Chain Link Fence Boise Idaho? Best 66 Answer

You can install a chain link fence without concrete, but it’s not recommended.

Anchoring each fence post in concrete is the best way to ensure your fence will stand straight and tall for many years to come. It can be tempting to skip the time and expense of setting the pins in cement, but the savings aren’t usually worth it in the long run for a number of reasons.

soil composition

The type of ground you are setting fence posts in will help determine how stable the ground is and how much you can expect the posts to move over time. Much of the North Shore area has clay soil. Clay soil expands and contracts significantly between dry and rainy periods, allowing the stakes to shift and settle differently. Concrete anchors are a must in clay soils.

If you have particularly sandy soil, you can also succeed without concrete. You should use a polymer backing to improve stability and drainage around the post.

Installing a chain link fence with concrete

Whether you use concrete or not, installing a chain link fence itself requires several tools and materials, including fence posts, gates, chain link netting, fasteners, tension rods and wires, post hole digger, drill, hacksaw or pipe cutter, shovel, spirit level, masonry cord, plumb bob, Rubber mallet, socket wrench, pull rod, fence puller, pliers, premixed concrete, gravel and a trowel.

This method usually takes two full days, including the time the cement has to dry overnight.

Install chain link fence without concrete

If you decide to install your chain link fence without concrete, use a post hole digger to drill a hole deep enough to bury the posts at least two feet, or about 1/3 the height. Never drive the posts into the ground, especially if you have hard clay or rocky ground, or you will bend the tops. The hole should be slightly larger than the posts so you can fill it with soil packed tightly around the posts.

Installing your fence without concrete will save you a small amount of money on concrete, trowel, and gravel. You can potentially complete the installation in a day if you use the auger to dig your post holes. If you choose to save the drill bit rental fee (usually around $50 or so) it will take longer as you will have to dig the post holes by hand.

Anchoring fence posts with cement is the most secure

If you just need a temporary fence, concrete anchors aren’t really feasible. In all other cases, anchoring each post is the best way to prevent years of slipping and tilting. Some people suggest just using cement on the end, gate and corner posts, but this method can still allow for a lot of movement so you’ll be resetting the unanchored posts in a few years anyway.

Many homeowners choose to install their own chain link fence, but if you decide the job is too big or you just don’t want the hassle, the professionals at Patriot Fence Crafters can get the job done quickly and efficiently.

About Patriot Fence Crafters

When customers come to Patriot Fence Crafters with their residential or commercial fencing, they can always be assured that they are receiving the highest quality product and service, backed by an established reputation for customer satisfaction. We strive to provide every customer with a pleasant and successful experience at an affordable price. Call us today to learn more about our services and arrange a free estimate!

We proudly offer our complete fencing services throughout the greater Boston area including Georgetown, Beverly, Andover, Danvers, Ipswich, Lynn, Lynnfield, Marblehead, Manchester and nearby Massachusetts.

Share this: Facebook

Twitter

LinkedIn

Pinterest

More

E-mail

To press

Reddit

tumblr

pocket

Skype

Aside from enclosing your property, fences are an excellent way to improve the appearance of your home and increase its value. With quality materials and maintenance, a properly constructed fence can serve you for many years without the need for replacement or repair by a fence installer. The cost of installing a fence depends on various factors such as: B. length, height and material type. Longer and taller fences require more labor and materials to build compared to shorter and lower fences.

Although building a fence around your home can be expensive, you can combine hard work, research and creativity to discover the most durable and aesthetically pleasing fence within your financial means. The cheapest and most affordable fences result from cheap materials that require minimal maintenance and easy fence installation. The most common and cheapest types of fencing include naturally occurring, recycled, and manufactured materials that require the least amount of labor to install and maintain.

Aluminum fences

Aluminum is among the most attractive and simple types of fencing available on the market. While it doesn’t offer the security most homeowners demand, it’s relatively cheap in terms of maintenance costs. In addition, installing an aluminum fence requires maintenance during installation, during which you decorate and paint it.

wooden fences

Wood is extremely popular across America as the preferred material for fencing, especially when treated properly. Aside from providing privacy for homeowners, it improves the aesthetics of your home. Additionally, it offers homeowners a warm, welcoming feel at a low cost compared to other materials. When constructing the wooden fence, consider local laws regarding how high a fence should be and remember that the size and height will determine the amount of lumber, labor and consequently the price.

Wooden fences take time to complete a full fence installation but can last a lifetime. In addition, the quality of the fence depends immensely on the type of wood one chooses to build the structure.

PVC fences

The cheapest way to build a fence for your house is to buy one made of PVC. Such fences replace wooden slats and posts to provide your protection from the outside world. PVC sleeves improve the stability of wooden posts used as a fence, reducing material costs and labor. In addition, PVC poles can be attached to crossbars with adhesives and screws.

PVC fences are highly resistant to elements such as snow, rain and sunlight, ensuring they will serve your home for years.

Wrought Iron Fence

Wrought iron is a durable and strong fencing material that can withstand harsh weather conditions with minimal repairs. Wrought iron fences are a popular gothic and century-old look that creates aesthetic appeal while providing sturdy security for most homeowners. Compared to other types of fencing, refinishing and custom fabricating wrought iron makes it a bit expensive.

vinyl fences

Aside from being cost-friendly, vinyl fencing’s flexibility, strength, and color retention make it an attractive choice for most homeowners. Some experts argue that vinyl fences are approximately four times stronger and more flexible than wooden fences. Vinyl fences are easy to maintain as you can remove graffiti and other stains with soap and water. The long lifespan and low maintenance requirements make vinyl fencing cheaper than other types of fencing.

chain link fences

Chain link fencing is an inexpensive type of fencing that can serve your home for many years. The primary role of this type of fence is to create physical barriers to intruders entering and pets and children exiting in school playgrounds. The material is very durable, cheap and requires little maintenance. However, chain links are prone to rust and do not provide privacy to your home.

