Spray Glue For Foam? The 127 Detailed Answer

Using the right glue for Styrofoam makes creating craft and hobby projects easier. The wrong glue on Styrofoam will not only create a poor bond, but some glues can even melt or dissolve this delicate material. A good styrofoam glue is safe to use on styrofoam, but it should do more than just make your project stick together. The top options are easy to apply, smell nice, and dry to an attractive finish. In addition, the best adhesives for Styrofoam ensure a better bond.

Hobby Styrofoam is a polystyrene foam that is made of plastic and contains air to make it light. While the two terms are often used interchangeably (including in this guide), most materials referred to as “Styrofoam” are solid polystyrene foam. “Styrofoam” is a trademark of polystyrene typically found in commercial settings. Many foam adhesives can work with either type.

Types of glue for styrofoam

Although several types of glue can be used on Styrofoam, the best products share the same characteristics. They are relatively uncomplicated and produce a clear finish with minimal fumes and odor. Multipurpose adhesives are useful for other materials, including cardboard, wood, glass, or metal. When purchasing styrofoam glue, remember that styrofoam is a plastic, which means any glue that contains solvents like acetone can cause it to dissolve.

craft glue

For simple craft projects at home, basic craft glue is usually more than enough. It is the most accessible and affordable option. Use craft glue to glue styrofoam to styrofoam, as well as to glue other common craft materials like cardboard, construction paper, and wood.

However, craft glue may not provide the strongest bond compared to a multipurpose glue or styrofoam glue, but is a good option for casual projects. A tackier, thicker white craft glue (quick-drying “tacky glue”) can help reduce sagging and mess when working with Styrofoam.

spray glue

Aerosol glues, available at many hardware or craft stores, are typically made for multi-purpose use around the home. Use them when gluing a variety of materials, including Styrofoam.

Spray adhesive covers a flat piece of Styrofoam much faster than glue from a squeeze bottle. However, spray adhesives are often less tacky than some adhesives (partially because they apply a thinner layer of adhesive). Spray adhesives are better suited for gluing large areas together, e.g. B. two styrofoam plates than for gluing two smaller points such. B. two styrofoam balls.

Low temperature glue gun

Glue guns are attractive because they can be used to glue a range of materials including paper, cardboard, fabric and wood; However, hot glue can damage styrofoam. Styrofoam has a low melting point, so take extra care when working with styrofoam and heat.

Use a low temperature glue gun to avoid damaging the styrofoam with heat. The lower the temperature, the better. If possible, apply the hot glue to the other heat-resistant material first and wait for the glue to cool slightly before attaching the styrofoam piece.

styrofoam

Serious hobbyists may want to use a special styrofoam glue called styrofoam glue, which is specifically designed to glue styrofoam. Styrofoam glue may be difficult to find, but it’s reasonably affordable. Those who frequently work with styrofoam, such as B. Craftsmen building styrofoam models may find it a reliable and effective choice.

Styrofoam glue is available at some hardware or craft stores. Some styrofoam glues are just for styrofoam (to glue styrofoam to styrofoam), while others are multi-purpose glues.

What to consider when choosing the best glue for styrofoam

Manufacturers make different types of glue for Styrofoam, but the best product depends on the needs and personal preferences of the craftsman. When deciding which polystyrene adhesive product to use in a project, consider the intended use, tack time, drying time, and whether the adhesive is waterproof.

purpose of use

Various types of polystyrene foams are used in settings ranging from building insulation to hobby model making. Expanded polystyrene foam (EPS) and extruded polystyrene foam (XPS) are the most common and most people refer to them as “Styrofoam”. Lightweight and usually white in color, EPS foam is used to make packaging peanuts, packaging materials, and lightweight craft foams. XPS foam, which is denser, is often used in more detailed models, e.g. B. in hobby and architectural building models. Many polystyrene-safe adhesives can be used with polystyrene foams.

When choosing a Styrofoam adhesive, consider the size, shape, and intended use of the foam. A thinner adhesive, such as A spray, for example, may work better for gluing large areas. However, for more detailed work, a thicker adhesive may be best. Also consider the intended use of the project – indoors or outdoors – and how much force the adhesive will have to withstand. Heavy duty or super strength options are available, as are adhesives for larger construction projects.

grip time

Different adhesives have different textures: some feel tacky immediately, while others take time to become tacky or develop a bond only after drying. For example, Styrofoam pieces can initially slide around when glued with a liquid craft/school glue, while hot glue can stick quickly. In this guide, “gripping time” refers to how long it takes for two glued pieces to “grip” or stay in place after gluing.

A tackier glue will help hold the styrofoam in place while the glue dries completely. Most products don’t advertise the exact stick time, instead using a few terms to denote a tackier adhesive, including “fast tack”, “fast set time” or “good bond strength”. However, do not confuse handle time with drying time.

dry season

The drying time (or cure time) refers to how long it takes for the adhesive to fully bond and reach its full strength. The drying time varies depending on the type of adhesive. Some styrofoam glue only takes a few minutes to dry, while others take 24 hours or more to cure. Hot glue dries in minutes. Sprays and multi-purpose glues usually take longer to dry, sometimes a full day. Construction adhesives can take days to fully dry.

For some projects, like model making, a shorter drying time is a necessity. No craftsman wants to wait a whole day between each assembly step. For projects with only one or two gluing steps, a longer drying time may not be an issue and could be a worthwhile compromise. For example, many construction adhesives take 24 hours or more to fully cure, but the result is a much stronger bond than hot glue.

waterproofness

Depending on the project, hobbyists need glue with additional properties. For example, use waterproof or waterproof glue for outdoor projects or to provide an extra layer of security. Waterproof adhesives do not dissolve when exposed to water. However, water-resistant adhesives degrade with exposure to water, but they don’t wash off as easily as non-water-resistant adhesives. Water-soluble adhesives can be removed with water, making them an excellent choice for crafts with kids.

Waterproof adhesives should not move when exposed to water. Using a waterproof glue will ensure the styrofoam will hold together even when submerged in water.

Our top picks

Whether it’s for an arts and crafts lesson with kids, a hobby craft, or building something substantial, having the right tools for the job makes all the difference. The list below provides an overview of the best Styrofoam adhesives to bring any Styrofoam creation to life.

Best Overall 1 Uhu POR Styrofoam Adhesive Photo: amazon.com Check Current Price Hobbyists who work frequently with styrofoam may want to choose a reliable styrofoam adhesive, such as this one from Uhu. It is specifically designed for use on polystyrene but is also suitable for wood, plastic, paper, metal, leather, ceramic and more. This adhesive is flexible, does not age, forms a permanent seal and is waterproof. Its quick drying time of 10 to 20 minutes makes processing easier. This glue dries to a clear finish to keep projects looking clean and professional. Product Specifications Type: Styrofoam Glue

Styrofoam glue Drying time: 10 to 20 minutes

10 to 20 minutes Waterproof: Yes Benefits Sets in quickly

Transparent version

Flexible and resistant to aging Disadvantages May cure too quickly for some applications Get Uhu POR Styrofoam Adhesive at Amazon and HobbyKing.

