Best Grip For Sweaty Hands? Trust The Answer

This is how you can tell if your golf grips are worn out

Is it time to change your grips?

Your grips are the only piece of equipment you’ll touch on every single swing, so it’s crucial that they’re always at their best.

Like your golf shoes, grips wear out over time due to a number of factors including:

sweat & oils from your hands

dirt

UV rays

Hot and cold conditions

When your grips are worn, they feel slippery and lose traction. Standing over that tight tee shot or approaching across water without knowing if the club will stay in your hands is not ideal.

As a general rule, it is recommended that you change your grips once a year. However, if you play more than 40 rounds a year, or hit the range a few times a week, you may need to replace grips more frequently.

Knowing what to look for can make it relatively easy to determine if your grips are worn and need replacing. Here are some ways to say it:

1 SMOOTH HANDLES The most obvious sign of worn handles is a smooth, shiny feel and appearance. You may also find that your grips feel tighter than they should be. 2 WEARED OR MISSING GRIP COSMETICS When playing grips such as the MCC or MCC Plus4 that have white, blue, gray, red or any other colored fill, a clear indication of grip wear is when that color begins to fade or discolour. 3 RUBBER OR CABLE CRIPPING If you notice that the rubber or cord in your golf grips is beginning to crumble, you’re overdue for a grip change. Golfers often notice extreme wear where their thumbs are placed on the top half of the grip.

Fresh grips can make a huge difference in your confidence and performance in all conditions. Stand over every shot knowing you will give your all and do your best.

Our handy grip selection tool will help you decide on your next set of grips, from size to performance characteristics.

How to clean golf grips

Cleaning golf club grips is an important task that must be performed by all golfers to ensure consistent and accurate shots with their golf clubs. If you ask any professional golfer, they will tell you that the grip is just as important as any other part of a golf club.

It is important to maintain golf club grip in order to be able to hold your golf club firmly. A good and clean golf club grip helps keep the hand stable and ensures the golfer can use a light pressure grip.

Golf club cleaning will make your grip feel like new every time you use your golf club after cleaning. Another important reason for golf club cleaning is the development of the colors of the golf club grips. In the past, grips could be easily groomed with a traditional black tint to hide imperfections and wear.

However, the recent trend towards glowing grips has made it more important than ever to clean your grips regularly. This is because environmental particles, grease, oil, and sunscreen are more visible from your hand on a vibrant handle.

The negative effects of a dirty grip must be combated by golfers. Grips can be cleaned using a variety of methods, from using a simple bucket of soapy water to making the most of the equipment found on driving ranges.

Steps to clean a golf club grip:

To begin cleaning a golf club grip, you must first clean the entire club. It is recommended to use a plastic bucket filled with water first. A kitchen or bathroom sink also does this job fairly well.

Next, you’ll need laundry detergent, warm water (slightly warmed), any type of plastic-bristle brush, and an old cloth or towel.

First clean the golf club:

Fill the plastic bucket with lukewarm water. The water level should be filled enough to allow the heads of the iron to be submerged without the water spilling over the ferrules. Now add some detergent to the water. Make sure the water is slightly warm and not too hot as it will loosen the ferrules. Place the bucket of golf clubs in the warm water. Keep the grips soaked until the grease and excess dirt comes out of the grooves. After soaking the grooved golf club for a few minutes, clean it with a plastic bristle brush such as a brush. B. a toothbrush. This step is important to remove dirt from the grooves. This helps increase the contact area between the golf club and the ball at the time of impact. After cleaning the grooves, clean the back of the clubhead and sole of the iron to remove any grass, sand or mud. After removing the mud, rinse the clubhead with clean water. Dry the club head with the old towel and run the towel down the shaft to ensure it is completely dry before putting it back in the bag. You can also dry the handles with an air dryer, but the towel is a better option as it ensures no residue is left behind.

The best way to clean golf grips

Golf grips can be cleaned using methods other than the standard bucket and cleaning solution method.

One of the best ways to clean golf grips is by using grip cleaning wipes, which are available on the market for around $5.99.

In one simple step you can easily clean the grip of golf clubs with the golf club cleaning wipes.

First remove the wipes from the pack and then reseal the pack for future use. Take the towel and run it over the golf grips.

Two golf towels are enough to clean the entire set of golf clubs, priced at 80 cents. Because you don’t need to keep the golf clubs soaked or dried, the wipe method is quicker and easier to perform than the water and bucket method.

In the summer heat, golf club grips can become gritty after a few rounds. To keep the racquets in good condition, spray some water on the handles with a spray bottle. Spray the racquet 3-4 times so that the handles are wet enough. If wet, dry the handles with a towel.

When you’re ready to give the handles a deep clean after soaking them in lukewarm water, spray some household cleaner on the handles. The cleaner dissolves grease and oil between the handles and leaves them looking as good as new. However, it is important to rinse the handles with water after using the household cleaner. The cleaner may contain ammonia which can dry out the handles and cause damage.

You can use a microfiber golf towel specifically designed for cleaning golf club grips. To give your golf club grips a nice finish after the cleaning steps, you can use metal, steel or chrome polish (depending on the club) to give the club a nice finish.

What to use to clean golf grips?

The requirements for cleaning golf club grips vary depending on the cleaning method. You can either invest money in cleaning kits or go for a DIY approach using household materials.

Water is the most basic component for cleaning equipment. For best results, lukewarm water is recommended when cleaning golf club grips.

Water that is too hot can cause the ferrules to loosen. This can cause the ferrules to slip down the shaft. Likewise, cold water will not be effective at removing dirt.