You can grow fast-growing vines, shrubs and flowers at the base of the chain link fence for a bit of privacy.

electric fence

Electric fences, installed by a fence installer, are commonly used to provide a low cost deterrent to human and animal intruders. The electric fence has a simple construction with a receiver, transmitters and several wires stretched between upright wooden posts. Electric fences offer the highest level of security at a lower price by sending a high-intensity pulse of voltage when a wire breaks. From now on, such fences are no longer allowed in urban centers and near highways or roads.

stone fences

Stone and brick walls have an aesthetic appeal and offer homeowners excellent privacy. In addition, these fences are strong and sturdy, providing security for your home. However, the cost of stone fences can be increased by the extensive labor required during construction.

picket

Picket fences are a popular and affordable type of fence in the United States that provide privacy and protection for your property. The vertically spaced slats attached to the bottom and top horizontal rails are available in a variety of decorative styles that will add curb appeal and home value.

palette

A fence builder can simply fasten pallets horizontally or vertically between vertical posts as a fence. As pallets can be offered freely by nurseries, construction sites and industries you should ensure that they carry an International Plant Protection Convection logo. The organization ensures that the pallet is fumigated and heat treated to limit the spread of plant diseases and critters.

Barbed Wire

Barbed wire fencing is an inexpensive and secure way to create physical barriers to keep livestock from leaving your yard and to prevent entry of wildlife such as foxes and jackals.

grid above

A trellis fence is a wooden fence that may have metal forming the cross pattern over the wooden fence to allow sunlight to enter. In addition, it offers a view of the outside while preventing intruders from entering. In addition, the trellis can support climbing shrubs such as grapevines and make your home more attractive. The smaller slats at the top of the fence reduce the amount of wood panel used compared to traditional fences, making trellis a cheaper fencing option.

natural fence

Hedgerows have been used as fences to protect homes from intruders and soil erosion since the 16th century. Planting shrubs requires researching the native plants and choosing the best plant whose mature size will provide adequate enclosure. It would be most beneficial to visit the local nursery for information on the best plants to grow as your natural fence. To keep the process cheap, harvest plants grow quickly, require little maintenance, and carry out planting during the rainy season.

Although yew trees take years to form a mature hedge that will protect your home, it offers an aesthetic appeal that is ideal for both sunny and cloudy climates. Alternatively, you can grow spotted laurel around the stone wall to provide aesthetic appeal and privacy from neighbors and intruders. The bushy green plant is hardy as it can survive salty winds and air pollution. You can choose from a variety of privet species to grow your fence, which can grow to around five to three feet tall.

You can opt for bamboo fencing that will make your home look more eco-friendly and increase its appeal. Bamboo cane and rolled bamboo use poles that connect together, creating a stronger fence than live bamboo. Homeowners living in areas with colder climates should avoid planting bamboo as a fence.

Which is cheaper, a vinyl or a wooden fence?

Find out more about All Over Fence and our products.

As is so often the case in fence construction, the answer depends on it. As a general rule, Fencing Direct recommends a minimum foundation depth of 24 inches for a 4 foot fence plus an additional 3 inches for each foot of height (e.g. 27 inches for a 5 foot post). The minimum hole diameter should be four times the largest cross section of the post.

These are the general recommendations that serve as a kind of baseline or minimum guideline. However, several factors affect the recommended (or required) depth of the foundation. Environmental factors such as soil and weather conditions can have a significant impact on a fence’s stability and require adjustments during installation. Local ordinances often regulate the minimum depth of the foundation and other elements of fence construction.

This article will walk you through the factors that determine proper foundation depth, then provide basic fence post installation instructions. Our Fencing Direct sales and service associates have decades of industry experience and can assist you in installing the highest quality products.

ground conditions

The Chain Link Fence Manufacturers Institute publishes a guide with a formula for determining foundation depth. One of the factors in this formula focuses on a soil’s stability based on its composition. There are three types of soil: sand, loam, and clay. While floors are often a combination of the three, each has its own characteristics that affect a fence’s stability.

Sand – The coarsest of all soils, and therefore the most porous, sand does not change significantly with changes in moisture conditions. Contrary to popular belief, sand can prove strong and stable once compacted. It provides a suitable medium for fence construction and requires few special considerations.

Clay – Clay, slightly less porous than sand but still fairly coarse, changes little under moisture conditions. However, due to its soft and flexible nature, it offers less stability. This should be taken into account when planning the depth of the foundation.

Clay – Unlike sand and loam, clay soil is dense and hard. It provides a stable base when dry, but is much more susceptible to expansion and contraction from water and moisture. This means that when clay soaks up water or dries out, it will shift in a way that can prove problematic for fences.

The US Department of Agriculture maintains a Web Soil Survey site that provides soil information for every location in the United States. Refer to this map and use your knowledge of soil conditions to adjust the depth of the fence foundation.

weather conditions

Wind – Another important factor in the Chain Link Fence Manufacturers Institute guide to foundation depth is wind force. It is perhaps the most important factor in determining foundation depth as it is the only force that can be reasonably predicted. The higher the wind force (common in areas with intense storms), the deeper the post.

Frost Line – Frost and dew can also exert a powerful force on a fence. One such force, called a heve, occurs when ice forms under a fence post and causes expansion that “lifts” the post. To prevent this phenomenon, the fence post must be set deeper than the frost line, or the maximum depth at which the ground freezes. The National Snow and Ice Data Center releases a map of average winter frost lines across the United States.