Best Value 2 Multipurpose Weldbond Adhesive Photo: amazon.com Check Current Price Most styrofoam adhesives are affordable, but a multipurpose option offers even more bang for the buck. Weldbond Multipurpose Glue can be used to bond a range of items from Styrofoam models to wood projects. A universal adhesive, this product can bond almost anything including wood, tile, glass, foam, stone and ceramic. Weldbond recommends it as a binder, primer, filler and sealer. The glue is easily thinned to create the ideal texture for any project. A non-toxic, non-flammable and smoke-free product, this water-soluble glue dries flexible and clear. Product Specifications Type: General Purpose

Drying time: 24 hours

Waterproof: No Pros multi-purpose adhesive

Safe for a range of materials

No fumes

Dries clear Cons Not waterproof Get Weldbond glue at Amazon and The Home Depot.

Best All-Purpose Glue 3 Gorilla Original Glue Photo: amazon.com Check Current Price For the casual hobbyist, an all-purpose glue like Gorilla Original Glue works well for hobby and home projects, including Styrofoam. This glue can stick to almost anything including wood, stone, metal, ceramic, glass and foam. When placed on a surface, it expands to seep into every nook and cranny to create a better seal. It’s safe for both indoor and outdoor use, and the finished seal is waterproof and temperature resistant to withstand hot, cold, and wet conditions. Adhesive dries to a brown finish but is sandable, paintable and stainable. Product Specifications Type: General Purpose

All purpose drying time: 24 hours

24 Hour Waterproof: Yes Benefits Works on many surfaces

Waterproof

Temperature Resistant Cons Visible when dry Get Gorilla Glue at Amazon, Ace Hardware, and The Home Depot.

Best Spray 4 3M Super 77 Multipurpose Spray Adhesive Photo: amazon.com Check Current Price Aerosol spray adhesives make it easy to apply a thin, even coat of adhesive. 3M Super 77 Adhesive is a versatile choice for use on light-duty projects such as B. Gluing foam, paper, foil, metal, plastic, fabric, paper and more. In addition, the spray is safe for photos when completing scrapbooking and archiving projects. Commercial strength adhesive creates a secure bond in 15 seconds to 30 minutes, depending on adhesive volume and materials. Rather than penetrating a surface like many liquid adhesives, the spray is designed to stay on the surface for a mess-free application. The spray evenly covers larger areas and dries clear. Product Specifications Type: Aerosol Spray

Aerosol Spray Drying Time: Up to 30 minutes

Waterproof for up to 30 minutes: Water resistant Benefits Easy to use

Good for large areas

Fast drying time Cons Spray can be difficult to control Get 3M Super 77 Spray Adhesive at Amazon, Ace Hardware, and The Home Depot.

Best Hot Glue Gun 5 Surebonder Ultra Series Dual Temperature Hot Glue Gun Photo: amazon.com Check Latest Price This glue gun from Surebonder has a number of features that make it safer to use with foam and other materials. To handle a variety of projects, the glue gun has a high and low temperature option, making it safe to use on wood, glass, metal, foam, flowers and fabrics. The insulated nozzle helps prevent damage and burns, while a metal stand and side ribs ensure the gun stays upright, preventing glue back-up. An automatic switch-off function switches off the glue gun after 30 minutes of non-use. Product Specifications Type: Hot Glue Gun

Drying time: Depending on the adhesive

Waterproof: Depends on the glue. Advantages Dual temperature

Insulated nozzle

Auto shut off Cons Hot glue sticks not included Get the Surebonder hot glue gun at Amazon and Toolbox Supply.

Best Heavy-Duty 6 Liquid Nails Heavy-Duty Construction Adhesive Photo: amazon.com Check Current Price Major construction projects require a heavy-duty construction adhesive. This construction adhesive from Liquid Nails is a strong, high strength, multipurpose adhesive suitable for both professional and DIY use. Ideal for indoor and outdoor projects, this adhesive can be used to install foam board, foam molding and molding, wafer board, plywood, chipboard and much more. This type of glue for styrofoam is useful for large-scale styrofoam projects, such as B. the construction of life-size models, or for construction hobby projects, such. B. the insulation of a tree house or a dog house. Water and weather resistant adhesive has instant tack to make positioning materials easier. For precise placement, it allows up to 20 minutes of working time before it starts to stick properly. Adhesive dries to a tan finish with a flexible, strong bond. Product Specifications Type: Structural Adhesive

Drying time: 24 hours

Waterproof: Waterproof professional quality adhesive

Suitable for a range of building materials

Super strong hold Cons Not fully waterproof Get Liquid Nails construction adhesive at Amazon and The Home Depot.

Our verdict

Designed for use on polystyrene, Uhu POR Styrofoam Adhesive is a dependable choice that creates an excellent bond with a clean finish. Those looking for a more versatile product can look to the Weldbond Multi-Purpose Adhesive, which can be used as an adhesive on styrofoam and a range of other materials, acting as a primer, sealer and filler.

How We Chose the Best Adhesives for Styrofoam

Choosing the right glue for styrofoam is important: the wrong glue can melt and quickly ruin the styrofoam. When choosing the best adhesives for Styrofoam, we first considered safety and effectiveness. We’ve selected adhesives that won’t break down delicate styrofoam to ensure craft projects or styrofoam models remain intact. We have selected adhesives from reputable brands with an excellent track record of manufacturing adhesives. Coupled with excellent customer reviews, the adhesives on our list are the best adhesives for gluing styrofoam.

Applications for Styrofoam vary widely, as do the preferred methods of gluing it together. To cover a range of projects we have selected the best product for the main application (including all purpose adhesive, spray adhesive and heavy duty adhesive). We also considered affordability. Don’t use expensive styrofoam glue when a budget-friendly option works just as well.

Tips for gluing Styrofoam together

Gluing Styrofoam together or to other materials is fairly easy with the right glue, making finding the right glue an important first step. Some glues don’t work very well with styrofoam and others can even melt or dissolve the foam. Make sure the glue can hold on styrofoam as well as on any other surface.

Always follow the product’s instructions for the best grip and pay attention to the manufacturer’s safety instructions. If necessary, clean and prepare the surface by removing loose pieces of Styrofoam, dirt and dust that may affect the adhesion of the adhesive. A thin, even layer of glue is usually sufficient. Because some adhesives stretch, using too much can cause them to leak out the sides. Although Styrofoam is lightweight, it can still slip and shift if the glue isn’t sticky enough to hold it in place. Hold the pieces together tightly until the glue has set.

Most adhesive products can be used more than once. Tighten the lid of the container to prevent drying out and store as directed.

Choose a styrofoam-safe adhesive

Follow safety instructions

Make sure the styrofoam surface is free of dirt and dust

Use a thin, even layer of glue

Store as indicated

frequently asked Questions

With the right product, gluing Styrofoam is easy and the surfaces bond without damage or mess. There are a number of options available, and whether you’re using regular craft glue or Styrofoam glue, keep these tips in mind as you work on your next project.

Q. What is the best adhesive for foam board?

Spray adhesives work well with foam board and can cover a large surface evenly and quickly.

Q. What glue can I use on styrofoam?

A variety of adhesives can be used on polystyrene, including some craft glue, general purpose glue, spray glue, and styrofoam glue. Ingredients can vary from glue to glue, so double-check the label to make sure the glue can be used on styrofoam, polystyrene, or foam. A small patch test will help ensure the adhesive is safe and effective.

Q. Can I use superglue on styrofoam?

Superglue is often not the best choice when working with styrofoam as some products can cause the styrofoam to melt a bit. Instead, opt for one of the all-purpose glue or styrofoam glue on this list.