A bucket can be used to prepare the soap mixture and then soak the club heads in it.

Detergent is important to remove stubborn stains. Liquid soap is recommended as it makes the cleaning process much easier. Do not use bleach or heavy agents as they may affect the color and texture of the handle.

A plastic brush with bristles allows easy cleaning of the grooves of the club head. It is recommended to use a soft bristle brush to keep the texture undamaged.

A sponge will help hold enough water to clean the entire racquet without wasting too much water or soap.

When should golf grips be cleaned?

Golfers should clean their golf clubs once or twice a year. However, if you play golf frequently, the grips should be cleaned once a month. Oils and sweat from hands, dirt, temperature changes and other factors can contribute to grip wear.

The worn grips are harder to play than when they were used for the first time and the rackets lose their original stickiness due to the deposits. This increases grip pressure and makes it difficult for the golfer to get proper wrist release.

Grips with little to no tack are likely to have a major impact on the squareness of the clubhead at even the slightest amount of slippage, and affect the golfer’s performance. To prolong grip life, golfers should clean the grips several times each season to remove excess oil or dirt built up through frequent use.

How Often Should You Clean Golf Grips?

Golfers who use their golf clubs regularly should wash the grips at least once a month. The amount of accumulated dirt and grease is likely to increase if the handles are not washed regularly and properly. This can affect the golfer’s grip due to accumulation on the golf club.

Regular cleaning of golf club grips increases their longevity and makes them look like new. It is also preferable to regularly clean the clubheads after each round. Clean grips on golf clubs make a world of difference, especially in the summer, as oils and sweat transfer from your hand to the grip and take away the soft, sticky feel.

However, the golf club should not be cleaned excessively with soapy water as the grips can become slippery and sticky. To bring out some stickiness, you can scrub the handle with a coarse piece of sandpaper. If you keep the clubheads in the car or garage, they will harden faster due to the warm temperature; Therefore, the clubs should be kept in a cool place.

How to make golf grips sticky again

Golf grips can be made tacky again by regular cleaning and then sanding. Cleaning the handles ensures that no dirt or debris is left on the handles.

There are two simple steps to easily cleaning the grips, including soaking the golf club drips in lukewarm water mixed with liquid detergent, then wiping with a towel.

If the cleaning methods do not help to regain the stickiness of the golf clubs, it is better to replace them due to the low stickiness and the golfer might find it difficult to hit straight and accurate shots. Grinding the grips is an important step if you want to ensure the golf club grips are sticky. Grinding can be done with the following steps:

Use medium-grit sandpaper to rub against the handle. Before moving to coarse grit sandpaper, it is better to check with medium grit sandpaper first. This would ensure that the handle would not be damaged by the rough surface of the sandpaper.

Using a light hand, rub the sandpaper over the handle in up and down motions. This would help roughen the grip. Don’t rub the handle with a hard hand as you could end up sanding the handles down instead of making them sticky.

Use a towel to remove excess sandpaper dust and loose grip material from the golf club grip.

With these three steps, your golf club grip will be sticky as before. Depending on the frequency of use, it is advisable to clean and sand the handles at least once a month. You can also replace the grips in a year or two if your golf club is used regularly.

How to make leather golf grips tacky

To restore the stickiness of a leather golf club grip, you can use castor oil. It helps in restoring the stickiness of the golf grips easily. Applying a small amount, like 2-3 drops, will do the job pretty well. Vegetable oil can also be used to serve the same purpose. It works quite well, but if your hands sweat, the handles can easily go rancid.

If you’ve ever restored an old softball or baseball, you can get a bandage that can be used to make the golf grips sticky. You can also easily find it in a sporting goods store. You can also use a small prong for this.

Best sticky spray for golf grips

3M™ Super 77™ is a multipurpose pressure-sensitive adhesive spray that can be used as an adhesive for a variety of lightweight objects. It can be used to increase the stickiness of golf club grips. If you’re looking for less messy options, you can opt for bleach white and spray it on the handles.

The golfer can use a wet green Scotch-Brite pad to scrub the grips as that also works quite well. The sticky spray can make the golf club grip sticky if overused. For a safer option, pine tar can be used as an alternative to golf grip glue spray.

Do white golf grips get dirty?

Yes, white golf grips get dirty. White golf grips are less likely to turn brown or dirty if they are well cared for and cleaned regularly. If you rarely use the golf clubs, the white golf club grips do not need to be washed and cleaned regularly.

The white grips can become dirty and stained with regular use of the golf club. You can clean the handles with bleach. Some brands make white rubber grips that are stain-resistant; Therefore, they can last all year round without getting stains or smudges.

How to clean a white golf grip

How easy it is to clean white golf grips depends on how regularly they are used. Depending on the manufacturer, if the golfer uses it regularly, the marks can be stubborn and difficult to remove. However, if the golf club is used twice a week, the grips can be easily cleaned using the traditional soap and water method.

How to clean golf grips with Windex

Windex combined with rubbing alcohol cleans golf club grips well. It is ideal for use in the summer, when golfers’ hands are more likely to sweat. Windex helps keep the grip tight.

How to clean golf grips with sandpaper

Sandpaper is a good way to temporarily fix worn golf clubs.

First wash the dirty grips with lukewarm water and soap to remove all dirt and excess debris from the grip.

After drying the handle with a towel, use sandpaper to roughen the handle.

You can use coarse sandpaper, but be careful not to rub the paper too hard. This method works ideally for cable glands.

How to clean Golf Pride grips

The golf pride grips are made of rubber, therefore the use of bleach may damage the grips; hence it should be avoided.