So consult local laws

Local governments often take these conditions into account and regulate the minimum foundation depth. Cities often post these regulations online (for example, here are Miami-Dade County’s fence regulations, which require a minimum foot depth of 38 inches). These regulations can often be found with a quick internet search, but one can also contact the appropriate government agency to speak to a knowledgeable person.

dig the hole

Regardless of the various factors affecting foundation depth, the foundation itself must be dug properly to ensure maximum strength. This means digging a bell-shaped hole, or a hole that is wider at the bottom than at the top. The opposite of a bell-shaped hole would be a carrot-shaped hole (thinner at the bottom, wider at the top). Bell shaped holes add stability by providing more support at the very bottom of the post, keeping it upright and aligned.

For Fencing Direct, we recommend that the end post feet be 10″ wide at the top and 12″ wide at the bottom. The line posts should be 8 inches wide at the top and 10 inches wide at the bottom.

Adjusting the End Post and Line Post

Once the foundation has been dug to the correct shape and specifications, the posts need to be set with concrete. For a proper mix, use 1 part cement, 2 parts sand, and 4 parts gravel. Make sure the solution is heavy and not too watery as this can cause cracks and weaknesses in the concrete. While the concrete is still wet, use a spirit level to ensure the post is perfectly vertical. Finally, at the base of the post where it meets the ground, make sure the concrete slopes away from the post to allow for proper drainage.

Fencing Direct supports you every step of the way

We work with one of the most established manufacturers in the country, delivering quality products to your door at a great price, while our staff of trained professionals can guide you through the entire process. While you are planning, our fence builder will allow you to draw your entire project and receive a price and list of all items required to complete your fence. Our customer service representatives provide quick answers to all your questions, ensuring you always have an experienced and knowledgeable contact just a phone call away.

With an investment like a fence, you want to be sure you’re getting a quality product at an affordable price. Fencing Direct offers both in addition to excellent service. Contact us today to start your project and see how much you will save.

Photo of chain link fence with decorative design by Editor B/Flickr.

Objectively speaking, chain link fences are part good, part bad, and, it has to be said, part ugly. Still, many homeowners might be cautious about describing them in that order, with the good qualities outweighing the less than desirable qualities. Regardless of your not-so-objective feelings about this ubiquitous frontier material, one thing is certain: chain link is a workhorse that will last for decades with little or no maintenance. And you can hardly say that about any other standard fence.

The good

Quality chain link fencing is strong, resilient and extremely durable. No amount of snow, rain, UV rays, high winds, or flying baseballs will stop your fence from standing up and doing its duty. In contrast, cedar fencing (the choice of the people) is far more susceptible to all of these destructive forces.

The other main advantage of chain links is that they are relatively transparent – which is also one of their main disadvantages, depending on your perspective. If you’re in the former camp, you might not like how monolithic wooden panel fences fragment the landscape and make a backyard feel a bit like an office cubicle. Chain links are especially good for dividing small yards that are adjacent to each other (especially if the homeowners are friends). The open mesh of chain links also means the fence won’t block sunlight into gardens and other areas that crave sun rays. In terms of cost, chain link is cheaper than wooden privacy fencing, lasts longer and requires no refinishing, so the lower cost gets even better over time.

The bad

In terms of practicality, Chainlink has two main drawbacks: it’s relatively easy to mount and, as mentioned above, it’s see-through. The climbing problem can be a problem for people with unusually talented or overzealous dogs. Wooden fence manufacturers may argue that chain links are less secure than their own products, but the reality is that any sane scoundrel or kid running from the fluff can easily scale a 6-foot wooden fence from either side. The issue of privacy is another matter. Chain links don’t create a privacy (or wind) barrier unless you fill the fence mesh with these aluminum or plastic slats. Decide for yourself if that’s aesthetically pleasing.

the ugly

Few can argue that chain link fences offer a lot of decoration. At best, it’s not very noticeable. At worst, it can have all the charm of a prison yard. The standard chain link is available in one colour: zinc. And painting is a lot like painting concrete and brick: It turns an inherently low-maintenance material into a three- to five-year pain in the butt. However, if galvanized metal really isn’t your color, you can opt for PVC or polyester coated fences, which come in standard colors like green, brown and black. Just be aware that this bling can double or triple the cost of the fence.

The options

Standard chain links may all look the same to the layperson, but there are important quality differences. When purchasing a fence, consider its four main components:

Grating (or “fabric”) Framework (posts and rails) Hardware (connectors and brackets that hold everything together) Coating (for rust protection and paint if needed)

Heavier gauge mesh and scaffolding is stronger and more expensive than lighter gauge, smaller diameter materials. Fittings should be well finished and uniformly shaped. Coatings include standard galvanizing—a layer of zinc added before or after parts are formed—and PVC or polyester. The plastic coatings are applied to the galvanized metal and provide additional rust protection in addition to the paint. As a general rule for primary fencing materials, follow ASTM standards for your application, as well as any specific recommendations dictated by your city building authority or local climate.

The installation

DIY installation is a reasonable option for savvy homeowners. Chain link is fairly easy and requires basic tools, except for a fence stretcher which is essentially a fancy come along (hand winch). As with all fencing, careful planning and accurate layout and post placement are key. With chain links, stretching, fastening, and cutting or splicing the mesh to get it just right can be difficult, and gates require special attention to detail. In the end, most people choose to hire a fencing professional. Regardless of who is doing the work, remember the following: Check with your local building authority before seriously planning to add a new fence or remove an old one; Believe it or not, residents of Alexandria, VA are in trouble with local authorities for removing their dilapidated 1950’s chain link fence, which the city considers to be of historical value.

Updated April 10, 2018.

If you’re thinking about securing your property with a fence so you can let your kids play safely or let your pet outside with ease, there are a few important considerations to keep in mind. Several options are used to construct fences and this guide will examine wood and chain links. In the following sections, we explain the differences between these options so that you can make an informed decision.

