Pal 2000 Pool Light Installation? All Answers

Are your pool lights not working?

If you have a swimming pool in your garden or on your property, you probably have lighting installed in it as well. Swimming pool lighting can add a lot of beauty to your pool along with the ability to safely use and enjoy it 24/7. However, after a while, you may find that your light flickers or won’t turn on. While you may think it’s time to drain your pool and replace the lightbulb, which can be an extremely tedious and expensive process, you may be surprised to learn that you may just have another factor in your electrical system need repairing. The trick is to troubleshoot a few things to figure out what the problem is before removing the water from your pool.

Easy pool light troubleshooting

The first thing you should do is put on your swimming goggles and go underwater to check the light yourself. Try to see if you can shake the ring holding the light fixture into the pool itself. If it moves slightly when you touch it or move water past it, try plunging a larger Phillips screwdriver back down to tighten it.

Put on your swimming goggles and head underwater to check out the light for yourself. Try to see if you can shake the ring holding the light fixture into the pool itself. If it moves slightly when you touch it or move water past it, try plunging a larger Phillips screwdriver back down to tighten it. If that doesn’t work, try checking your light fixture to see if you can spot water in it. If there is water in the faucet itself, you may have a leak. This is usually due to a bad lens gasket, which is a rubber seal between the lens and the body. However, this can also be due to the fact that the pipe seal wears out over time. Unfortunately, fixing any of these issues requires draining the pool.

, try checking your fixture to see if you can spot water in it. If there is water in the faucet itself, you may have a leak. This is usually due to a bad lens gasket, which is a rubber seal between the lens and the body. However, this can also be due to the fact that the pipe seal wears out over time. Unfortunately, fixing any of these issues requires draining the pool. If you finally fix the fixture and the light didn’t turn on, your bulb may have burned out. Remove the bulb from the holder and shake it near your ear. If you hear the filament run into the sides of the bulb, your bulb is dead and needs to be replaced.

More difficult troubleshooting

If replacing your lightbulb doesn’t work and you’ve made sure all of your gaskets are in good condition, you may have tripped the circuit breaker. Generally, this happens when you plug in or turn on a new device into an outlet that is on the same circuit as your pool lights. Check the circuit breaker panel, which is usually located on the side of your home. If your pool light breaker has tripped, unplug everything you just turned on or plugged in and reset the breaker by turning it all the way off and then back on.

If that doesn’t work, you may have a bad breaker. If this is the case, it is highly recommended that you call a Marietta electrician to have it replaced.

Finally, there’s another possible option: you’ve tripped your RCD. Better known as GFCI, this is a device used to reduce the hazard in installations that have a higher than usual risk of electrocution. They are usually found on electrical outlets in bathrooms and kitchens, and you can usually find them outdoors as well. If you have GFCI sockets on your pool lighting circuit, try resetting them. If that doesn’t work, you may need to replace it.

At Lighting Bug Electric we offer a range of pool lighting services in Marietta and Atlanta. If you have problems with your pool lighting, contact our experienced and competent team. We work quickly and efficiently to diagnose the problem and provide permanent solutions. In addition, we offer competitive prices for every budget.

If you need help with an electrical problem, Lightning Bug Electric can provide you with quality service! Call us today at (404) 471-3847 to schedule an appointment.

Sure, swimming during the day is fun. There’s nothing quite like taking a dip on a hot day and watching the pool sparkle in the sunlight. But there is also a lot to be said for night swimming. The water is often warmer than the cool evening air, sunburn is a thing of the past, and you can float on your back and gaze up at the stars. Nice.

However, swimming in a pool at night without lights isn’t nearly as fun. Who knows what kinds of deep-water monsters lurk beneath the surface, unseen and waiting? Even just a pool light bulb going out can result in a less than comfortable swim. The good thing is it’s easy to fix.

Replacing and upgrading a pool light bulb

Replacing a blown pool light bulb is a fairly simple task. Note, however, that your lightbulbs don’t have to be out for you to replace them.