Q. At what temperature does styrofoam melt?

Styrofoam melts at 464 degrees Fahrenheit.

Q. How do I glue two pieces of styrofoam together?

Make sure the styrofoam surfaces are clean and dry before applying any suitable glue. Follow the glue’s instructions to apply and cure, and you should be done!

Q. How do I remove excess glue from styrofoam?

Water-soluble adhesives can be removed with water (and some soap if necessary). Other adhesives may require a solvent such as diluted acetone. However, solvents can also damage Styrofoam, so be careful when removing glue with these chemicals.

Q. Is Gorilla Glue safe for styrofoam?

Many Gorilla adhesive products are safe to use on styrofoam. If in doubt, make a small test spot on an inconspicuous area.

Choosing the best spray adhesive for the job

When choosing a spray adhesive, there are many options to choose from. Are you looking for a product that dries quickly, sticks quickly and holds up well in high temperature environments? Perhaps your business deals in foam and fabrics and you need a spray adhesive that will bond well in that environment. If you work with wood, you may be looking for an all-purpose product that will bond a variety of materials together. Whatever your specific needs, there’s a fast-setting spray adhesive that’s tailored to meet your exact needs. In this article we look at some products that have unique properties and are suitable for general use. Safety is always a concern, so be sure to check Safety Data Sheets (SDS) to ensure the product you choose will work in your environment.

Best high strength spray adhesive

Our pick for the best high strength spray adhesive is Camie 365 spray adhesive. This general purpose spray adhesive is part of the Camie-Campbell, Inc. line of products. They have been manufacturing adhesives for over 60 years and are backed by superior products, excellent service and technical expertise in the field. Camie 365 is an excellent choice for construction applications where fast tack and high bond strength are a must. 365 is also a unique solution for bonding dissimilar substrates and performs better than other aerosol adhesives when tested under thermal stress conditions.

Camie 365 is a fast setting product that typically achieves green strength in 10 seconds to 2 minutes. It works well with the most common building materials such as plastics, metals, foams, fabrics and wood. It creates a permanent bond that is high strength, withstands high temperatures and is water resistant. Using highly absorbent materials, this product has low penetration which means more adhesive is left on the surface where you need it. The spray can has a three way nozzle which allows the user to adjust the spray pattern of the web and as the spray is colorless matching an existing spray pattern is not usually a problem.

Best aerosol glue for foam and fabric

Bostiks SuperTak Foam and Fabric is the ideal spray adhesive for use on fabrics, including foam. If you are in general upholstery or marine interiors this is the product you have been looking for. If your business requires excellent bonding of various fabrics and films, Bostik Super Tak is an excellent choice. It bonds quickly and remains pliable and easy to work with, giving you a smooth glue line with no indentations. Super Tak is designed to bond fabric to latex, urethane and foam, as well as polyethylene, wood and plastics. It gives off a controlled lace pattern and the orange color ensures your coverage is complete.

Super Tak bonds to a single surface in 1 to 5 minutes and to two surfaces in 1 to 10 minutes. The final bond is permanent. A key feature of this product is its low soaking properties. This is especially important when gluing fabrics, as the glue needs to remain on the surface for as long as possible to achieve maximum adhesion. Like all Bostik aerosol spray adhesives, they are environmentally friendly as they contain no ozone-depleting chemicals such as methylene chloride or chlorofluorocarbons.

Best high strength spray adhesive

If you are looking for the best high strength spray adhesive then 3M Hi-Strength 90 Spray Adhesive is a reliable choice. 3M is a household name these days, but what most people probably don’t know is that it began as the Minnesota Mining and Manufacturing Company in 1902. Today, their product line of over 60,000 products is sold worldwide. One of their successful product lines are adhesives.

Hi-Strength 90 has been in the 3M family for many years and has earned a reputation as a solid performer in a variety of applications from hobby shops to general maintenance and repair. Hi-strength 90 is an excellent multi-purpose adhesive that dries quickly and gives an incredibly strong bond. This product even works on concrete!

This is an excellent product for heavy commercial applications where industrial strength is required. It is recommended for felt/cloth, rubber, wood, glass and soft foam. Another use is the installation of acoustic panels. Its properties include high heat resistance, super fast tack, low seepage and moisture resistance. The product comes with an adjustable nozzle that offers a variety of spray patterns, allowing you to apply the adhesive directly to the surface being worked on, minimizing waste and cleanup.

Best spray adhesive for wood

Weldwood 122 is the ideal choice when you need the best spray adhesive for wood applications. Manufactured by DAP, the Weldwood range of adhesive sprays are renowned for their consistent performance as a superior wood joining product. DAP added the Weldwood line of adhesives to its line of products in the 1980’s and can be found in most home improvement and major department stores across America.

Weldwood 122 is an economical choice in the spray adhesive market, yet still offers many of the same benefits that more expensive products offer. Firstly, it is a high strength adhesive which makes it an excellent choice for the hobby shop owner. It adheres to wood, plywood and laminates, as well as plastics, leather, paper, trim, fabric and rubber. It sets instantly so no staples are needed and sets up in about 10 minutes.

Weldwood 122 is moisture resistant and heat resistant. Another benefit of this product is its availability in quarts and gallons for larger jobs that require a more extensive application. 122 can be used for indoor and outdoor applications and may be the only spray adhesive you need in your shop.

Best fast tack spray adhesive

Our proprietary Prime Industries Fast Tack Spray Adhesive is the ideal choice when you need a fast tack solution. Fast setting spray adhesives have become the go-to choice for most hobby shops and handymen. They are easy to use, easy to store and work well for most applications.

The advantage of a quick-setting adhesive is that you can usually go without staples while the adhesive dries. Some products stick instantly, while others give you a few seconds to a few minutes to adjust the project for perfect alignment.

Spray adhesives typically offer similar properties that are important to all users. High strength and high temperature resistance are essential when working on larger projects. A little soaking is required if you plan to use absorbent materials. The ability to stick to a variety of materials will also be high on the list. Some products have nozzles that distribute different spray patterns that can be beneficial for certain industries. With all the options available on the market today, finding the right product for your needs is easier than ever. A list of all our aerosol adhesives can be found in the Prime Industries online shop.

Specially developed for foams and fabrics

A top spray pattern optimized for foam bonding is dispensed with

Provides professional, industrial strength for demanding applications

Provides a fast, aggressive tack for quick assembly of highly stressed joints

Allows a bonding time of 15 seconds to 30 minutes

3M™ Foam Fast 74 Spray Adhesive is a fast-drying spray adhesive that bonds foam and fabric to a variety of substrates. His enduring commitment delivers quick results to move projects forward. The non-yellowing formula spreads easily in a peak spray pattern and can be applied directly to surfaces and materials when needed.

Fast acting, long lasting

3M™ Foam Fast 74 Spray Adhesive is a long-standing member of 3M’s portfolio of go-to adhesives for everyday use, considered by many to be essential on the shop floor. For many, getting the job done is just a spray away.

Our 3M™ Foam Fast 74 Spray Adhesive has an aggressive tack that offers high initial tack with foam tear resistance, yet still provides enough open time to position materials properly. The high solids content supports the low pull-in property and gives you time to optimally position the parts. This attribute also offers higher opacity than competitive spray adhesives and helps create soft glue lines without dents. The top spray pattern of its non-yellowing adhesive combined with its quick tack, strong bond and clean appearance make it ideal for projects of all kinds. 3M™ Foam Fast 74 Spray Adhesive is also offered in low VOC aerosols, nonflammable cylinders and bulk .