Style Wood fences offer the greatest versatility in terms of design and finishing options. These fences can be painted to match your home’s exterior and decorative features, and trellis work or metal fixings can be added for a customized look. Wooden fences can be constructed from various types of wood, the most common being pressure treated pine. Spruce and cedar are other possible options. These fences vary in height and include ranch/split rail, picket, and privacy screen styles. Chain link fences have fewer design options and are usually limited to black, green, brown, or silver colors. Generally chain link fences are used where privacy is less important and their purposeful design is ideal for enclosing pet areas, around HVAC units or in industrial settings. The fence material is galvanized aluminum and can be coated with Vinyl 1. Chain link fences are typically only 4 feet high but can be built up to 5 or 6 feet high.

installation

Both wood and chain link fences can be installed as a DIY project. However, a significant amount of work is required. Digging holes for fence posts 2 takes a great deal of time and effort and typically requires specialized equipment. Fence Post 2 should be cemented into the ground to prevent shifting or tilting over time. Due to the required permits, site inspection and rating 3, the use of a professional is recommended.

With wooden fences, each fence board must be individually nailed to 4 posts. Depending on the size of the fence, this can take several hours. Chain link fencing is sold in large rolls so after the posts are installed, the fencing material is unrolled and attached to each post. This makes for a faster installation.

Cost The cost of a wooden fence depends on the style, height and type of wood selected. For a 6 foot high, 209 yard privacy fence 5 with a gate, concrete posts and the removal of the old fence, the material cost ranges from $8 to $18 per linear foot. Labor costs range from $25 to $50 per worker based on hourly billing. The total cost of this project ranges from $6,500 to $10,000. However, many companies offer a package deal so homeowners are not surprised by additional costs. Chain link fences are a cheaper option that can make them attractive for covering large areas that need security, such as around a commercial or industrial area. For a 4 foot tall fence that is 209 meters long, material prices range from $7 to $12 per linear foot. Labor costs range from $8 to $15 per linear foot, so the total cost for this project averages from $3,000 to $5,200. Additional items such as gates, vinyl 1 slats or fabric screens increase the overall cost.

privacy

Wooden fences can provide considerable privacy depending on the design used and are ideal for securing a space used for play, relaxation or entertaining. A wooden fence can be built at different heights to provide additional privacy, e.g. B. around a pool area.

Chain link fences don’t offer much privacy because the mesh has large gaps that allow these fences to practically see through. Slats can be built into the material of the chain links, which provide some privacy. Chain link slats are usually sold by the box. They come in a variety of colors to help your fence blend in with the rest of your property. A box of slats costs about $45, and professional installation adds $2 to $3 per linear foot to installation costs. Since the material of the slats is visually unsightly and not very durable, this option is not widely used.

Light wood fences can completely block the light and may not be the best choice if you have plants or a garden nearby. Chain link fencing lets in a lot of light and can be ideal when you simply want to restrict access to your garden or want to protect a specific area like a vegetable garden.

maintenance

Wooden fences require considerable maintenance to keep them in good condition and looking good. Depending on the paint used and the climate you live in, your wooden fence may need to be sanded 6 and painted or stained annually. Damp or wet climates can cause the wood to rot, and termites can also be a problem. If the posts are not properly installed and cemented into the ground, they can tilt or fall, likely damaging the portions of the fence near the damaged post. Depending on the extent of the damage, repairs can be costly as parts of the fence may need to be rebuilt using new materials.

Chain link fencing requires little maintenance because the metal and other materials used are very durable in a variety of climates. The galvanized metal has been treated with a special process that makes it less prone to rusting. Metal is also stronger than wood and will not sag over time like a wooden fence.

Lifespan Typically, a wooden fence lasts about 15 years before it needs to be replaced. A chain link fence will last around 20 years and if you have chosen a vinyl covered mesh you can expect an even longer lifespan.

sustainability

Wooden fences may initially seem like a sustainable option, but this depends on where and how the wood was harvested. Cutting down old-growth forests for lumber can cause significant damage to the surrounding ecosystem. Also, many wood products are treated with toxic chemicals to prevent the growth of insects and mold. Chain link fences are made from easily accessible raw materials, but still require a significant amount of energy in the manufacturing process.

You may need to obtain a permit to install a fence, but don’t let that put you off. A good fence can be one of the wisest investments you make in your landscaping. Fences can serve a number of functions, both practical and decorative.

When you will most likely need a permit to build a fence

Where you live, where you will erect the fence on your property, and how tall you want your fence to be are three factors that have a large impact on how likely or unlikely you are to get a fence installation permit :

If you live in a densely populated county, chances are you’ll need a permit.

On the other hand, if you’re a farmer wanting to erect a barbed wire fence in a rural area, chances are you won’t need a permit.

Where you install the fence within your own property also makes a difference. A privacy fence in your backyard often doesn’t require a permit unless it’s supposed to be over 6 feet tall, depending on where you live, while the limit for the same type of fence in your front yard might be as low as 3.5 feet.

Regardless of how likely you are to need a permit, you should always inquire as to whether or not you actually need a permit. Better safe than sorry. If you don’t want to run into problems once the work is underway, it’s crucial that you are comfortable with the forces that are at hand. You can then focus on getting the actual building properly finished without fear of a building inspector showing up and throwing cold water on your project.

Obtaining permits, other preparatory work and beginning installation

As with so many other DIY projects, part of the key to success is getting the prep work done right. Here are some points to check before installing the fence:

To find out if you need planning permission before installing the fence, check with your city’s building control department or check with your local city hall. Often this and more information can be found on your city’s website.

A fee may be charged at the time your application is submitted or your plan is approved.

Additionally, some cities may ask you to sketch a plan of your proposed fence, accompanied by photographs and written approval from your neighbors.