You can also upgrade to brighter, more energy-efficient LED bulbs that use a fraction of the energy of traditional incandescent bulbs. Many LED bulbs can also change color, adding more fun to your evening pool parties and late-night swims.

When you go pro

Replacing a pool light bulb sounds easy, and it is. But it’s important to remember that this is not like changing the light bulb in a lamp. You have the added risk of submerging the bulb in water. And to change it, you will probably also be in the water. And we don’t have to explain how electricity and water don’t mix, do we?

So if you are in any way uncomfortable with this task, hire a professional. Safety is always a top priority, and a pool attendant can quickly and easily replace a pool light bulb – or all of them if you’re upgrading.

Frustrated with adding chemicals and trying to keep your pool clean all the time? We’ve taken all the confusion out of pool maintenance in this easy-to-read, illustrated e-book and video course. It will help you save $100 on pool maintenance instantly! Click here to learn more

If you do DIY

Are you up for the challenge of replacing a pool light bulb yourself? That is why we are here! First determine what type of light bulb is compatible with your pool, then make sure you have the right accessories on hand.

You need:

Replacement pool bulb

replacement lens seal

Phillips and slotted screwdrivers

multimeter

Dry towels (a few)

Ch-ch-ch-Changin’ That Pool Light

Because safety always comes first, be sure to read all instructions before you begin and do not skip any steps.

1. Turn off the device

Keep in mind that when changing a pool light bulb, you will be touching wires and will likely be standing in water, or at least touching it. Before doing anything with your pool lights, check and then check twice and then thrice to make sure no electricity is reaching your pool area.

1a. Drain some water from the pool

This step is optional. If you can reach the light more easily and work on it, be sure to drain some water beforehand. Just remember that afterward you will need to replace it and add chemicals to rebalance the water.

2. Remove the guide screw from the light

It is most commonly found at the top of the light. Screw types vary, so you will need either a flathead or Phillips screwdriver.

Magnetic Screwdriver Set – 14 Piece $20.39 Buy Now If you click through this link and make a purchase we will earn a commission at no additional cost to you.

3. Pry out the bracket

Once the screw is removed, gently pry the light out of its bracket. In most cases you will find that you have plenty of extra wire to be able to remove the bracket from the pool and place it on the deck. Put it on one of the towels to avoid scratching the lens.

4. Test the wiring

Before touching the wires with your bare hands, use the multimeter to be absolutely sure that no current is flowing through them.

If so, something hasn’t been turned off, so find it and turn it off before proceeding.

5. Disassemble the bracket

Remove any screws or clamps holding the mount together and pull apart the lens, lens gasket, and face ring so you can access the pool light bulb.

It’s possible that some or all of these parts have corroded over time, so use caution when disassembling them and be careful not to do so over water to avoid debris falling in.

Wipe off dirt or other debris with a dry cloth. If the corrosion is severe enough to prevent installing a new bulb, you may need to replace the entire assembly.

6. Remove the old lightbulb

Use a towel to grab the bulb and slowly and carefully unscrew it. If it’s outside, use a towel to dry and clean the inside of the light.

7. Add the new lightbulb

Slowly and carefully screw in the replacement pool light. Make sure it’s snug, but be careful not to over-tighten. You risk breaking it that way. Install the lens gasket around the lens, and then reassemble the mount.

8. Test the light

Before replacing the bracket in the pool wall, turn on the power and make sure the light is on.

Important: Do this quickly as pool lights are not designed to function out of the water for very long.

More importantly, once you’ve verified the light is working, turn the power back off to complete the installation.

9. Check for leaks

Submerge the lamp and ensure that no air escapes from the sealed outer edges of the lamp. If you see air bubbles, remove the unit from the water and repeat the process of disassembly, internal drying and reassembly.

Then test it again until you see no more air bubbles.

10. Replace the light in the pool wall

Push the excess wiring back into the wall, then carefully slide the bracket back into place. Make sure the screw holes in the bracket match those in the wall, then replace the screw(s).

11. Turn the device back on

Check one last time that the light is on. If that’s the case, pat yourself on the back and go for a celebratory swim!