Easy Method to Clean Golf Pride Grips:

All you have to do is soak the grips in lukewarm water with detergent mixed in. After some soaking, rinse the handles and towel dry. You can use mild dishwashing detergent or any other mild detergent as a cleaning agent.

How to restore old leather golf grips

Lexon can be used to clean and restore old leather golf grips. Not only does it clean them, but it also helps soften the leather grips, making it easier for the golfer to keep a firm grip on the club. Lexon can easily be purchased at any leather or sporting goods store. Castor or vegetable oil can also be used to serve the same purpose.

How to fix slippery golf grips

For cleaning and restoring golf club grips, soap and water can do the job fairly well. However, it is said that when the golf club grip becomes shiny and slippery, it is better to replace them.

200 grit sandpaper can be used to reduce the slipperiness of a golf grip as it removes the surface layer. It requires a lot of work, so replacing the golf club grip is a better option.

Further Reading: How to Regrip Golf Clubs

Yes, I would like to subscribe to the Golf Pride e-newsletter to receive updates on grip testing opportunities, special offers on limited edition products, exclusive giveaways, grip tips and more.

Yes, I would like to subscribe to the Golf Pride e-newsletter to receive updates on grip testing opportunities, special offers on limited edition products, exclusive giveaways, grip tips and more. I agree to be informed regularly. I understand and agree that Golf Pride or its parent company Eaton will use my information to personalize marketing communications. I agree that the personal information I have provided may be shared with Eaton Corporation plc in Ireland, Eaton Corporation in the United States of America and for storage in electronic marketing databases hosted in Canada. Any use of my personal information will be in accordance with the relevant and applicable data protection laws and the Eaton Privacy Policy. I can withdraw my consent to receive marketing communications at any time by contacting Golf Pride.

Putting new grips on your clubs is like getting a new pair of shoes or a new car.

The new grips feel great in your hands, they’re easier to get a proper grip on and certainly feel like they’re helping your game.

The problem is that new golf grips don’t feel new for very long.

However, there are ways to prolong that sticky feeling in your grips.

In this guide, we’ll talk about how to make your golf grips sticky again, what you can do to keep them sticky, and when you know it’s time to swap out your grips.

Necessary accessory for cleaning golf grips

Let’s start by gathering the supplies you will need to clean your golf grips.

First you need a large bucket; A five-gallon bucket works best if you have access to one.

You will also need some dish soap, water, a scrubbing brush and a towel.

Once you’ve gathered all your supplies, you can move on to the next step.

Steps to cleaning golf grips

Step one

Fill your five-gallon bucket about half full with a mixture of soap and water.

Although the temperature of the water doesn’t make a big difference, it’s best to use lukewarm water.

Take all the golf clubs out of your bag and place them in the bucket, handle end down.

You may have to lean the bucket against a wall as it tends to tip over once all the racquets are in the bucket.

Let your clubs soak in the bucket for about five minutes.

step two

Next, you should grab your scrub brush (one with plastic bristles works well, steel might snap on the handles).

Hold the club firmly in one hand and use the other hand to scrub the golf club grip.

Make sure you get the entire grip, but the worst areas are right in the middle of the grip where your hands are most of the time.

Also clean the back end of the racquet, sand and dirt can get into these areas.

If you have to dip the racquet in the water-soap mixture to rinse it off while scrubbing, that’s fine.

You will most likely see a lot of dirt and grime coming off the clubs.

This is perfectly normal and you are not destroying the handles.

step three

Once you have scrubbed all of the handles, you should rinse them off with clean water.

You can empty your original bucket and fill it with just water, or you can just spray the clubs with a hose.

step four

After the handles have been scrubbed and rinsed, they need to dry.

You can just leave them to dry on their own, but we recommend towel drying them at least a little.

Clean the standing water off the handles, then lay them outside to dry.

When the handles are dry they should be a lot stickier than before.

The washing process is quick and easy and can add quite a bit to the life of your grips.

Don’t put your golf clubs in your golf bag to dry.

When they are completely dry you can put them back in your bag.

Why Do Golf Grips Get Slippery?

Golf grips become slippery because dirt, grease and oil get stuck.

When your hands touch the golf club during your round, they aren’t always clean.

You most likely have sunscreen on your hands.

Maybe you had a bite of one of those hot dogs at the turn?

Or maybe you sweat a little because it’s a hot day.

Regardless of what you do to maintain your grips throughout a round, your hands will get dirty.

How can I extend the life of my golf grips?

There are several things you can do to extend the life of your golf grips.

Many golfers care about the heads and shafts of their clubs, but it’s also important to take care of your grips.

While this isn’t the most expensive part of your club, there’s no reason to replace them if you can get them running for a long period of time.

An important way to extend the life of your grip is to wash your hands after applying sunscreen.

Most golfers are familiar with this problem.

You run to the first tee, quickly put on some sunscreen, grab your golf ball and a tee and head to the tee box.

Granted, you were smart about wearing sunscreen.

This is a step you don’t want to skip; However, we think you should change up your routine a bit.

Apply sunscreen in the bathroom of your house.

When you get up in the morning, put on the sunscreen and then wash your hands.

By simply changing this process, you could see your grips last months or even years longer.

When sunscreen gets on your hands it gets absorbed, builds up and makes them very slippery.

Another great exercise to start applying is a quick wipe down with a towel before each shot.

If you have a towel hanging from your golf bag, wipe your hands with it before grabbing the club.

This won’t keep your grips perfect, but will leave a little sweat or dirt on the towel and not your racquet.