Approval is one thing, getting a neighbor to pay for a privacy fence that runs along the property line you share is quite another. While some may feel that neighbors should shoulder the burden since they too will benefit from the extra privacy, it’s not a good idea to demand such a payment out of the blue. This could create ill will. Of course, it is completely different if you have spoken to the neighbor right away and have already agreed that a joint investment in a fence to achieve privacy makes sense for both of you.

Have a surveyor determine exactly where your property line is unless you are already certain of the location in question. Some municipalities only require that you have located the corner markers. Alternatively, just make sure the fence is well within the boundaries of your own property and not near your property line.

You need to determine the location of underground gas, water and power lines before digging.

Warning Whenever you plan to dig holes on your property, be sure to call the national call-before-you-dig number (811), even if you are already certain of where your utility lines are located. In most locations, it is illegal to dig more than a few inches deep without having your utility lines located and marked by a licensed utility locator.

When determining whether or not you need a fence permit, you will likely receive additional information that will be of great value to you.

Even if your application is accepted, you’re still not out of the woods. Some municipalities will give you a list of inspections that must take place during installation. Successfully passing these inspections will prepare you for a final inspection that will give your structure the government’s seal of approval.

For example, building codes and local building code ordinances may dictate that a fence 6 feet or more high must be at least 15 feet from the street. Such restrictions may bother you, but they often make sense. For example, a privacy fence on a corner lot should not be so high as to obscure the view of drivers at the intersection of the two streets that your lot borders, which could pose a safety hazard.

Now that you’ve decided to use chain links for your brand new residential or commercial fence, you need to choose the exact chain link fence you want to install – I know you thought the hard part was over! There are different types of materials, grades and types of chain link fencing that you can choose from. Here are some tips for choosing the best chain link fence for you.

wire material 101

There are three types of wire materials that you can typically choose for your chain link fence: galvanized or galvanized, aluminum, and stainless steel.

Galvanized: Galvanized wires are dipped in zinc and then electroplated. Some are galvanized after weaving and others are galvanized beforehand. Most people prefer the former finish, but both types typically last around 12 years with minimal maintenance.

Aluminum: Aluminum wire is inherently resistant to rust or corrosion, adverse weather conditions and wear. Aluminum wire chain link fencing is typically chosen for commercial or public use. These can last up to 25 years with minimal maintenance.

Stainless Steel – Stainless steel wires are the strongest and most durable (but also the most expensive). They don’t fall prey to the problems that other guys can have. Stainless steel chain link fencing is typically found on high-end fencing or barriers at airports, railroads, or the sides of highways.

Additional protection 101

Aside from the durability of the wire material itself, many homeowners and business owners choose to add some protection by adding paint or plastic coating to their chain link fence.

Paint: Paint can add a little more aesthetic appeal to your chain link fence, but can be prone to cracking and chipping over time. The pain usually lasts 3-5 years on a chain link fence before needing reapplication.

Plastic Coating: Plastic coating uses PVC to provide long-lasting protection for your chain link fence without being prone to cracking or peeling. PVC also protects your chain link fence from rusting, scratching or other imperfections.

Wire size and mesh size 101

Finally, you need to select the correct gauge wire and mesh size for your chain link fence. These depend mostly on how much security you need for your property and how much tension you think your fence will be able to withstand. If you need higher security, opt for small mesh sizes and wire gauges. If you want your chain link fence to withstand a lot of tension, also opt for a smaller mesh size and smaller wire gauges.

Let us help you choose the right chain link fence for your home

Ready to have your perfect chain link fence installed around your residential or commercial property? Hercules Fence has extensive experience repairing and constructing fences in any material. Our experienced team can help you meet your fencing needs, whether it’s residential or commercial fencing, at the right price. Call us at 757-316-3600 or visit us online. To see examples of our work and keep in touch, don’t forget to follow us on Facebook, Twitter, Google+, LinkedIn, Flickr and Pinterest.

Is your fence not high enough for your needs? Do you find it difficult to keep your pet inside your fence?

Did you know the average chain link fence is 4 feet tall? That might work for some. But for others, a 4 foot fence may not be high enough. Everyone has different fencing needs.

For example, one person’s fence might keep children outside, while another person’s fence might keep a large dog inside. Whatever the reasoning, a fence should be strong and exactly what the owner wants.

If a 4 foot fence doesn’t fit your fencing needs, this item is for you! There are many ways to raise your chain link fence, so you’ll be able to find a way that works for you!

1. Add welded wire to the top of your fence

One way to raise your chain link fence is to add material to the top of your fence. This is one of the easier ways to make your fence taller since you don’t have to change anything from the previous fence material.

A material that works well in this situation is welded wire.

Welded wire is wire in a checkerboard pattern that is heat welded, making the fencing material incredibly strong.

This type of wire is similar to a chain link fence, so using it can be a good option if you’re looking for an easy way to lengthen your fence while maintaining a similar look.

To do this, you should buy welded wire from your local hardware store. About 36 to 50 inches of cabling will do.

You can use galvanized wire to attach the welded wire to your chain link fence. Pliers work well to tie the wiring together.

Once you’ve attached the welded wire to the top of the chain link fence, you should bend the top 12 inches of the welded wire in at a 90 degree angle to prevent animals from climbing out.

Sometimes T-posts must be used to support the welded wire along the fence. This creates a higher fence to protect your yard from larger things.

2. Add mesh cloth to the top of your fence

Similar to adding welded wire to the top of your chain link fence, adding mesh fabric to the top of your fence is another way to raise the fence.

Mesh fabric, or hardware fabric, is a small, sturdy knitted product sold in rolls at hardware stores. It is usually made of metal or plastic. Mesh cloth is easy to cut so you can use it for many projects around the home.