Allows for firm foam adhesion for large and small applications. Allows for firm foam adhesion for large and small applications

General padding

foam lamination

Attaching foam and fabric to wood and other substrates

Install acoustic panels

3M™ Foam Fast 74 Spray Adhesive is capable of bonding foam and fabric to a variety of materials including paper, cardboard, plastic, metal, wood and more. This spray adhesive has proven itself for large and small projects. Additionally, our low VOC <25% CA spray adhesive is CARB compliant and eligible for LEED® credits. When developing the 3M™ Foam Fast 74 Spray Adhesive, we wanted to overcome the obstacles encountered when applying the existing adhesives on the market. By inventing a unique "spray adhesive" 3M was able to provide a self-contained adhesive solution that saved both time and money.

We know that spills can happen with any DIY project, and we want to help you with tips and tricks to successfully remove glue from fingers and nails.

For bonded skin, please call 1-800-420-7186 to speak with a doctor.

To remove Gorilla Spray Adhesive from fingers and nails, we recommend the following steps:

If the adhesive is still damp, wipe it off with a dry cloth, then wash the area with soap and warm water. After hardening, rinse well with warm water.

How do I remove Gorilla Spray Adhesive from my surface?

To clean the surface while the adhesive is still wet/uncured, wipe the adhesive off the project with a dry cloth. Isopropyl alcohol (IPA) can be used according to the manufacturer’s instructions.

Once cured, Gorilla Spray Adhesive can be mechanically removed by gently scraping the surface, being careful not to damage the underlying surface.

features

This spray adhesive is recommended for use with both open cell and closed cell foams. 3M Super 77 is commonly used for custom packaging, crafts, cushions and acoustic foam assembly.

Do not use 3M Super 77 to bond polystyrene materials. The chemical structure of this glue melts the foam. Alternatively, Camie 373 can be used.

Whether you’re rebuilding an engine or helping your child with a school project, things always go better when you have the right tools for the job. This is true in the world of foam, too, from home improvement projects to companies that make custom couch cushions, foam mattresses, or foam gaskets.

Foam Factory, Inc. offers a wide variety of foam products and therefore spray adhesives designed to work best with each type of foam offered. This particular post will help you better understand why something so seemingly simple is surprisingly complex and how to choose the right product with our detailed breakdown to ensure you always have the right adhesive for the job.

—

First, a little background on why sticky foam is such a unique situation:

The need for different types of adhesive can be traced back to the variety of foams. In terms of feel, appearance and performance, open-cell foam and closed-cell foam differ significantly. The differences are not just cosmetic, however, as the differences between foam types are due to individually unique chemical and molecular structures. So while open and closed cell foams are still part of the same family, making them from very different compounds creates a number of variables when they need to be manipulated. In this case, it affects how a foam responds to adhesive. Depending on the foam type, some adhesives may not create a permanent bond, while others have a physical reaction and can damage or destroy the foam.

Fortunately, manufacturers have recognized the unique problems of foam bonding, and special adhesive formulations exist to properly bond all different types of the material. Of course, having multiple adhesive options without knowing which one is best for your application brings its own problems. For your convenience, we have created a detailed list of our three types of spray adhesive.

Under each type of spray adhesive we carry we have listed and linked the types of foam that they work best with and those that should not be used with them. Whether you’re gluing two pieces of the same material together or gluing to most substrates, simply find the foam you want to work with and you’ll know what type of spray adhesive to use for your project!

Spray Adhesive: Claire Mist

DO NOT use with: Closed cell foam

Use With: Open Cell Foam

This includes all densities, colors and strength values ​​of:

– 3LB ViscoSAVER

– 4LB ViscoPLUSH

– 5LB ViscoMAX

—

Spray adhesive: 3M Super 77

DO NOT use with: Closed cell expanded polystyrene (EPS) foam*

Use with: most closed cell foams AND all open cell foams**

This includes all densities, colors and strength values ​​of:

*The formulation of 3M Super 77 physically melts EPS foams, damaging and/or destroying the material.

**3M Super 77 bonds more strongly to open cell foam than Claire Mist, but is more expensive. Claire Mist is the economical choice for all but the most demanding open cell foam projects.

—

Spray Adhesive: Camie 373

DO NOT use with: open cell foam OR most closed cell foams***

Use With: Expanded Polystyrene Foam (EPS)

***Camie 373 is specifically designed for use with expanded polystyrene foam (EPS) to prevent damage from other adhesives.

If you have additional questions about gluing foam after finding the right adhesive, check out our PDF on using spray adhesive with general foam products or contact us for more information!

IMPORTANT: Spray adhesive is not suitable for gluing acoustic foam to painted or bare concrete or concrete block walls. For more information, see the PDF linked above.

A truly versatile adhesive can be hard to come by. While very few (if any) glues will cover every single application you need for your cosplay, there are a few general purpose glues to keep in your kit that will work for just about anything you need to glue together. A glue of choice that can cover a variety of common cosplay materials and situations is your standard super glue (also known as CA glue).

Superglue is an incredibly permanent adhesive that goes a long way in holding your costume components together. In this post, we discuss the best uses of super glue in cosplay and the benefits and challenges of working with it.

Best Uses for Super Glue in Cosplay

Superglue is an incredibly versatile adhesive that works with a wide variety of common craft, household, and especially cosplay supplies. It is made from an acrylic resin called cyanoacrylate, which creates a strong chemical bond between surfaces. Superglue in particular is an ideal adhesive for EVA foam armor, props and other cosplay parts. Essentially, you can use super glue in any foam application that you would also use contact cement for. Because super glue usually comes in a small bottle, it’s great for controlled application when gluing small EVA pieces, but you can make entire sets of EVA armor using just super glue. It is also safe for attaching LED strips to EVA.

You can also use super glue to attach plastic pieces together. Superglue works on PVC, ABS plastic, styrene, acrylic and, according to Bill at Punished Props, basically any modeling plastic you might be working with. It’s best to sand down the plastic surfaces you’re gluing together to give the superglue some grip. Similarly, superglue is also a great adhesive for ceramics and 3D printing material. Bill uses super glue to attach all of his 3D printed parts.

In addition, superglue can be used to seal rough edges on a variety of materials. It can stop fraying on the edges of some fabrics and reduce “lint” on the cut ends of MDF (medium density fiberboard) before sanding the wood smooth.

However, as mentioned above, most adhesives don’t work on every single cosplay material. You should be aware that superglue is not a viable option for insulation foam or styrofoam. Because of its chemical properties, superglue can actually melt this type of foam.

Benefits of working with superglue

Superglue is a useful multipurpose glue for several reasons. Here are the benefits of working with super glue.

Super glue is available at craft stores, craft stores, and most retailers.

Super glue is available at craft stores, craft stores, and most retailers. It comes in a variety of grades and viscosities, meaning you can choose the thickness of super glue that works best for your specific purposes.

Thin superglues have an almost watery consistency that makes them perfect for gluing in tight spaces. While thicker glue can clump out when parts are pushed together, thin CA can seep into the smallest cracks.

Medium viscosity CA is great for filling gaps in your seams or accidental tears in your foam.

Mixing it with something like baby powder can turn super glue into a sandable paste that also fills in gaps and repairs holes.