Finally, you want to implement the handle washing process discussed above.

This is not a complicated process and it is worth doing about once a month.

Another good time for a clean grip is after a good training session at the shooting range.

If you’ve spent a few hours hitting golf balls, your grips are probably pretty dirty and could use a good cleaning.

What happens when golf grips become too slippery?

Aside from the fact that you might find it a nuisance, you’re probably wondering why keeping golf grips sticky is so important.

As soon as a golfer feels his grips are slippery, he immediately increases grip pressure.

Increased grip pressure is terrible for a number of reasons.

First of all, increasing grip pressure also increases tension in your forearms and shoulders.

This tension will make it harder to get your routine swing working as it should.

The increased grip pressure also makes it very difficult for you to get the right feel for your swing.

When your hands feel like they’re clenched on the racquet, your swing is developing into a manageable swing.

These types of swings are difficult to repeat, and they don’t involve the larger muscles that help you create a reliable and consistent golf swing.

If your hands grip the golf club too tightly, you will also find it difficult to let go of the golf club.

Releasing the golf club allows you to stop clipping the ball and keep the clubface straight at impact.

It might seem like a bit of an exaggeration that a slippery grip could cause all of these problems, but it’s undoubtedly the truth.

Golfers on the pro tours pay great attention to grip pressure and clean hands and grips.

You’ll notice how often they wipe their hands, and their caddies make sure the holds are always in tip-top condition.

You have to remember that the grip of your golf club is the only connection you have with the club.

If you want your swing to be perfect, the connection between you and the racquet must also be excellent.

How often should I replace my golf grips?

How often you should replace your golf grips depends entirely on how much you play.

If you play golf every day of the year, you probably need new grips every six months.

If you play a lot of golf, you probably need a grip change once a year.

If you play once a year, you might not need to replace your grips until they start rotting off your racquet!

Knowing when to change grips is not very difficult.

You will be able to see them deteriorate in certain areas.

First, follow our cleaning process outlined above.

If you’re getting this right and feel like your grips haven’t improved, it may be time to re-grip.

A trick some players use is that they take sandpaper and try to roughen up their grips a bit.

When washing and sanding don’t work, it’s surely time for a new set of grips.

Your local PGA Professional can tell you if it’s time to replace your grips.

You should listen to their suggestions on the latest and greatest grips on the market.

Golf grip technology changes quite often, and if it’s been a few years since you changed your grips, you might be surprised at the new options.

Are there certain holds that work better for people who like sticky holds?

Some golf grips are intended for players who like a very rough and sticky feel.

If you like a grip that feels like it’s sticking to your hands, there are some from WINN under the Dri Tac brand.

These grips have an almost sticky feel and this has become very popular with some players.

Another good option if you want a grip that won’t fly out is a cord or semi-cord grip.

A string handle runs through a string and they are very rough to the touch.

If you’re worried about blisters on your hands, the drawstring isn’t for you.

Many pros play with the cord or half cord because they feel the golf club will stay securely in place.

Golf Pride has developed a range of grips called Multi Compound.

These handles are a bit of a cord only in the places you need them.

If you play golf in wet weather or want something that feels firm in your hands, this is a good choice.

Final Thoughts

A golf grip needs to feel tacky, not only so you know it’s clean, but so your game can play at its best.

Cleaning your golf grips is not a long or complicated process and you should do it while cleaning your golf bag.

If the average handle is $10-$12 a piece and you can extend the life another six months to a year, that’s a big savings.

How to Clean Your Golf Clubs and Grips – Ultimate Guide

People don’t really like cleaning. This also applies to golf clubs, apart from those that are thoroughly committed to cleanliness.

When you’ve just washed the dishes, done the laundry, and washed the car, the last thing on your mind is that your golf clubs are dirty.

Golf clubs are often neglected when it comes to cleaning, but you shouldn’t let that happen. Clean golf clubs can have a significant impact on your game. Best practice is to do a quick clean right after your round and a more thorough clean as soon as you get home.

Impact on performance

In all my years in the golf business, there have been numerous times that a golfer has complained about not being able to get spin, only to find it had to do with dirty golf clubs.

Yes, dirty clubs can have a huge impact on your golf shots. If you’re having trouble landing the ball on a green, you can make sure the grooves on your club are clean.

Not to mention the fact that if you’re spending thousands of dollars on new racquets, you really should take care of them!

Should you clean your clubs at all? How often?

A great golfer will tell you to clean your golf clubs after every shot and then again at the end of the round. A thorough cleaning of your clubs should also be done every few weeks. If you keep the dirt under control and clean your clubs often, doing your monthly cleaning will make things a lot easier.

We recommend wiping down your clubs thoroughly at the end of the round and cleaning the entire bag once a month.

What are the benefits of cleaning

The biggest benefit of cleaning your racquets is that the contact between the ball and the racquet becomes much better. The grooves on your golf club and the indentations on the ball must interact to get the right flight and reaction out of your shot.

When the grooves are caked with mud and you can’t get solid contact, it becomes very difficult to get the desired results from your golf shots. You can’t clean your golf ball in the middle of a golf hole. This would violate the rules of golf. Since you have the ability to clean your golf clubs, you should!

As well as the short-term benefit of keeping your racquets clean, it’s also important to ensure you take care of your racquets over the long term. Because golf clubs are so expensive, you want them to last for many years. As dirt and grit builds up on your racquet, it can affect finish and groove shape over time.

How to clean your irons and wedges

Now that you understand the importance of cleaning your golf clubs, let’s take a look at how to clean them properly. There are right and wrong ways to clean golf clubs.