Adding mesh fabric to your fence works well because mesh fabric will stand upright without additional support.

To add chain link fabric to your chain link fence, unroll the fabric and cut off the amount you need for your fence.

Balling wire is used to attach the mesh to your fence, but T-posts work for this situation as well. Pre-cut wire also works to add extra support for the mesh.

So you take the pre-cut mesh fabric and add it to the top of your chain link fence. Then attach it with whatever you think works best for your fencing material and then your chain link fence will be the height you want!

Like adding welded wire, mesh is one of the easier ways to increase the height of your fence since you don’t have to take apart your entire fence.

3. Add Tenax to your chain link fence

Another material that you can add to your chain link fence to add height is Tenax.

Tenax is a plastic fencing material that you can purchase at your local hardware store. You can buy Tenax in rolls and in many different colors. There are no sharp edges or wires on Tenax, so it’s safe for people and pets.

Tenax might be a good option for your chain link fence if you’re trying to keep your pets in your yard, but it may not be the best choice if you’re trying to keep dangerous things like wild animals or criminals out of your yard.

Similar to a welded wire material, you can attach Tenax to your chain link fence with galvanized wire or bale wire. You may need to add T-posts to add extra support for your fence extension.

4. Use PVC piping or New Line Posts to extend fence posts

Instead of adding fencing material to your existing fence, there is another option. You can disassemble your fence and add material to your fence post to create a taller chain link fence.

This is a good option if you want your fence to look the same as your neighbors or just your personal preference.

The highest height you can reach without completely replacing your fence posts is 6 feet. So if you want a fence more than 6 feet tall, this may not be the option for you.

You can either use PVC pipe or buy new fence posts to extend your fence posts. It comes down to personal preference. The video below talks about adding PVC pipe, so keep that in mind.

The video above gives you an idea of ​​what fence post extension looks like, but here is a detailed guide on how to extend your fence posts to make your chain link fence higher.

1. Measure the old fence

Before you do anything, it’s important to measure the old fence. You need to know the measurements of the fence posts so you know what materials to buy.

As you do this, you should also count the number of fence posts in your chain link fence.

2. Buy the fence materials

This is an obvious step, but it’s important to make sure you have all the things you need.

Row posts and corner posts that are larger in diameter than the existing posts.

6ft chain link fences (Remember you can’t get anything higher than 6ft – you don’t want to completely rebuild the fence).

, don’t climb higher than 6 feet – you don’t want to end up completely rebuilding the fence). screws.

Make sure you plan ahead and get the right number of fence posts you need. You’ll also need some basic tools if you don’t already have them, like a rubber mallet, drill, tape measure, and pliers.

3. Remove the old fence

First you need to loosen the zip ties holding the chain link to the post. It only takes a few twists and works with pliers. Once the chain link fence is loose you can roll it up and set it aside.

Next you want to remove the horizontal connectors. Be sure to mark them so you can place them back in the same position. An easy way to do this is to mark it, but also put it on the ground where it belongs so you don’t lose it.

Then take the cap sections off the fence posts. This can usually be done with a light tap of a hammer to loosen them (or large channel locking pliers if needed to twist and loosen). Don’t forget the horizontal bars!

4. Create the new fence posts

In this step you will extend the fence posts to create your 6 foot fence posts.

First, take either the PVC pipe or the new wire post and place it over the previous fence post. You measure out how high you want to make the fence and mark the position where you want the extended piece to go.

This may require some force, which is where the rubber mallet will come in handy.

Once the previous fence post is marked, you can drill two holes at 90 degrees. You will then use screws to attach the PVC pipe or new conduit post to hold it securely to the post.

You should repeat this step for each fence post for your chain link fence.

5. Add the cap and horizontal connectors

Now that the posts are extended to the desired height, you can place the cap on the posts. Use a wrench to make sure they are tight.

Then reinstall the horizontal connectors that extend between the fence posts to create the structure of the fence. Do this until you have all of the horizontal connectors back on the fence.

6. Add the new fence

Once the frame of the fence is in place, you can attach the new chain link fence. Use zip ties about every 24 inches, starting at one end of the fence and ending at the other. Make sure the fence is taught as you go without too much play.

Continue for the rest of the fence!

There are many ways to increase the height of your chain link fence, so it depends on what works best for your fence, your timing, and your budget.

We hope this post has helped you in your decision to extend your chain link fence.

Aside from enclosing your property, fences are an excellent way to improve the appearance of your home and increase its value. With quality materials and maintenance, a properly constructed fence can serve you for many years without the need for replacement or repair by a fence installer. The cost of installing a fence depends on various factors such as: B. length, height and material type. Longer and taller fences require more labor and materials to build compared to shorter and lower fences.

Although building a fence around your home can be expensive, you can combine hard work, research and creativity to discover the most durable and aesthetically pleasing fence within your financial means. The cheapest and most affordable fences result from cheap materials that require minimal maintenance and easy fence installation. The most common and cheapest types of fencing include naturally occurring, recycled, and manufactured materials that require the least amount of labor to install and maintain.

Aluminum fences

Aluminum is among the most attractive and simple types of fencing available on the market. While it doesn’t offer the security most homeowners demand, it’s relatively cheap in terms of maintenance costs. In addition, installing an aluminum fence requires maintenance during installation, during which you decorate and paint it.

wooden fences

Wood is extremely popular across America as the preferred material for fencing, especially when treated properly. Aside from providing privacy for homeowners, it improves the aesthetics of your home. Additionally, it offers homeowners a warm, welcoming feel at a low cost compared to other materials. When constructing the wooden fence, consider local laws regarding how high a fence should be and remember that the size and height will determine the amount of lumber, labor and consequently the price.

Wooden fences take time to complete a full fence installation but can last a lifetime. In addition, the quality of the fence depends immensely on the type of wood one chooses to build the structure.