Important: Just a reminder that if this sounds like you to you, you might as well stick a fork into an outlet. Don’t hesitate to hire a professional to do the job for you.

Pools brighten your life

Now you can invite friends over to enjoy the evening pool atmosphere, or just swim in the moonlight whenever you like. If you’ve installed an LED light that changes colors, have a little fun pretending you’re floating on another planet or in a futuristic sci-fi movie.

The great thing is, once you’ve replaced a pool light bulb, it’s even easier to do so the next time one of them burns out. And you can add another award to your DIY resume.

Have fun swimming!

Matt Giovanisci is the founder of Swim University® and has been in the pool and spa industry since 1995. Since then, his mission has been to make pool and hot tub maintenance easy for everyone. And every year he helps more people with water chemistry, cleaning and troubleshooting.

Download our FREE pool maintenance cheat sheet. This free printable cheat sheet will help you keep your in-ground, above-ground, or Intex pool clean and clear without messing with confusing water chemistry. Get the FREE cheat sheet

PAL 2000 underwater lighting for pools and spas. LED pool lighting suitable for concrete and fiberglass pools.

The NEW PAL Touch LED Pool Light gives you ultimate control over the colors of your pool lights. Touch lights complement most pools and spas, bringing a unique blend of color, functionality and control to your entertainment space.

Benefits of PAL pool lighting

Unique prismatic light distribution

Compact size

Fits flush to the wall

Prismatic light distribution

Unique side light function

easy installation

24 m cable available

Replacement parts are available for the PAL2000 halogen lights.

How to install PAL Pool Lights

The lights of the PAL2000 LED series offer a unique light extraction system that gives you a comfortable, even light distribution at all times. Use these lights in your concrete or fiberglass pool.

The PAL 2000’s unique flush mounting method eliminates unsightly and unsafe protrusions on the pool’s smooth interior surface, and the light’s ultra-safe low wattage rating coupled with the specially designed double-insulated transformer allows for a continuous power supply – up to 24 meters without unsightly junction boxes in the pool Deck to use around the pool.

Edited by Writer

Installing lights in and around your pool is a great way to add ambience and ensure you can swim day or night. While Columbia, SC pool lights can last for years before burning out or even needing a detailed pool light repair, they’re not invincible.

One of the most common questions we get when it comes to pool lights is whether the water needs to be drained before replacing a burned out bulb. After all, the last thing you want is water flowing down the electrical line after you remove the fitting.

Luckily, the answer is no – the water doesn’t usually need to be drained! Because the electrical cord is sealed, it is impervious to water entering the line when replacing the bulb.

When may you need to drain the pool?

It is important to note that in some situations a drain may be required. If your pool is on a hill and the electrical equipment is under the pool, you will need to drain the water before replacing your pool lights in Columbia, SC. Skipping this step will wash away all your electrical work, resulting in a hefty repair bill.

If you’re unsure whether you should drain the water before replacing a lightbulb, just ask a pro! A pool specialist can confidently tell you if the water needs to be drained or if you can go ahead with a full pool.

Why hire a professional to change your lights?

With the right tools and a little extra weekend time, you can replace a pool light yourself. However, we do not recommend it. Here are some reasons to hire a professional for your Columbia, SC pool light replacement:

Guaranteed Results: Replacing a pool light isn’t the hardest thing in the world, but it’s not entirely foolproof either. If you buy the wrong replacement bulb or fail to secure the fixture after replacing the bulb, you will have to go to the store again and do the job again. Pool technicians know exactly what they are doing and get the job right the first time.

Replacing a pool light isn’t the most difficult thing in the world, but it’s not entirely foolproof either. If you buy the wrong replacement bulb or fail to secure the fixture after replacing the bulb, you will have to go to the store again and do the job again. Pool technicians know exactly what they are doing and get the job right the first time. Safety Concerns: There is always a risk of electrocution when working with electrical components. A small mistake can result in a serious injury. Pool technicians are trained and certified to work with a pool’s electrical systems, making them much safer than the average homeowner.