Of all the clubs in your golf bag, the irons and wedges are the most difficult to clean. They have the most interaction with the lawn, so they get pretty dirty. Here are some steps to make sure your irons and wedges are very clean.

Fill a bucket with warm water and dish soap

Put all your irons in the bucket and let them soak for about ten minutes.

You should not leave the irons overnight as this is unnecessary and could cause rusting problems.

Clean with microfiber

Then pull the irons out of the bucket one by one and clean them with a microfiber cleaning cloth and a soft brush. Many brushes sold for irons are wire brushes, but if you use a good microfiber cloth to get into the grooves you shouldn’t need this.

Rinse after exfoliation

After scrubbing the irons, you should put them back in the bucket for rinsing.

Dry with a towel

Finally, pull out the irons and wedges and towel dry them completely before putting them back in your bag. It is important to dry the golf clubs so that they do not rust when left in your golf bag.

How to clean your driver

Your driver is probably made of titanium material, which makes it much more sensitive to scratches. When cleaning a driver, you need to be a little more careful than with irons and wedges.

When cleaning your irons, simply dip your driver’s head in a bucket of warm, soapy water. Use the same microfiber cloth to clean the driver, then rinse and dry as you would with an iron. There’s really no reason to scrub the driver with a brush as this also carries the risk of scratching the face or top.

Best substance for cleaning

The best substance for cleaning golf clubs is soap and water. Using the soap on the racquets is safe and helps the dirt come off easily. Some people have luck cleaning their golf clubs with vinegar and it can be a great solution.

If you see that golf club cleaner or Windex or bleach is recommended, you most likely won’t damage your clubs; There is simply no reason to use these substances. Soap and water will do the trick.

How to clean with WD40

You may have heard that WD40 can be an effective tool for cleaning your irons and wedges. Although WD40 can work quite well in certain situations, you have to be careful how you use it.

If you find your clubs have some rust, you can use WD40 to remove it. The great thing about WD 40 is that it can sometimes help prevent rusting in the future. Here are the steps to follow to use WD40 to clean your clubs.

Take the golf clubs out of the bag; If you spray WD40 on your bag, it will smell for a long time.

Spray the WD40 on your irons and wedges and let it sit for a few minutes. Take a dry cloth and wipe the WD40 off the clubs. Once it’s off, you can wash and rinse the rackets.

You should not leave excess WD40 on the golf club as this can cause the face to behave differently.

Can you clean golf clubs with coke?

If you haven’t heard, cola can have some super cleaning abilities. If only it were as good for our bodies as some dirty golf clubs! You can fill a bucket with a 2 liter bottle of Coke, put your irons and wedges in and come out with some really sparkling clubs.

Coke is good for breaking down the dirt and grime that may be on your clubs. However, it also has quite a bit of sugar in it. Leaving it on your golf clubs without rinsing and cleaning can leave you with a sticky mess.

Coke has also been touted as an effective way to remove rust stains from your golf clubs.

As long as you rinse the golf clubs out after soaking in the coke, you shouldn’t have any long-term problems.

Can you clean golf clubs with vinegar?

Vinegar is an all natural cleaner. You can use it to clean rackets, remove rust and it is also very useful in the kitchen. Cleaning your golf clubs with vinegar eliminates the need to soak them in pure vinegar. Just add a few tablespoons to a bucket of water and you’ll reap the benefits.

If you notice the beginnings of rust on your golf clubs, vinegar is a great way to get rid of it as well. When the situation seems pretty bad, making a paste out of vinegar and baking soda and letting it sit on your club for a few minutes can really change the look of golf clubs.

People are often surprised at how great vinegar is when it comes to polishing clubs. You’ll notice that they have a little sheen when they come out of the bucket of vinegar.

How to clean your golf club grips

When you thoroughly clean your racquets, don’t forget the grips. It is very important to keep your golf club grips clean. Remember, your only connection to the racquet is the grip. If the grip is not in good condition, you can end up hitting some pretty bad golf shots.

When cleaning the handle of your racquets, you don’t want to soak the entire handle in the bucket of water. There’s no reason for that, and it just takes a very long time to dry. Instead, take a plastic bristle brush or a special grip brush and use some soap and water on your grips.

Use this brush to scrub dirt, oil and grease from the handle. You’ll be amazed at how much black liquid runs off your handles as you scrub. The best part about washing your grips is that they get a lot stickier afterwards.

Don’t put your wet golf grips back in your bag until they’re dry. Let them dry outside for some time. Do not place them in direct sunlight while drying as this could damage part of the rubber that makes up the handles.

When cleaning the face and grooves, don’t skip the grips!

Is there a golf club cleaning service?

Generally, after a round of golf, you will see a golf dealer waiting to clean your clubs. If you notice it, use a wet towel to clean the racquets. This is because this towel is generally very effective.

While this is a great service and certainly helps keep your clubs clean, we still recommend completing the monthly deep club cleaning. When you do the deep cleaning, you also have the option to clean the grips of your racquets.

In fact, while you’re at it, you might as well clean your golf shoes; it must have been a while!

How to remove scratches from golf clubs

Sometimes, after cleaning your golf clubs, you will find that they have some scratches. This is unfortunate and sometimes not much can be done.

If the scratch or mark is on the top of your driver, you can paint over the scratch with golf club paint and clean it up a bit.

If the scratch is on the face of your irons or wedges, it could affect game play. You can take your racquet to a local repair shop and have them see if the scratch is deep enough to affect the racquet’s play.