PVC fences

The cheapest way to build a fence for your house is to buy one made of PVC. Such fences replace wooden slats and posts to provide your protection from the outside world. PVC sleeves improve the stability of wooden posts used as a fence, reducing material costs and labor. In addition, PVC poles can be attached to crossbars with adhesives and screws.

PVC fences are highly resistant to elements such as snow, rain and sunlight, ensuring they will serve your home for years.

Wrought Iron Fence

Wrought iron is a durable and strong fencing material that can withstand harsh weather conditions with minimal repairs. Wrought iron fences are a popular gothic and century-old look that creates aesthetic appeal while providing sturdy security for most homeowners. Compared to other types of fencing, refinishing and custom fabricating wrought iron makes it a bit expensive.

vinyl fences

Aside from being cost-friendly, vinyl fencing’s flexibility, strength, and color retention make it an attractive choice for most homeowners. Some experts argue that vinyl fences are approximately four times stronger and more flexible than wooden fences. Vinyl fences are easy to maintain as you can remove graffiti and other stains with soap and water. The long lifespan and low maintenance requirements make vinyl fencing cheaper than other types of fencing.

chain link fences

Chain link fencing is an inexpensive type of fencing that can serve your home for many years. The primary role of this type of fence is to create physical barriers to intruders entering and pets and children exiting in school playgrounds. The material is very durable, cheap and requires little maintenance. However, chain links are prone to rust and do not provide privacy to your home.

You can grow fast-growing vines, shrubs and flowers at the base of the chain link fence for a bit of privacy.

electric fence

Electric fences, installed by a fence installer, are commonly used to provide a low cost deterrent to human and animal intruders. The electric fence has a simple construction with a receiver, transmitters and several wires stretched between upright wooden posts. Electric fences offer the highest level of security at a lower price by sending a high-intensity pulse of voltage when a wire breaks. From now on, such fences are no longer allowed in urban centers and near highways or roads.

stone fences

Stone and brick walls have an aesthetic appeal and offer homeowners excellent privacy. In addition, these fences are strong and sturdy, providing security for your home. However, the cost of stone fences can be increased by the extensive labor required during construction.

picket

Picket fences are a popular and affordable type of fence in the United States that provide privacy and protection for your property. The vertically spaced slats attached to the bottom and top horizontal rails are available in a variety of decorative styles that will add curb appeal and home value.

palette

A fence builder can simply fasten pallets horizontally or vertically between vertical posts as a fence. As pallets can be offered freely by nurseries, construction sites and industries you should ensure that they carry an International Plant Protection Convection logo. The organization ensures that the pallet is fumigated and heat treated to limit the spread of plant diseases and critters.

Barbed Wire

Barbed wire fencing is an inexpensive and secure way to create physical barriers to keep livestock from leaving your yard and to prevent entry of wildlife such as foxes and jackals.

grid above

A trellis fence is a wooden fence that may have metal forming the cross pattern over the wooden fence to allow sunlight to enter. In addition, it offers a view of the outside while preventing intruders from entering. In addition, the trellis can support climbing shrubs such as grapevines and make your home more attractive. The smaller slats at the top of the fence reduce the amount of wood panel used compared to traditional fences, making trellis a cheaper fencing option.

natural fence

Hedgerows have been used as fences to protect homes from intruders and soil erosion since the 16th century. Planting shrubs requires researching the native plants and choosing the best plant whose mature size will provide adequate enclosure. It would be most beneficial to visit the local nursery for information on the best plants to grow as your natural fence. To keep the process cheap, harvest plants grow quickly, require little maintenance, and carry out planting during the rainy season.

Although yew trees take years to form a mature hedge that will protect your home, it offers an aesthetic appeal that is ideal for both sunny and cloudy climates. Alternatively, you can grow spotted laurel around the stone wall to provide aesthetic appeal and privacy from neighbors and intruders. The bushy green plant is hardy as it can survive salty winds and air pollution. You can choose from a variety of privet species to grow your fence, which can grow to around five to three feet tall.

You can opt for bamboo fencing that will make your home look more eco-friendly and increase its appeal. Bamboo cane and rolled bamboo use poles that connect together, creating a stronger fence than live bamboo. Homeowners living in areas with colder climates should avoid planting bamboo as a fence.

Which is cheaper, a vinyl or a wooden fence?

Find out more about All Over Fence and our products.

Type of woven metal fence

Chain link fences showing the diamond pattern

A chain link fence (also known as wire mesh, chain link fence, chain link fence, cyclone fence, hurricane fence, or diamond mesh fence) is a type of woven fence, usually made from galvanized or LLDPE coated steel cable. The wires run vertically and are bent in a zig-zag pattern so that each “zig” with the wire immediately hooks on one side and each “zag” with the wire immediately hooks on the other side. This creates the characteristic diamond pattern of this type of fence.

Evolution of the chain link fence[edit]

A chain link privacy fence topped with barbed wire protecting a utility substation.

In the UK, Barnard, Bishop & Barnards was established in Norwich to machine chain link fencing. The process was developed by Charles Barnard in 1844 based on cloth weaving machines (Norwich had a long history of cloth making up to that point).[1]

The Anchor Post Fence Co. acquired the rights to the wire weaving machine and was the first company to make chain link fencing in the United States. Anchor Fence also holds the first US patent for chain links. The machine was bought in 1891 by a man from Belgium who originally invented the wire bender.

Sizes and uses[edit]

A chain link fence lets light through while protecting the windows.