Superglue comes in small bottles that are easy to carry to fix mistakes, even if you don’t have much space to carry it in your kit or bag. There are a few different bottle sizes to choose from depending on how much you need.

Additional products can be used to both speed up and remove the bonding of the super glue.

Superglue is permanent (unless used with remover), dries clear, and is paintable.

Super Glue Challenges

However, as with all glues, there are some challenges to overcome when using super glue in your cosplay. Here are a few to keep in mind:

Superglue can be relatively expensive. Because it’s only sold in relatively small bottles, it can be expensive to buy and refill, especially if you’re going to use it as the glue for most of your cosplay.

Also, bottles of superglue tend to get crusty and sticky fairly quickly. This can cause your glue to dry out or make it difficult to squeeze the glue out at all. To counteract this, you can buy replacement caps to swap in and out, but this will incur a small additional cost.

Superglue will cloud clear plastics, so it’s not the best choice for lenses and other transparent parts.

Prolonged use of superglue can produce toxic fumes. If you work with superglue for long periods of time or in large quantities, you will likely need to wear a mask or work in a well-ventilated area.

Superglue sticks to your skin. It can stick your fingers together and it can stick your fingers to the material you are working with. It’s a good idea to either wear gloves if you’re using a lot of superglue, or have a bottle of remover nearby.

While superglue sets relatively quickly, it’s not an instant hold. It may take a few seconds and start to pull apart on EVA if you don’t use the spray accelerator.

Superglue: A last-minute lifesaver

In the world of glue, one of the most common and strongest glues you can use for cosplay is super glue. Its strength and versatility make super glue a favorite for many cosplayers, using it as their main glue of choice. Perhaps the best thing about super glue, though, is that it always comes in handy when you’re in a pinch. If you’re working on a cosplay and it’s hanging by the wire, you might not have time to run for more hot glue sticks or order more contact cement, but if you have a tube of CA you can still get it done in time. If you have a tiny travel tube of superglue in your pocket or just tucked away somewhere in your cosplay, you can make last-minute repairs during a convention or photoshoot without the hassle of finding something else that works. While superglue is a great solution to many average cosplay situations, its real superpower is a last-minute emergency failover.

What is polyurethane?

Polyurethane, also known as PU, is a polymer made from the combination of an organic compound unit with carbamate (urethane).

PU is available in different forms; rigid solid, foam or soft elastomer, making it an extremely versatile material for a range of end-user applications.

Applications of polyurethane include roof insulation, insulated panels, windows and doors in construction (rigid foam), thermoplastic polyurethane in medical devices to coatings, adhesives, sealants and elastomers for the automotive industry.

Adhesives for bonding polyurethane

It is important to consider the type of PU to be bonded before selecting the adhesive for the application.

Cyanoacrylate adhesives generally bond well to PU, with grades such as Permabond 731 and Permabond 2050 being best suited to elastomeric PU.

For bonding flexible PU we recommend the Permabond Flex CA range, which maintains the softness and flexibility of the bonded substrates compared to standard cyanoacrylates.

For gluing foam PU, you may need to use an activator like Permabond CSA-NF, which accelerates the curing speed and allows the cyanoacrylate adhesive to bond porous surfaces.

SMP Merbenit IA45 is a flexible adhesive for bonding PU foam to many substrates.

For gluing hard PU we recommend the use of polyurethane adhesives such as Araldite 2018 and Araldite 2028-1 and structural acrylic; Permabond TA4204.

For bonding PUR substrates in the automotive and transportation industries, we have a range of polyurethane adhesives from the Dow Betaseal portfolio that are suitable for these applications.

Surface preparation for gluing polyurethane

It is important to ensure surfaces are clean, dry and free from contamination before using adhesives to bond PU. You can use isopropanol or an impregnated cloth such as Wipemaster Wipe 9 IPA Wet Wipes to clean the surface.

For tips on best surface preparation methods, see our post: Surface Preparation for Adhesive Bonding.

Contact us for specific product recommendations on a suitable adhesive for bonding PU

If you are looking for tips on gluing other plastics, read: What you need to know about gluing plastics

Please share!

0 shared pin

Split

tweet

Adhesives are one of the most functional tools that we use for various purposes, from creating crafts and artwork to fixing and mending things. One of the most popular glues that we are all familiar with is Elmer’s glue. But do you know which surfaces Elmer’s glue works (or doesn’t) work on?

Elmer’s Glue can work on porous surfaces such as paper, card, Styrofoam, canvas, fabric, felt, pottery and ceramics, wood and leather. However, it cannot work efficiently on non-porous surfaces such as metal, plastic, and glass.

Here is a table of Elmer products and their compatible and non-compatible finishes:

Does Elmer’s Glue work on paper?

Paper is one of the cheapest and most widely used materials to create children’s craft and school projects. It is also widely used in offices, colleges, art studios and many other places.

Elmer’s glue works very well on paper. Along with its regular bottle glue, Elmer’s glue stick is safe and easy to use, especially for children. These products are also non-toxic and washable. A more specialized product is Elmer’s Craft Bond, which is bleed resistant.

Does Elmer’s glue work on plastic?

Plastic is everywhere, and almost everything we use today is made from it or has some plastic parts. Gluing broken plastic items is a simple and inexpensive method that helps keep them in use longer and is also good for the environment.

Since Elmer’s glue is a common type of glue found in almost every home, it would be a helpful tool in most home projects.

Elmer’s Glue-All will not work on plastic surfaces as they are non-porous. While it seems feasible to bond some plastic surfaces with Elmer’s glue, it doesn’t stick well and the resulting bond won’t be strong enough to hold it.

White glue, including Elmer’s glue, was developed for porous surfaces. Why? Because when you apply it to such surfaces, the glue will be absorbed through its tiny pores and cracks. After the solvent evaporates, the glue hardens and acts like a dovetail holding the two pieces together.

Because of this, Elmer’s Glue-All will not work on non-porous surfaces such as plastic. They have no pore through which the glue could penetrate and form a bond.

Does Elmer’s glue work on wood?

Wood is another common material around the houses; It is used in furniture, flooring, cabinets and many other places. You can also use it to create crafts and decorative artworks.

Gluing pieces of wood together is an easy, safe, and clean way to repair or create new wooden items. But does Elmer’s glue work well on wood?

Elmer’s glue works well on wood; It is one of the glue’s favorite surfaces. It dries quickly and forms a strong bond with its porous surface. For minor damage and light work, however, Elmer’s all-purpose glue is best. For heavier projects, choose a wood-specific glue, like Elmer’s Carpenter wood glue.

Because Elmer’s Glue-All is water soluble, the resulting bonds can weaken and even break when exposed to water or moisture. You can use it on light woods like balsa and it works great.

However, if you are considering repairing or repairing pieces of furniture or other bulky wood construction, Elmer’s Carpenter Wood Glue is your best bet. It’s another product with much stronger adhesion that works great on wood and lasts a long time.

Does Elmer’s glue work on metal?

Metal is also a common material that can be found almost anywhere, from kitchen utensils to doorknobs, window frames, some pieces of furniture or decorative items such as sculptures. Imagine accidentally breaking the handle of your favorite metal camping kettle.

What would you do to fix it? Probably the easiest way you can think of is gluing. But does Elmer’s work on metal?