A very light scratch in a racquet is unlikely to have much of an impact. Always leave your clubheads on your driver and fairway woods to avoid damaging them.

Conclusion – Why cleaning clubs is important

As you can see, cleaning your golf clubs is an essential part of being a great golfer. If you don’t clean your clubs, you will struggle to make meaningful contact with the ball. Golf as a sport is tough enough. You don’t need a patch of mud or dirt holding you back from your next best golf shot.

Always be careful what cleaning solutions you use on your racquets. Using something corrosive might do some damage, especially if you have golf clubs with a special coating.

Fowler’s bag is perhaps the most interesting of the bunch. Not only does he have new irons in the prototype MB, they’re copper-colored and feature soft-stepping shafts (soft-stepping changes a shaft’s flex profile by taking the shaft for one club and plugging it into another, e.g. a 6 iron shaft in a 7 iron). The irons also have a parallel hosel so there is no offset. Stamped on the back of the racquet is RF on one side and REV 33 on the other, the number representing the 33 revisions that were made to dial in the design to Rickie’s liking. The design was more than a year in the making. Rickie replaced his 5-wood with an additional 5-iron, meaning he will be playing one in the traditional Cobra F9 Speedback model and another as part of his prototype set.

3 basic types of golf grips

Getting the right golf grip for your game is just one of the many aspects that must come together to help you become the best golfer you can be. A good golf grip helps with ball control and flight. Adjusting your grip can correct mistakes in your swing that cause you to clip or hook the ball. Here are a few sample holds to get you started. If you already play golf regularly with a solid grip, this will be a good reminder and bring you back to some of the basics that can often be overlooked by even the most experienced golfer.

There are three basic types of golf grips: vardon/overlapping, interlocking, and ten-finger grips.

Vardon or overlapping grip

If you are a beginner golfer, this is probably the first golf grip you will learn. It was popularized by Harry Vardon. Used by players with large, strong hands, this grip brings both hands closer together at the grip. After placing your hands on the racquet, take the pinky of your back hand and place it between your index and middle fingers on the dominant hand (for a right-handed player, the dominant hand is the left hand).

locking handle

Many leading professional golfers, such as Tiger Woods, use the locking grip. Place your hands on the golf club and interlace your pinky of the back hand with the index finger of the leading hand. This is a good grip for those with smaller hands. This grip allows you more control of the racquet because your hands are connected. It also doesn’t require a lot of forced pressure on the hands when locking with the racquet handle. So if you have weak hands, you’ll find that it takes little effort to hold on.

Ten finger grip

For this grip, you want to press the pinky of the trailing hand against the index finger of the leading hand. Then use the lifeline of the trailing hand to cover the thumb of the leading hand. This grip is not the most popular, but works well for many golfers. Beginners, seniors, and women should try this hold to see if it allows for more power and distance.

Choosing the best golf grip for you

Whether you’re just starting out or making it big, you should always work on perfecting your golf grip. Think of your racket as another part of your body. Do you want that limb to be in shape and well adjusted?

Think about it and focus on it – you will have more control and your game will show the improvements we all strive for.

Check out our YouTube channel for more golf tips!

If you’re really serious about improving your game and working in the golf industry, download our free golf career guide to explore all your options.

Contact us today!

With his one-length golf clubs and baseball bat-like grips, Bryson DeChambeau has always done things drastically different than his professional peers on the PGA TOUR. Of course, it was never without speculation from observers, but four PGA TOUR victories in 2018 alone seem to have put a stamp on DeChambeau’s unique tactics. However, DeChambeau, whose best finish of 2019 was 7th place at the Sony Open in Hawaii in January, continues to strive for perfection in his golf game and equipment. Sometimes that means going to extremes or, in this case, sloping slightly back to the norm.

After a 14-hour range session in Dallas the week leading up to the Masters, Dechambeau trimmed his oversized JumboMax grip weights in his Cobra racquets by 75 grams. His new grips, made from a different lightweight compound, now weigh just a little more than 50 grams, which is considered “normal” weight by industry standards despite their relatively massive size. He also switched from True Temper Dynamic Gold X7 shafts – extremely heavy and stiff iron shafts – to Dynamic Gold Tour Issue S400 shafts, which flex more than his previous gamer shafts.

Since joining TOUR, DeChambeau has been using JumboMax grips on his racquets, which weigh in at approximately 125 grams per grip. He’s now working on his gear with Cobra’s TOUR Operations Manager Ben Schomin, who says DeChambeau has improved his wedge game since he first appeared on the TOUR, but lately DeChambeau has struggled to maintain consistency with the flight of his to find wedges. The main problems were that the spin was inconsistent and they tended to fly too high. For his part, Shomin built him wedges that used beads of sweat on his heel to help close his face. While Shomin says it helped, DeChambeau – currently T105 on Strokes Gained: Around the Greens – wasn’t happy with his wedge play.

To see DeChambeau’s legacy wedges, click here.

Shomin and DeChambeau, seeking consistency with the wedges, decided to start testing different variables. As it turns out, DeChambeau liked the feel of a 50-gram grip compared to his old 125-gram grips, and the new construction allowed DeChambeau to fly the wedges lower and gain spin and launch consistency.

I’ve recently gone down a rabbit hole reading questions golfers have asked about the lead time to dry a new grip. Of course, this is the Internet, and opinions and experiences vary widely.

So in this post, I’ll shatter the doubts and explain how long you should wait after re-gripping golf clubs.

Additionally, I’ve provided tips to help you determine when your grips are dry and ways to speed up the process.

How long does it take before new golf grips can be used?