There is a risk of electric shock when working on electrical components. A small mistake can result in a serious injury. Pool technicians are trained and certified to work with a pool’s electrical systems, making them much safer than the average homeowner. SAVE TIME: Your time is your most valuable asset, so why waste it replacing your pool lights? Instead, sit back and relax while the pros get to work. With years of experience, they get the job done in no time.

Speak to the Can Do Cast crew today

Spring is just around the corner, which means it’s time to get your pool ready for the season! Be sure to hire the Can Do Plaster Crew as part of your seasonal pool prep. From small touch-ups to pool light repairs in Columbia, SC, we are the full-service team for all of your pool needs. Call us today for a free estimate.

Categorized in: Pool Renewal

This post was written by Writer

I wasn’t sure what to do but after reading this article I feel better knowing it’s an easy procedure to fix.”

…”

“I’m a first time pool owner and I’m still learning about the whole process of the pool. When it comes to water and electrics,

You can be electrocuted by a pool light in a swimming pool. It can cause serious injury and even death. An experienced electrocution attorney can help victims and families recover damages for personal injury or wrongful death to which they are entitled by law.

How can you get electrocuted by a pool light?

You can be electrocuted by a pool light if faulty wiring or a defective lighting fixture causes an electrical current to be released into the water and you come into contact with the electrified water.

What happens if you get electrocuted by a pool light?

Death or severe injuries can result. It is possible for a person to die instantly or be electrocuted in the water if the electric current paralyzes a person and causes them to drown.

Can you claim compensation for pain and suffering?

You may be able to recover pain and suffering damages from any responsible party if you or a loved one has suffered an electric shock injury.

Can I claim damages from unlawful homicide?

If a family member or loved one loses their life after being electrocuted by a pool light, your family may be entitled to wrongful death damages from any responsible party for the pain and suffering of your loved one, for the loss of your companionship and camaraderie Reclaim family and for funeral expenses.

Who are responsible if you get electrocuted by a pool light?

There may be several responsible parties, such as the pool owner or maintenance company that you would sue in a court of law for pain and suffering, economic loss, or wrongful death damages.

Parties who may be responsible if you or a loved one are injured or lose their life depend on where the pool is located, who owns it, and who is responsible for installing and maintaining its electrical equipment and wiring.

These parties may include:

The owner of a hotel pool

The owner of an apartment complex pool

The owner of a community pool

The owner of a gym pool

The school pool owner

The owner of a garden pool

The owner of an enclosed pool at someone’s home

The company responsible for maintaining the pool

The company that installed the electrical equipment of the pool

The manufacturer of the electrical equipment of the pool

The company that inspected and determined the pool complied with the regulations

The electrician and/or electrical contractor and/or licensed electrician who performed the electrical work on the pool

What compensation is available?

The compensation you may be able to claim for damages and/or wrongful death depends on: (1) the injuries sustained; (2) whether a family member or loved one was killed; (3) current and future medical needs; (4) incapacity for work; (5) income before electrocution; and (6) your electrocution attorney’s experience, track record, and reputation.

Your choice of lawyer can have a significant impact on the amount of compensation you can claim back. Insurance companies keep track and know which lawyers are going to court and winning – and which are avoiding the courtroom and “quickly settling cases”.

Lawyers who have a reputation for going to court can settle cases for more money and often much faster.

causes

You can be electrocuted by a pool light as a result of: (1) faulty electrical wiring; (2) defective lighting equipment; (3) negligently maintained lighting equipment; (4) defective lighting equipment; (5) lack of GFCI (Ground-Fault Circuit-Interrupters) protection; (6) Lighting equipment that does not comply with applicable city and state safety codes, including the National Electric Code.

danger sign

When swimming in a lighted pool, be aware of the following danger signs: (1) a tingling sensation, muscle spasms, and/or an inability to move when near a light; (2) swimmers panic and quickly move away from a pool light; and (3) pool lights flicker or operate intermittently.