Regular Elmer glue will not work on metal. Metal is a non-porous surface and Elmer’s glue doesn’t bond well with it. But Elmer’s Glue-All can create permanent bonds with metal. It can also be sanded and painted. However, for heavy pieces of metal, welding is the wiser choice.

With Elmer’s Glue-All, you can quickly repair small, lightweight metal parts and achieve the desired result. But when the metal surfaces you want to bond together are heavy and bulky, adhesives can fall short. It is better to weld them and get a strong permanent connection.

Does Elmer’s glue work on styrofoam?

Styrofoam is a type of material made from a petroleum-based product called styrene. It’s commonly used in the manufacture of food packaging, appliance insulation, and even surfboards.

Therefore, there are so many situations when you need to fix and glue a styrofoam item. But what goes with styrofoam to stick cleanly?

Elmer’s glue (even his regular school glue) works efficiently on styrofoam. It is an excellent choice for attaching styrofoam blocks and creating simple artwork or crafts for kids. It dries quickly and clear and is also safe for children.

Elmer’s liquid adhesives are a great choice for working with styrofoam, and you don’t have to worry about the adhesive temperature ruining your job—glue that’s too hot can melt the styrofoam.

Does Elmer’s glue work on leather?

We have all used leather items such as bags, belts, shoes, jackets, gloves, sofas and many more in our lives. Leather items can tear apart and need to be repaired. You may also want to attach other things to leather or make crafts out of it.

Gluing leather seems doable, but it’s not that easy and you need to choose the right type of glue for it to stick at all. Can Elmer’s Glue work on leather or not?

Elmer’s Glue-All’s new formula makes it a great choice for working with leather, especially if you’re on a budget. It dries quickly and creates strong, permanent bonds. If you want a waterproof type, you can use the Max version.

Does Elmer’s glue work on felt?

Felt is an ancient, durable material that is still used in a variety of industries, from furniture upholstery, clothing and curtains to making crafts and toys.

Gluing is a simple, safe and inexpensive way to connect pieces of felt together. But which glue works on felt?

Along with regular Elmer’s glue, Elmer’s craft glue – also known as pressure sensitive glue – works beautifully on felt and dries clear and clean. Elmer’s glue is safe and non-toxic, making it a great choice for kids’ projects or toys. But it also works for your own crafts and artwork.

In addition to Elmer’s craft glue, school glue also works well on felt – but with less adhesion. Elmer’s glue penetrates the tiny fibers of the felt and bonds firmly to them. However, when it dries it can harden the felt a bit.

Elmer’s Craft Glue works on porous and semi-porous surfaces, perfect for felt because of its no-run formula.

Does Elmer’s Glue work on cardboard?

Cardboard boxes are widely used in various areas of our life, used both in the home and in industry. We use them for storage, to create artwork and crafts, to package products, or for other purposes. But what is the best cardboard glue? Does Elmer’s glue work on them?

Elmer’s Glue works on cardboard and is one of the best products for gluing this type of material. Cardstock has a porous surface, making it ideal for Elmer’s glue. Elmer’s School Glue is super easy to use and clean, safe for kids, and dries clear. However, the glue-all version is much stronger.

The only point to remember is that when gluing fabric to cardboard, the glue’s solvent, i.e. water, can get into the cardboard and soak it, ruining your project.

Does Elmer’s glue work on fabric?

Another material that we all deal with on a regular basis is fabrics and fabrics; from our clothes, bedding, curtains and furniture to handkerchiefs, car seats, etc. are made of textiles.

Even many works of art and handicrafts are made of fabric, and one of the easiest ways to make them is by gluing.

Elmer’s Glue with its original formula can work on fabric, but the resulting bonds may not be very strong. It is water soluble and easy to clean, so it is better not to use it for fabrics exposed to water, such as fabrics. B. Clothes. However, the Glue-All formula is better able to achieve the desired result.

The fabric is porous, allowing it to easily absorb the adhesive and form strong, long-lasting bonds as it dries. However, if you plan to use Elmer’s School Glue to repair clothes or for customization, you need to know that it doesn’t last long because this glue dissolves in water.

Also, Elmer’s glue can harden the fabric. So consider a stronger but specialized glue like the Tear Mender or even sew the fabrics if possible.

Does Elmer’s glue work on glass?

While glass is also widespread and somehow ubiquitous in our lives, it is also common for glass to break and need repairing.

Perhaps you want to seal a tiny crack or break in the glass of your window or repair a broken glass sculpture. In any case, gluing is the easiest method. The question is, does Elmer’s glue work on glass?

Elmer’s original adhesive formula will not work on non-porous surfaces such as glass and the resulting bond will not last long. But its Glue-All version (specifically Glue-All max) bonds efficiently to glass and is waterproof. Elmer’s China and Glass Cement is also a reliable option.

Elmer’s China and Glass Cement, available on Amazon, is clear, dishwasher safe, and non-toxic. You can therefore use it to repair broken glass without hesitation.

Does Elmer’s glue work on canvas?

Canvas is a type of fabric made from cotton or linen. It is mainly used to create artworks but is also used for outdoor purposes due to its durability. It can also be found in bags and backpacks, cases or tents.

You can use glue on canvas for many reasons. For example, you might be an artist trying to tape your canvas to a board and paint on it. How you do that?

Elmer’s glue can work on canvas because it’s a porous surface and the glue can penetrate and dry. In fact, all PVA glues are good choices for gluing canvas. Elmer’s glue dries quickly and clear with minimal mess or residue. You can also wipe away the unwanted glue with water.

However, Elmer’s glue is acidic, which can have undesirable effects on your canvas. It is better to choose neutral PVA glue for your canvas. But if you must use Elmer’s glue, mix it with chalk powder and water to neutralize it.

Does Elmer’s glue work on rubber?

Rubber is a type of flexible polymer that stretches and shrinks. Composed of natural and synthetic materials, it is widely used in toys, pacifiers, medical devices, balls, protective pads and many other products. Does Elmer’s glue work on rubber?

Regular Elmer’s Glue or School Glue won’t work on rubber, but Elmer’s Contact Cement is another beast designed specifically for such applications. It can firmly adhere to materials such as plastic, metal, rubber, glass and others to create strong, long-lasting bonds.

You can glue almost anything with Elmer’s Contact Adhesive. For example, you can use it for surfaces like a countertop and attach laminates (thin layers of plastic) to it, or glue tiles to the floor.

It is a highly adhesive substance developed for machining non-porous materials. When we glue surfaces made of these materials, the water present in the glue cannot escape and does not dry out.

However, contact cement needs about 15 to 20 minutes to dry before joining the surfaces. Also, it needs to be applied to both parts so that it adheres to itself and creates a flexible bond.

Does Elmer’s glue work on ceramic?

Another very common substance that we use in our daily lives is pottery – pottery, porcelain or china. They are made of clay and heated to become hard and durable.

However, ceramic items such as crockery or decorative antiques are fragile and prone to breakage. Gluing is a safe and inexpensive way to attach things like this.

While Elmer’s Glue-All works well on ceramics and pottery, Elmer’s has introduced a special product for such materials. Elmer’s China and Glass Cement is also dishwasher safe and non-toxic, making it a great choice for kitchenware. It’s also great for outdoor items like pots.