When using solvent or water based products, it takes an average of 2 to 24 hours for new golf grips to dry. However, as a rule of thumb, the longer you wait, the better.

Personally, I have never used new grips within 24 hours of installation. Lamkin suggests the time it takes to dehydrate their products is around 3 hours.

I’ve heard of people re-gripping golf clubs a few hours before going to the golf course. This is a risky step as you need ideal temperatures and high quality solvents.

Using inappropriate solvent or tape may increase drying time. Also, applying incorrect amounts can disrupt schedules.

The reality is that the time required will depend on your approach to installing the handles. For example, if you’re using an air compressor to get a grip on your grips, there’s no waiting around. Therefore, you can start swinging right away.

However, adding solvent to the handle takes an average of 3 hours before you can start playing. Conversely, using water-based products like soapy water can take up to 24 hours to dry completely.

Make sure to cover the top of your shaft with tape to keep liquid out. I’ve seen grips not dry at all due to liquid seeping into the shaft. The condensation reduced the effectiveness of the tape adhesive.

The bottom line is that an air compressor eliminates the need for drying. Solvent dries moderately fast, while aqueous solutions cause a slow process.

What can happen if you use your new golf clubs too soon after re-gripping?

Loose handles

In 2007 I played at the World School Golf Challenge in Christchurch, New Zealand. Before the 2nd round, a competitor from Australia broke my 3-wood when he forcibly removed his set of clubs from the cargo trailer. Long story short, I didn’t have a 3-wood, and since my driver was unpredictable, I needed it.

Anyway, the pro said he would do anything to have a new steel shaft and hold onto it until I reached the halfway house. The day didn’t go my way and it got worse. The grip wasn’t fully set, I took a swing and it felt like the racquet went further than any ball I hit that day.

Needless to say I left it in the clubhouse and used my 3 iron from every tee in 40 knot crosswinds. That was the least fun I’ve ever had on a golf course.

Uneven texture

Using your golf clubs before new grips have settled can result in an uneven texture. You may find more indentations in high contact areas, which can be uncomfortable and reduce traction over time.

Limited Control

Loose, wet grips make you lose all control of your clubs. You don’t have the traction you need between the grip and the shaft to optimize your swing speed and ball strike.

The racquet can move during your swing, causing it to close on impact. So you experience numerous hooks and a long day on the golf course.

Grab new

Playing with new grips before they’re dry can hinder the process and cause you to start over. If you have an air compressor, you can blow off the handles to reuse them. However, I suggest leaving the job to the professionals if you don’t have that equipment.

Without an air compressor, you’ll need a hook blade or utility knife to snip off the handles. Then buy a new set. Next, get out the rubbing alcohol and remove the old grip tape.

Now add the new tape for optimal adhesive. Finally, add an alternative or traditional grip solvent to prepare the shaft for the rubber.

I understand the thrill of doing it yourself, but installing or curing grips incorrectly is a costly endeavor. If you’re sure you can do it, go ahead. However, if you’re unsure what you did wrong the first time, save yourself the time and money and hire an expert.

This will tell you when your clubs are ready to use after re-gripping

No twisting

It doesn’t take a rocket scientist to determine when the grips are dry. The first step is to see if your grips are twisting. The first trick to knowing if your clubs are ready to play is to try spinning them.

If they are stable and not moving an inch, they are settled and ready for the connections. On the other hand, if they spin aggressively, they can still be wet. In this case, give them extra time to dry.

solid feeling

Next, run your palm over the back of the handle, making sure it’s firmly connected to the top of the stock.

The handle should not have any soft spots. In other words, you shouldn’t be able to pinch the grip and you shouldn’t feel a gap between the rubber and the grip tape.

Can you dry your new golf grips faster?

How quickly your grips will dry depends on the method you use to install them. Did you use conventional grip solvents, soap cleaners, or compressed air to install the grip? Let’s look at which methods achieve the fastest drying times.

air compressor

Using compressed air to install your grip completely eliminates drying time. This is the most effective method when you don’t have time to wait for the handles to set. Of course, not everyone has an air compressor lying around the house. However, if you do, take advantage of it.

Golf Magazine suggests obtaining a uniquely designed pressure tip from a golf equipment supplier to attach to your compressor. Insert the other end of the tip into the bottom end of the handle. This will inflate the rubber and you can slide it over the new tape.

Pulling the pressure tip out of the bottom of the handle deflates the rubber, making it stick firmly to the band. After that, the grip is ready for the course.

Solvent based approach

Applying solvent to the griptape is not as quick as using an air compressor, but is still ready to use after 2 to 3 hours. Golfers use denatured alcohol, paint thinner and lighter fluid.

I’ve never tried lighter fluid personally, but a few members at my local place have and they commend its performance. Some report being able to swing the clubs for as fast as 30 minutes to 1 hour.

In a demonstration of Lamkin grips, they suggest using mineral spirits, which they claim dries within 3 hours.

2 to 3 hours sounds like a lifetime compared to the instant gratification of the air compressor method. But it’s much quicker than the 24-hour average you have to wait when applying water-based solutions like dish soap.

Related: Before you think about installing new rubber, I recommend reading our guide to the 7 best golf grips for sweaty hands. These options dry quickly and are built to withstand warm and rainy conditions.

We’ll go over the 7 basic steps of tape and solvent re-gripping and discuss some common mistakes (warning!) that many beginners make here.

When choosing a grip, you should make sure that the core size of the grip is equal to (or very close to) the outside diameter of the shaft (FYI – also the first topic covered in our “Golf Grips: 6 Important Things You Need to Know” Article).