How to help when someone is electrocuted by a pool light

Here are the security measures you can take:

DO NOT ENTER THE WATER to help someone in need

Immediately turn off/disconnect all power to the pool lights and the surrounding area

Extend a carbon fiber pole (such as a fiberglass shepherd’s crook/lifehook – which are not conductors) towards the person in the water to grab or entangle the person’s body and pull (face up) in safety

Get out of the water, but DO NOT USE METAL CONDUCTORS OR ANYTHING THAT MIGHT CONDUCT ELECTRICITY

Get help from an experienced electrocution attorney

If you or someone you love has been the victim of serious injury or death from electrocution, you can call and speak to Jeff Feldman, perhaps the most experienced electrocution attorney in the country. Jeff has served cases involving low hanging power lines and against state utilities across the country. You can call toll-free at (800) 548-0043 for a free consultation.

LED BULB DISCUSSION – As mentioned above, a limited number of fixtures can be converted to LED lighting simply by replacing the bulb. The fixture must be large enough to hold the LED bulb and the old bulb must have an Edison base – like a standard household bulb. An LED light is very inexpensive. Most use less than 45 watts compared to the 300-500 watts of old incandescent bulbs – a saving of up to 85%. The LED color changing bulbs produce from 5-7 separate colors that can be mixed and programmed to create a range of automated color sequences. They are also available in white light only for customers where local regulations require white light – mainly commercial pools. In terms of brightness, the LED lamps produce a light, depending on the colour, that corresponds to a 300 to 400 watt incandescent lamp. White and yellow light generally corresponds to a 400W light bulb; The dimmer blue and red lights are equivalent to a 300W incandescent bulb. These lamps are available with both 12V and 120V. Both options produce the same brightness. The remainder of this guide covers the specific LED bulbs currently available and shows which bulbs are compatible. Once you’ve chosen your bulb, head over to our guide on how to convert your pool light to an LED color changing light.

Blown pool bulb?

How to change an underwater lightbulb:

1. Turn off power at the circuit breaker and all other switches as well.

2. There is no need to lower the water level. In almost all lights there is enough cable coiled up in the light niche so that the light can be taken to the end stone for repairs. Remove the single stainless steel screw at the top of the light (at 12 o’clock). Once removed, use a flathead screwdriver to pry the bracket out of the niche. Most lights have a tab at the bottom (at 6 o’clock) that fits into a slot on the niche or light body. You may have to pry and wiggle the lamp to release the tab and remove the bracket once the screw is removed. After removing above water, lift it onto the pool deck.

3. To get inside the bracket, use quality tools of the right size not to damage any of the soft metal screws, bolts, etc. On very old mounts, screws can easily break or become corroded from years of water and chemical exposure. Older model lights have 8 brass screws around the bracket that tighten on the tabs. Newer models have a clamp band with just a bolt or bolt/nut. Use a #2 or #3 Phillips screwdriver to remove the screws and, for clamp straps, use a 5/16 inch socket wrench. After the clamp or screws loosen, remove the light hood or light ring. Next, use a small flat head screwdriver to gently pry the glass lens out of the front of the bracket.

4. After removing the lens, remove the bulb. Most unscrew counter-clockwise. Some spa lights or small halogen pool lights have small bulbs that you push in and then turn counterclockwise a quarter turn to remove. Regardless of the type, be careful when removing the bulb, old bulbs can crack at the base when removed. It is a good idea to cover the bulb with a soft cloth before rotating to avoid injury. After removing the bulb, use the cloth to wipe clean and dry all interior surfaces. Wrap the new bulb or LED bulb in a soft cloth, both for safety and to keep finger grease off the bulb. Thread the new bulb, made specifically for the light, and pull it into the base until it stops.

5. Before reassembling the lamp, turn the lamp so you can see the bulb and turn on the power very briefly (for 1-2 seconds) to check if the bulb/lamp is working. Locate the printed instructions on the lens for proper alignment of the lens on the mount. Place the lens back on the mount using a NEW lens gasket. This is the rubber gasket around the lens, about 8 inches in diameter. The gasket only fits around the lens, it doesn’t wrap around the bezel or light ring, and no lubricant is required. Complete the assembly of the mount by clamping the bezel over the lens using the light weight screws or clamp strap. Screws should be tightened in a pattern to ensure even tightening.

