuously around the rifle, starting at the neck and working forward to a few inches behind the bolt. * Make sure the tape slightly overlaps each turn. Secure your clips and o-rings with the screws provided, then wrap the tape around the area above the front screw a few turns. This will prevent the screw from loosening or scratching you as you turn it. Next, place a few strips of duct tape parallel across the rifle butt from top to bottom long ways. Repeat this step on the rifle nose using shorter strips of tape to hold the pads in place and protect the ends from additional wear. Continuously wrap towards the nose and over the strips of tape from step 3, repeat on the butt of the rifle, making sure to wrap the rear bolt. Attach the gun sling to the O-rings. Wrap electrical tape that matches the color of your belt three times around points A and B to ensure the belt bolts do not come loose.

ATTACH YOUR BOLT AND THAT’S IT!

Share this: Twitter

Facebook

How to Tape a Color Guard Rifle

You’ll need to glue these as well, as you don’t want your strap to come loose when you need it most. I cannot stress enough how important it is to do this. I once borrowed a rifle with no tape covering those flat head screws for a trial. It fell apart when I did a strap toss and the rifle hit my head, ouch! Not something you want to happen to you.

Related searches to how to tape a color guard rifle

Information related to the topic how to tape a color guard rifle

Here are the search results of the thread how to tape a color guard rifle from Bing. You can read more if you want.


You have just come across an article on the topic how to tape a color guard rifle. If you found this article useful, please share it. Thank you very much.

Leave a Comment