Installation of new golf grips requires the following materials/tools:

// STEP 1 – REMOVE OLD HANDLE

Removing the old handle may require the use of a hooked blade or knife. Remember to always cut away from yourself to avoid injury. Once you cut through the handle you should be able to pull the old handle off fairly easily.

When working with golf clubs, it helps tremendously to use a vise and shaft clamp to keep the club stable. While not necessary, a bench vise can help keep your workspace organized and clean. And since the racquet is held securely by the clamp, this can also help prevent injury. Vices are sold at most local hardware stores.

// STEP 2 – REMOVE OLD TAPE

After the old handle is completely removed, you should begin the fun (boring) step of removing the old tape. One player understandably asked if you could just stick the new tape onto the old tape (like you do with your DMV registration stickers). While this might seem like a sensible idea (to save some time), we still recommend removing ALL the old tape.

Common Mistakes Warning: Leaving old tape on can result in the new tape possibly not adhering properly to the old tape. It can create unwanted bulges in your grip. Most importantly, you end up with extra layers of tape increasing the diameter of the handle, which may not be what you want.

// STEP 3 – MEASURE THE NEW TAPE

With the handle and tape completely removed from the shaft, we can now prepare the new tape. If you are working with a roll of tape, pull out the tape and cut the length you need. In most cases, the length of the strap can be equal to the length of the handle. If you are using pre-cut strips of tape, you can skip to step 3.

Fyi – if the strip of tape is up to 1″ shorter than the grip itself, that’s fine. There’s still enough tape area to bond the grip to the stock.

// STEP 4 – PUT THE NEW TAPE ON THE SHAFT (BUT REMEMBER TO REMOVE THE WAX PAPER ON BOTH SIDES!)

We are now in full gripping mode!

With the new tape prepared and the wax backing removed, you should place the tape lengthwise down the shaft, but leave about 1/4″ to 1/2″ protruding from the bottom of the shaft

But wait!!! Both sides of the tape should be sticky. So you need to remove the wax paper backing from the tape. If you are working with precut strips of tape there will be wax paper on BOTH sides so remember to remove both!!

Common Mistakes Warning: This seems like an obvious step. But it’s worth noting because out of every 100 new handles there will ALWAYS be 1 or 2 times someone forgets to remove the wax backing of the double sided tape. Really tragic, because once mounted, the handles are unusable.

IMPORTANT: If you realized too late that you forgot to take off the wax backing, please DO NOT try to play golf with them or even swing your clubs. The handle could slip off the shaft and cause serious injury or injury.

Wrap the tape around the shaft. Then take the excess ribbon hanging from the end, twist it and insert it into the stock stump.

Plugging in the ribbon provides 3 things. First, it allows for proper sealing and adhesion at the bottom of the handle. Secondly, this prevents solvent from entering the shaft. Third (and most importantly) it prevents the grip from being cut/damaged by the sharp edge while sliding onto the shaft (during step 7).

Common Mistakes Warning: If you do not twist and insert the strap into the bottom of the shaft, you could cut through the grip material during installation, damaging the grip.

// STEP 5 – COAT THE INSIDE OF THE HANDLE WITH SOLVENT

Spray the stock liberally with grip solvent or mineral spirits, making sure all of the tape is covered and dampened. Then pour some extra solvent into the handle itself and hold your index finger on the handle’s cap to prevent solvent from escaping. Cover the opposite opening of the handle with the other hand and shake the solvent in the handle to fully coat the inside surface.

Uncover the grip cap and allow excess solvent to recoat the grip tape.

Common Mistakes Warning: Not using enough solvent makes it very difficult to slide the grip onto the shaft and can result in the grip getting stuck in the middle.

// STEP 6 – SLIDE THE HANDLE ON THE SHAFTS

This is where it can get tricky.

You should work quickly to avoid drying out solvents. Once you are done with step 5 you should open the grip jaws and slide it onto the shaft keeping it as straight as possible until the butt end reaches the end of the grip.

Once you’ve slid the entire grip onto the shaft, quickly adjust the grip as needed to achieve your desired final position (e.g. if you prefer the grip logo to be on the top or bottom).

Then take the club, turn it over and tap the end of the handle firmly on the ground to ensure it is fully seated on the shaft. Some excess solvent may drip out.

A few things to know about grip solvents:

First of all, solvent is needed as a lubricant, which allows you to slide the handle onto the shaft. If not enough solvent is applied inside the handle AND on the shaft, there is a high chance the handle will get stuck midway.

Second, solvent acts as a tape activator. This means that the tape’s tack will go into full contact mode after it dries. This will ensure the grip is securely attached to the stock.

Common error warnings:

During step 6, make sure to slide the grip onto the shaft as straight as possible. Sliding the handle open at even a very slight angle can cause the handle to break apart. This is especially true for wrap handles.

You will also rub off some of the solvent on the angled joint of the handle causing it to lose lubrication. This could result in your grip getting stuck in the middle, making it unusable.

Finally, many composite handles can be flimsy or delicate. Don’t assume they will stretch. Many of the softer grips, like Winn Excel or Dri-Tac, don’t leave much room for error. Again, if you don’t slide the handle straight, they can easily fall apart and get damaged.

// STEP 7 – WAIT 6 HOURS BEFORE PLAYING

It’s tempting to take out your racquets to play once the grips are on. However, we strongly recommend waiting at least 6 hours after grabbing again. The solvent must be fully cured and you should store the racquets in a dry and cool place during this time.

This is a general re-gripping instructional video provided by Lamkin that we recommend watching: