Are you looking for an answer to the topic “bathstore watermark toilet seat“? We answer all your questions at the website https://chewathai27.com/ppa in category: 940+ tips for you. You will find the answer right below.
Table of Contents
How do I know my toilet seat model?
- On the back or side of the inside of the toilet tank.
- On the back of the toilet tank.
- On the underside of the toilet bowl.
How do you remove a bathstore toilet seat?
Some modern toilet seats come with a button in between the hinges that connect the seat to the toilet. If your toilet seat has this button, simply press it and lift the seat off. If you have a standard toilet seat, you’ll need to unscrew the bolts with a screwdriver while holding the nut underneath with pliers.
Do replacement toilet seats fit all toilets?
No, not all toilet seats fit the same because toilets come in a variety of different shapes, so you’ll need to check yours before buying. There are three types of toilet shapes commonly found in UK homes. These are round, D-shape, and square seats.
How do you tighten a toilet seat without access?
In these situations, you can hold the nut in place with a pair of pliers while using the screwdriver to tighten the bolts. The wing located on the nut will prevent the bolt from turning back on itself by locking it in place. Again, keep tightening the bolt until the seat feels secure.
DIY Basics: How to Replace a Toilet Seat
If you need guidance, read on for our guide.
Can you learn how to tighten the toilet seat without access to the underside?
You absolutely can! You may feel better knowing that tightening the toilet seat without an access bottom is not difficult, although the screws may not be in an intuitive place. Often many toilet seats have small holes for access from the bottom that have just been hidden from your view.
There are other types of toilet seats that may have slightly different holes and fittings, but with a little guidance you can certainly figure those out too!
Before we get to our step by step guide on how to put on the no access bottom toilet set, let’s consider what types of tools are required for this project.
Read on for valuable information!
Is there a tool to tighten toilet seats?
Luckily, you don’t need any special tools to tighten toilet seats. In fact, you may already have them around the house or in the garage.
To create your own toilet seat fastener kit, get an adjustable wrench or socket, a flat head screwdriver and pliers as that should be all you need to tighten these toilet seat hardware.
And while it’s not necessary, you can consider wearing protective gear like gloves and goggles so your hands and eyes don’t encounter any fragments of anything coming off your toilet in the process.
How do you attach a toilet seat with concealed hardware?
Step 1: Check the toilet again
Since most regular toilets have holes somewhere for access from below, the first thing you should do again is to look for them around your toilet. A common place to look is on the seat hinges, where there may be hidden buttons you can press to dislodge the lid and reveal the mounting studs and screws.
In some cases, there are toilet seats with special covers that you may have to slide aside or simply pry up to access the fittings below. These covers protect the mounting bolts from anything that could damage the locks. In this situation, carefully look for a round-cut piece to locate the covers.
The instructions above work well for most floor-installed toilets, but if yours is in-wall installed, you may need to remove the toilet from its mounting base. The holes for tightening your wobbly toilet seat should be on the screws that attach the toilet to the wall.
Step 2: Readjust the seat
Now that you’ve found the bottom access to the toilet seat screws, you can adjust the seat before tightening everything back up. If you find that your seat is out of alignment, you probably want to true it. You can use clamps to hold it in place.
Step 3: Tighten the screws
Once you have the toilet seat centered, you can start tightening the screws. A flathead screwdriver would be best here, but if you find that a different screwdriver head works better, go for it as you don’t want to damage the screws and shorten their lifespan. Tighten the screw until it can no longer be screwed in.
In the lower entrance of some toilets, e.g. B. Soft close toilets, a special wing nut can be adjusted to get a more secure fit for your toilet seat. In these situations, you can use pliers to hold the nut while you use the screwdriver to tighten the screws. The wing on the nut prevents the bolt from turning back on itself by locking it in place. Re-tighten the screw until the fit feels secure.
Step 4: Check the tension
By now your toilet seat should be secure again. But before you pack your tools, check the tension by banging on the screws to see if anything moves. If this is the case, retighten the screws as much as possible. When everything seems secure, close the lid, making sure nothing is preventing it from closing properly. Then you are done!
How do I stop my toilet seat from moving sideways?
As an additional accessory you only need two adhesive disks. First, locate the screws that attach the toilet seat to the bowl. Then use your flathead screwdriver to hold the screw in place while you remove the nut underneath.
If it’s just a plastic nut, you can probably remove it by hand, but if it’s particularly tight or metal, use your pliers to twist it. Now remove the lid, clean the ceramic thoroughly and put the seat back in place. Put the screws back in the holes and then take your washers.
Peel off the pad and then slide each screw down until it reaches the bowl. Finally, simply tighten the nut as tight as you can, which will secure the bolt and prevent the seat from slipping.
How do you fix a toilet seat that keeps falling off?
The most common reason a toilet seat keeps falling off is that the seat was placed too far back on the tank. All you have to do is unscrew the seat, pull it forward as far as you can, then tighten securely.
Where is the brand name on a toilet?
The brand: Look under the water tank lid (on the bottom); on the inside walls of the tank; on the bowl between the bolts attaching the seat. Disregard names on the seat as they are seldom the same brand as the toilet. The number: Look under the water tank lid (on the bottom), or on the inside walls of the tank.
DIY Basics: How to Replace a Toilet Seat
Three things are needed to identify your toilet: 1.The brand 2.The number 3.The color.
The brand: look under the lid of the water tank (on the bottom); on the inner walls of the tank; on the bowl between the bolts that hold the seat in place. Ignore names on the seat as they are rarely of the same brand as the toilet.