In the United States, fences typically come in 20-foot (6.1 m) or 50-foot (15 m) coils that can be joined by “unscrewing” one of the end wires and then “screwing it back in” so that it Hook both parts. Common heights include one-foot increments from 3 ft (0.91 m) to 8 ft (2.4 m) and other heights including 3 ft 6 in (1.07 m), 10 ft (3.0 m) and 12 feet (3.7 m). almost any height is possible. Mesh size is usually 9, 11 or 11+1⁄2 wire gauge. Stitch length can also vary as needed, with the standard diamond size being 2 inches (5.1 cm).

For tennis courts and ballparks, the most popular height is 10 or 12 feet (3.0 or 3.7 m). Tennis courts often use a diamond size of 1.75 inches (4.4 cm) [2], measured flat side to flat side, so power hitters can’t poke the ball in the fence.

Chain link fencing’s popularity stems from its relatively low cost and because the open weave does not block sunlight from either side of the fence. A chain link fence can be made semi-transparent by inserting fence inserts into the mesh. It is also popular to let ivy grow up the fence and intertwine.

Installation [edit]

When installing a chain link fence, posts are set into the ground and the fence is attached to them. The posts can be made of tubular steel, wood or concrete and can be driven into the ground or cast in concrete. End, corner, or gate posts, commonly referred to as “end posts,” must be set in concrete foundations or otherwise anchored to prevent leaning under the tension of a taut fence. Posts placed between the end posts are called “line posts” and are placed no more than 10 feet apart. The installer secures the fence at one end, stretches it, and secures it at the other end, slightly removing the excess by “unscrewing” a wire. In many cases, the installer stretches a lower guy wire, sometimes referred to as “coil wire,” between the end posts to help minimize the in-and-out movement that occurs at the lower end of the chain link mesh between the posts. Top horizontal rails are used on most chain link fencing, although this is not required if the end posts are properly braced. In this situation, a top tension wire can be used. Bottom rails can be added in place of bottom guy wires, and intermediate horizontal rails are often added for taller fences, 10 feet or more. Finally, the installer ties the fence to the line’s posts and rails using steel or aluminum wire with a hook on one end called a “fence tie.” The lower guy wire should be attached to the line posts and the mesh netting should be attached to the center of guy wire 2′.

Manufacturing [ edit ]

The process of making chain link fences is called weaving. A metal wire, often galvanized to reduce corrosion, is drawn along a rotating long and flat blade, creating a somewhat flattened spiral. The spiral continues to rotate past the blade, winding through the previous spiral that is already part of the fence. When the spiral reaches the other end of the fence, the spiral is cut near the blade. Next the spiral is flattened and the entire fence is moved up ready for the next cycle. The end of every second spiral overlaps the end of every first spiral. The machine clamps both ends and gives them a few twists. This will make the links permanent.

An improved version of the weaving machine wraps two wires around the blade at once to create a double helix. One of the spirals is woven through the last spiral that is already part of the fence. This improvement allows the process to proceed twice as fast.[3]

Notable uses[edit]

Chain link fence on an American short track

Chain link steel cage as used in an Impact Wrestling professional wrestling match

See also[edit]

Would you like to fence your property? One of the hardest things about installing a fence is knowing what type to get.

Fences come in a variety of materials such as wood, ornamental iron, PVC vinyl, or chain link, which can make the decision difficult. One type of fence you might want to consider is a vinyl coated chain link fence.

Discover five things you should know about vinyl coated chain link fencing.

1. Know what a vinyl coated chain link fence is

You may be more familiar with a chain link fence, which is a braided fence made from galvanized steel wire, usually coated with zinc. A vinyl-coated chain link fence is also metal; However, it is coated with vinyl instead of zinc.

The vinyl coating is made of synthetic resin or plastic. Vinyl coating helps protect the metal from scratches, rust, corrosion and other types of damage, increases the durability of the fence and improves its appearance.

2. Know the benefits of vinyl coated chain link fencing

Because vinyl coated chain link fencing comes in a variety of colors, you’re sure to find the right color to complement your property. The most popular colors for this type of fence are white and tan. Custom colors are also available, and some homeowners mix and match different colors.

A vinyl coated chain link fence has a softer appearance than a regular chain link fence, making it look less industrial.

Other advantages of vinyl coated chain link fencing are that they:

Are inexpensive

Are easy to install

Will not rot or fade

Lasts between 15 and 20 years

A vinyl-coated chain link fence is also easy to maintain.

3. Know how to maintain your vinyl coated chain link fence

Even though the chain link fence is vinyl coated, it can still get rust. The fence can rust if the coating is damaged or worn. Older vinyl-coated chain link fences are particularly prone to rusting. As soon as rust spots form, you can rub them off with a piece of steel wool.

In addition to regularly checking for rust, you should also wash your fence to keep it free of dirt and debris. You don’t need to use dish soap or bleach to clean your fence. Instead, opt for more natural cleaning products like borax, vinegar, or just plain water.

4. Do you know the cost of a vinyl coated chain link fence

The average minimum cost for a vinyl coated chain link fence is $12.85 per foot. The maximum cost is $18.45 per foot. Most homeowners will pay between $1,215 and $1,480 for a 100-foot vinyl-coated chain link fence. These prices include material and labor costs.

Some of the main factors affecting the cost of a vinyl covered chain link fence are the manufacturer, installation methods and location. The quality of the material can also affect the price. A fence made of higher quality materials can cost up to 400 euros more.

Fences in densely populated urban areas tend to cost more. Complex fence configurations, as well as larger fences, usually cost more as well. To lower the price of your fence, you may want to install it at a slower time of year.

5. Know who to contact regarding the installation of a vinyl covered chain link fence

Have you decided to have a vinyl coated chain link fence on your property? In this case, contact the Gulf Coast Fence Co. of Pascagoula, MS. We have installed fencing for residents along the entire Mississippi Gulf Coast since 1986. We look forward to speaking to you about your fencing needs, as well as answering all of your questions and addressing your concerns. Please let us know how we can help you today.