6. Place the light under water and check for air leaks (a few bubbles may detach from the mounting ring). If no bubbles come out of your gasket, you have made a good seal.

7. Leaning far over the edge of the basin, reinsert the fitting into the niche. First wrap the cable around the back of the mount, then locate the bottom tab (on the mount) and the tab receiver (in the niche). Align and place the tab in position and press the bracket flush into the niche. Then it’s just the “not always easy” task of getting the pool light screw back through the light surround ring and into the threaded hole in the niche. A mask or glasses can help to see. Just tighten the screw firmly (not too tight) and then test your light again.

Replacing the pool lights for your in-ground pool does not require draining the pool or hiring a professional. The design of the pool light housing allows you to remove it from the pool without having to disconnect any cables. You could get wet replacing a burned out in-ground pool light, but by following a few safety steps you can safely replace pool lights without fear of electrocution.

Blown pool bulb?

How to change an underwater lightbulb:

1. Turn off power at the circuit breaker and all other switches as well.

2. There is no need to lower the water level. In almost all lights there is enough cable coiled up in the light niche so that the light can be taken to the end stone for repairs. Remove the single stainless steel screw at the top of the light (at 12 o’clock). Once removed, use a flathead screwdriver to pry the bracket out of the niche. Most lights have a tab at the bottom (at 6 o’clock) that fits into a slot on the niche or light body. You may have to pry and wiggle the lamp to release the tab and remove the bracket once the screw is removed. After removing above water, lift it onto the pool deck.

3. To get inside the bracket, use quality tools of the right size not to damage any of the soft metal screws, bolts, etc. On very old mounts, screws can easily break or become corroded from years of water and chemical exposure. Older model lights have 8 brass screws around the bracket that tighten on the tabs. Newer models have a clamp band with just a bolt or bolt/nut. Use a #2 or #3 Phillips screwdriver to remove the screws and, for clamp straps, use a 5/16 inch socket wrench. After the clamp or screws loosen, remove the light hood or light ring. Next, use a small flat head screwdriver to gently pry the glass lens out of the front of the bracket.

4. After removing the lens, remove the bulb. Most unscrew counter-clockwise. Some spa lights or small halogen pool lights have small bulbs that you push in and then turn counterclockwise a quarter turn to remove. Regardless of the type, be careful when removing the bulb, old bulbs can crack at the base when removed. It is a good idea to cover the bulb with a soft cloth before rotating to avoid injury. After removing the bulb, use the cloth to wipe clean and dry all interior surfaces. Wrap the new bulb or LED bulb in a soft cloth, both for safety and to keep finger grease off the bulb. Thread the new bulb, made specifically for the light, and pull it into the base until it stops.

5. Before reassembling the lamp, turn the lamp so you can see the bulb and turn on the power very briefly (for 1-2 seconds) to check if the bulb/lamp is working. Locate the printed instructions on the lens for proper alignment of the lens on the mount. Place the lens back on the mount using a NEW lens gasket. This is the rubber gasket around the lens, about 8 inches in diameter. The gasket only fits around the lens, it doesn’t wrap around the bezel or light ring, and no lubricant is required. Complete the assembly of the mount by clamping the bezel over the lens using the light weight screws or clamp strap. Screws should be tightened in a pattern to ensure even tightening.

6. Place the light under water and check for air leaks (a few bubbles may detach from the mounting ring). If no bubbles come out of your gasket, you have made a good seal.

7. Leaning far over the edge of the basin, reinsert the fitting into the niche. First wrap the cable around the back of the mount, then locate the bottom tab (on the mount) and the tab receiver (in the niche). Align and place the tab in position and press the bracket flush into the niche. Then it’s just the “not always easy” task of getting the pool light screw back through the light surround ring and into the threaded hole in the niche. A mask or glasses can help to see. Just tighten the screw firmly (not too tight) and then test your light again.