A guide to Elmer’s products and their surface compatibility

Here is a table of Elmer products and their compatible and non-compatible finishes:

Product Surfaces It works on surfaces it doesn’t Key Features Buy Online Here Elmer’s School Glue Paper, wood, cardboard, styrofoam, felt, canvas, metal, glass, plastic Safe, washable, non-toxic, non-running formula Amazon Elmer’s Glue-All Paper Fabric, Wood, Ceramic, Leather, Metal, Glass, Stone Non-Safe, Non-Toxic, Quick-Drying Formula, Sandable, Paintable & Waterproof Cardboard, Notice Board Metal, Plastic, Glass, Acid-Free, Photo-Safe, Non-Toxic & Washable Amazon Elmer’s Craft Glue Wood, Cloth, Paper Metal, Plastic, Glass Strong wet adhesion for multipurpose projects, dries clear and no-run formula Amazon Elmer’s Carpenter’s Wood Glue Wood Metal, Plastic, Glass Great for carpentry and home repairs. Non-toxic, no harmful fumes, easy to clean with water and more sticky than wood. 20 to 30 minute clamp time and 24 hour full bond Amazon Elmer’s Glue-AllMax Anything including stone, metal, cer amic, wood, foam, glass None Waterproof for interior or exterior use, sandable and paintable Amazon Elmer’s China & Glass Cement Glass, Ceramic, Ceramic & Porcelain, Plastic None Dishwasher safe and non-toxic For indoor or outdoor use Dries clear, dishwasher safe and non-toxic Amazon Elmers Contact Cement Plastic, metal, rubber, glass, wood, laminate Non-neoprene rubber for an ultra flexible bond, convenient and quick drying Amazon

Elmer’s glue story

Elmer’s is a renowned US-based company engaged in adhesives, crafts, home repairs and office supplies. His adhesives come in white, squeezable plastic containers with orange caps, which are his trademark.

It might seem strange to see a smiling cow as the logo of an adhesives company like Elmer’s. However, this logo is based on “Elmer the Bull”, the spouse of Borden’s advertising symbol “Elsie the Cow” – Borden was a famous manufacturer of food, particularly dairy.

It was originally introduced by the Borden company in 1947 and operated under their name. His first glue product, known as Casecorez Glue, was based on casein, a milk by-product.

After the Second World War, the Borden company expanded its activities to synthetic resin glues. It introduced the first multipurpose white glue known as Elmer’s Glue-All, albeit with a different packaging than today.

However, in 1999 Elmer’s was spun off and was acquired first by Berwind Corporation in 2003 and later by Newell Rubbermaid in 2015.

Elmer’s Glue ingredients

Elmer’s Glue (or Elmer’s Glue-All, to put it correctly) is a white, watery glue substance familiar to most of us. It is also known as wood glue, white glue, school glue or PVA glue. But let’s take a closer look at its ingredients.

Elmer’s Glue is an emulsion of polyvinyl acetate, polyvinyl alcohol, and propylene glycol with a few other additives. Also, Elmer’s glue is about 50% water.

Polyvinyl acetate is a synthetic material (also known as synthetic resin), which is the main reason Elmer’s is known for not using any animal-derived ingredients in its adhesives.

Elmer’s Glue works on many surfaces, bonding porous and semi-porous materials like wood, fabric, and paper. It is non-flammable and also safe to work with bare hands.

As previously mentioned, Elmer’s Glue is an emulsion; About half of this is made up of a solvent (water), and when it evaporates, the vinyl polymer strands bonded together are left behind.

It dries well at room temperature and with good air circulation. It takes at least 30 minutes to dry, but reaches its full strength after 8 hours. However, depending on the ambient temperature and the amount of adhesive used, these processes can take longer or shorter.

Final Thoughts

Despite its excellent adhesion to many materials, Elmer’s School Glue is water soluble; That’s why it’s so popular with teachers and parents and often used in school projects. What most people don’t realize, however, is that there’s an Elmer Glue for every project imaginable. I hope this article has helped shed some light.

Thank you for reading!

For more information, see What surfaces does Gorilla Glue work on? | Complete Guide.

Hey, I’m Jim and I’m the author of this website. I’ve always been interested in survival, fishing, camping and all things natural. When I was growing up, I actually spent more time on the water than on land! I’m also a best-selling author and have degrees in history, anthropology and music. I hope you find value in the articles on this site. Feel free to contact me if you have any questions or input!

Please share!

Wear and tear is inevitable and sometimes your mattress will tear. With the help of a memory foam adhesive, a tear in the memory foam doesn’t have to mean the end of your mattress. Memory foam mattresses in particular can be a costly investment that makes a tear or hole even more frustrating, so the existence of this adhesive is good news for mattress owners. Before you start repairing your memory foam mattress, first consider the type of foam, the type of glue needed, and the type of tear.

If you want something incredibly strong to hold your cosplay together, you have a few sturdy options to choose from. When it comes to intense permanent adhesives, E-6000 is a popular choice among cosplayers and prop makers. Remarkably versatile, E-6000 is a great choice for heavy and light materials, large and small applications, and just about anything else you need to connect in your cosplay. If you’re looking for a reliable glue you can count on, this could be it. In this post, we discuss the best times to use E-6000 glue for cosplay and explain the pros, cons, and safety precautions associated with its use. (Image: chadmagiera)

Best Applications for E-6000

E-6000, in case you are unfamiliar, is a solvent based industrial adhesive sold in a squeeze tube and is also suitable and recommended for a variety of craft and hobby uses. It’s a viscous, gel-like consistency that could be compared to maple syrup, and it becomes stickier when exposed to air. Perhaps one of E-6000’s most unique attributes is that it is equally well-suited to adhesive applications large and small. To give you an idea, some manufacturers swear by E-6000 for adding gems and rhinestones to their costumes, while others find it perfect for assembling full armor and props. Because of its strength and versatility, E-6000 is a popular choice for a variety of cosplay applications.

In fact, E-6000 can be used on both porous and non-porous cosplay materials. The list of materials that can be used is long: leather and sturdier fabrics, fiberglass, plexiglass/acrylic, metals, wood, paper, ceramics, glass and craft/EVA foam, just to name a few of the most popular. However, one note we would like to add now is that E-6000 will NOT work with insulation foam. As far as materials go, that’s pretty much the only exception. In terms of specific applications, E-6000 works well for stitching, attaching details and bonding structural parts.

Benefits of working with E-6000

There are a variety of reasons why E-6000 is a popular glue for many cosplayers. Here are some of the benefits of working with it:

E-6000 offers one of the strongest bonds of any adhesive. Once you have glued your materials together they will not fall apart without the use of a solvent based glue remover.

It is relatively easy to apply directly from the tube or with a tool such as a brush or toothpick.

Because you can choose your application style and tool, you can be very specific about where you apply E-6000.

In general, E-6000 is available in three colors: clear, white and black. This glue is also paintable so you can cover it with the same color as the rest of your cosplay or prop.

The adhesive quickly “cures”, becoming tacky and holding your materials together in minutes.

E-6000 remains relatively flexible even after it has fully cured.

It is chemical and wear resistant.

E-6000 Challenges

However, there are also some disadvantages when working with E-6000. Here are the glue challenges you should know:

E-6000 produces noxious fumes when working. For your own safety, be sure to wear a respirator and/or work in a well-ventilated area or outdoors.

E-6000 takes much longer than many adhesives to fully cure. For smaller applications a full cure can take 8-12 hours but for larger projects it can take up to 48 hours. But after that, you shouldn’t have to worry about your parts falling apart. So if you have the time, the wait may be worth it.

E-6000 can leave stringy bits, similar to hot glue.

While E-6000 is similar in strength to contact cement, it is sold in much smaller tubes.

To reiterate, you CANNOT use E-6000 on insulation foam. It will melt and eat away at the material, and it just generally won’t end well.

Safety with toxic adhesives

As with any adhesive, always know what you are working with and follow all directions and safety warnings on the packaging. Especially for E-6000 it is incredibly important to protect yourself when working with this adhesive. Like contact cement, E-6000 is a solvent-based adhesive that gives off toxic fumes when working. Aside from just giving off a strong, slightly unpleasant odor, these fumes are really noxious to inhale. Both short and long term exposure to E-6000 fumes can cause serious health problems so please do not ignore the warnings on the bottle. For your own protection, always work with a respirator and/or in a well-ventilated area or outdoors. Your health and safety are more important than any cosplay.

IN THIS ARTICLE

If you plan to test your artistic skills on a foam board or use the board in the office or at home, be careful about the glue you use. Because the wrong glue can be a waste of time, money, materials, or all three. That’s why we’ve compiled a list of the best adhesives for rigid foam boards here. This list was made because hot glue, wood glue, spray, and construction adhesives work best for these lightweight yet strong boards. Therefore, the selection of the appropriate foam adhesive forms is the basis for creating something artistic and spectacular with the help of these panels.

The 7 Best Adhesives for Foam Boards

The classic Elmer Extra Strong Glue Stick comes in a pack of four and can be used by the whole family. Ideal for any task around the home or office, the glue stick works great on foam board, cardboard, envelopes, computer paper, scoreboards and more. It is especially good for attaching labels, charts and pictures to your foam sheets. Elmer’s E5010 Glue Sticks create a secure seal and a little goes a long way. The washable formula is easily removed by hand.

advantages

non-toxic

Super smooth

Photo-safe formula

acid free

Dries fast

Disadvantages

Small

Aleene’s quick-drying tacky glue is one of the best foam board adhesives because of its versatility and durability. It only takes 35 minutes to dry compared to traditional adhesives which take more than an hour. The 3-pack multi-purpose adhesive is great for crafts, small repairs and more and works well on foam board, paper, metal and wood. In addition, the formula is easy to clean from surfaces.

advantages

Can be used on multiple materials

Continuous

Easy to clean

super strong

non-toxic

Odorless

Disadvantages

Cannot dry clear

This engineering adhesive from Bob Smith Industries is a silicone based formula that works well with EPP and EPO foams. It’s also compatible with plastic, wood, cardboard and more. The glue needs about 10-12 hours to stick with full strength.

advantages

Fast stapling

Clear conclusion

Foam friendly

Strong bond

Good consistency

Disadvantages

May take some time to stick

Loctite PL 300 Foam Board Structural Adhesive is thick and tacky and does its job decently. The formula is based on water latex that bonds foam boards to itself or other surfaces. It also adheres to vinyl vapor barriers. It is one of the best foam board adhesives that can be used both indoors and outdoors and is also good for bridging small gaps. This adhesive is also effective on brick, concrete, metal and wood. This video gives you more insight into the product.

advantages

Versatile

Fills small gaps

No burn through

Works in all weather conditions

Easy to apply with a caulking gun

Disadvantages

Can not be quick drying

Beacon Hold The Foam Adhesive is designed to bond all types of foam including styrofoam, fabric, beads, cardboard, paper and more. The non-flammable formula is safe to use and easy to clean, and the thickened formula reduces weight after drying.

advantages

Washable

Non-toxic

Bonds most materials

Fast drying

Disadvantages

May take some time to stick firmly

Uhu Magic Blue Stick is a multipurpose pack of 12 sticks with a screw cap to keep the glue safe and protected without drying out. It tarnishes blue when applied, but dries clear in color. The adhesive is designed to create a long lasting bond with just one swipe.

advantages

Easy to wash

Solvent free

Easy to use

acid free

non-toxic

Disadvantages

Can have a wet consistency

This mini pack of six tubes is a perfect solution for permanently bonding all types of foam including EVA, EPP and Styrofoam. It also works well on Depron, Lexon, carbon fiber and balsa wood. Each 5mm tube runs smoothly on the product and holds tight without becoming hard and brittle.

advantages

Residue free

Strong formula

multipurpose use

Dries clear

Even coverage

Disadvantages

One time use only

How to choose the right glue for foam board?

Here are a few suggestions to help you choose the right foam board adhesive.

Fast Drying: Look for adhesives that don’t take too long to dry. Fast-drying adhesives help you get the job done faster.

Safety: Make sure the glue is non-toxic and easy to clean.

Size: Consider the size of the glue stick or tube. Larger ones will help you work on large projects, while smaller ones can be more convenient since you don’t have to worry about drying.

Creating artwork with foam board becomes a lot easier when you have the best foam board adhesives. Whether you are using a foam board for office use or improving your artistic skills, you can choose any of the above options as they are listed after thorough research. However, make sure you choose one that sticks and dries faster, is non-toxic, odorless, and durable. Also consider factors such as the size of the project and ease of cleaning before purchasing.

Why trust MomJunction?

Wedetso Chirhah writes well-researched articles on electronics, cars and household items. He has compiled this list of the best foam board adhesives after researching existing user reviews to offer you an unbiased opinion. He’s also put together a buying guide detailing the pros and cons of each product to help you make an informed decision based on your needs.

Featured Articles

Was this information helpful?

Many craft projects may require gluing the plastic and foam together. Unfortunately, some plastics cannot be glued at all. For those that can, look for an adhesive that can bond porous and non-porous surfaces. Most adhesives list the types of materials they can bond. While some adhesives list both plastic and foam as materials they can bond, remember that most products also come with a disclaimer that not all plastics can be bonded.

Adhesives for plastic and foam

According to the label on Elmer’s Craft Bond All Purpose Glue, this product can bond both porous and non-porous materials. It specifically lists foam. Stronger adhesives for bonding plastic to foam include Liquid Nails, Gorilla Glue and E 6000. E 6000 claims to be an industrial grade adhesive that is flexible and can be painted. It can stick to most plastics and many other surfaces. Liquid Nails makes three products that they say can bond plastic to foam. One of these is the Liquid Nails Home Projects Repair Adhesive, which is acid-free and cures within an hour. The company also makes Liquid Nails Clear Small Projects Silicone Adhesive, which takes six hours to cure. The site also recommends the Liquid Nails Adhesive Variety Pack. Gorilla Glue makes two adhesives suitable for bonding plastic to foam, according to its website: the basic Gorilla Glue and the new Gorilla Epoxy. According to the company’s glue guide, both adhesives can bond plastic and foam. Both glue almost everything except paper and rubber.

Gluing wood and foam together can be extremely difficult. The absorbent nature of the foam makes gluing difficult, and some adhesives can even melt the foam. But as long as you have the right product—in this case, polyurethane structural adhesive—gluing foam to wood is easy.

step 4

Use foam craft glue for projects that need more durability. Craft glue is available at craft stores and is similar to white paper glue, but is more runny and sticky. It works on foam, wood, fabrics and plastics. Spread the craft glue sparingly on both surfaces you want to glue together and let sit for at least two minutes to allow the glue to become tacky, then press them together for another five to 10 minutes. Don’t use too much glue or it will soak into the foam and make it stiff.