The number: Look under the water tank cap (below) or on the inside walls of the tank.* The number on the cap may or may not be the same as that in the tank or the complete toilet model number.
* Some pre-1940 lavatories with wall mounted tanks may have the number stamped on the outside rear and therefore not visible when installed.
The Color: Online color swatches are very risky for determining a correct color name. Please study the color information page to learn more about color names. Or go directly to the Color ID Service page.
If your toilet has numbers but no name, email us. We often know which numbers belong to which brand and can direct you to the correct product page.
If your toilet doesn’t have numbers, we’ll need a photo of it.
If your gas cap is missing, see if there is another restroom in your house or neighborhood that has the same restroom that you can look at.
Q: What brand is UPC
A: UPC stands for Uniform Plumbing Code, a governing body that sets standards for plumbing fixtures. It’s not a brand. The UPC stamp simply means that your product meets the code.
Q: What is the “Celite” (Cell-e-tay) brand?
A: Celite is a South American manufacturing facility that over the years has supplied components to various American import brands such as St. Thomas Creations, Barclay Products Limited, Laufen (Burgess) and most recently Cheviot. Toilet bowls with the Celite logo on them were actually sold under a different brand name.
Cross reference between part number and brand name
* Here is a cross reference of the Briggs tank numbers and the corresponding gas cap/cap number:
F2000, F2002, 2004, F2005, 2006, 2007, 2006-7, 2009, 2009, 2012, 2092, 4010, F4033, 4036, F4040, F4043, F4049, F4056, F4056, F4052 4078 Briggs *1 830, 1000, 1100, 3000, 4000: Case222, 3-222, CR/PL, 3-615, 9-742, 3-540, 3-543, 4-15-001, 4-26-001: Crane1190, 5149, 5240, 5540, 191.697, 101097, 141 0120, 1510100: Eljer201 52, 201, 201-R, 201WS: KilgoreMPP-10, MPP51, MPP-160, MPP201-216, MPS KPP 7S: MansfieldN, NI Norris F2149, F4050, F4053, F4054, F4055, F4056, F4057, F4060, F4063, F4072, F4080: Standard RU44, RU45, RU51, RU67, 3017, RU86, 3427, 34434, RU 34434, RU 3434, RU 3434, RU 3525, 3525, RU 3451 , Ru3457, 3459, Ru3636, Ru3858, 4002, 4003, 4005, 4006, 4012, 4013, 4022, 4023, 4470, 4031, 4431, 4431, 4437, 4439, rud 4471, 4437, 4439, rud 4471, 49481, 4474, 4474 universal (UR)Tank 2241 – Lid 3341Tank 7240, 7340 – Lid 7401Tank 4422 – Lid 7412Tank 4420, 4421, 4450 – Lid 7419tank 4425, 4428, 4930, 4950 – Lid 7421 or 4930tank 4480, 4980 – Lid 7430tank 4486, 4985, 4986 – lid 7435 tank 4408 – 4408 – 2408, 4408 4432, 4433, 4440, 4442, 4443 – Cap 7469Tank 6022, 6024, 6026 – Cap 7422Tank 6080, 6085 – Cap 7427Tank 6080, 6085 – Cap 7427Tank 7250 – Caps have no numbers or numbers1 – Caps and we cannot supply parts for these units deliver.
What are the different shapes of toilet seats?
- Round Toilet Seats. Round toilet seats are the most common type of toilet seat and are, as you may have guessed, round in shape. …
- Elongated Toilet Seats. …
- Comfort Seats. …
- Raised Toilet Seats. …
- Bidet Seats. …
- Open Front Seats.
DIY Basics: How to Replace a Toilet Seat
In this article, we’ll go over the different types of toilet seats so you can make an informed decision about which one is right for you.
Don’t be surprised if you learn something new!
What to consider when choosing a toilet seat
When you need a new toilet seat, you don’t want to just go to the hardware store and just pull any old toilet set off the shelf.
There are a few things to consider when shopping to ensure you’re getting the right type of toilet seat for your needs, personality, and aesthetics.
measurements
First you need to measure your toilet to make sure you get the right size. You don’t want a toilet set that’s too big or too small for your bowl. The last thing you want is an ill-fitting seat that keeps falling down or is so tight you can’t even put it on.
To get an accurate measurement, use a tape measure to find the length, width, and height of your toilet bowl. Be sure to write down the measurements or take a picture of them so you don’t forget them when you go to the store!
material and colour
You also need to decide what material you want your toilet seat to be made of. The most common materials are wood, plastic and bamboo, although they also come in other materials as we will discuss later in this article.
You should also consider the material of the bolts and hinges. Stainless steel and galvanized are the most durable, while plastic is easier to clean and won’t rust.
The color you choose is entirely up to you, and there’s a ton to choose from! You might want it to be a neutral white, black, or bisque. Or you might want to match your bathroom’s color scheme or pick a fun and funky color to make a statement.
durability and comfort
Durability and comfort are two other important factors to consider when choosing a toilet seat. You might want something that you can sit comfortably on for long periods of time if necessary. And of course, if you have kids or a lot of traffic, keep durability in mind.
For example, a wooden toilet can be a good option if you want comfort that stays warm. However, it is difficult to keep clean and may need to be sanded and refinished every few years to keep it looking its best. Plastic toilet seats, on the other hand, are colder and less comfortable, but they’re much easier to clean.
Special considerations
Sometimes there are special considerations, e.g. For example, if you or someone in your family has a disability that interferes with using the restroom, or you have young children of your own, or run a work-from-home business that involves many children, such as a daycare.
For example, if you or someone has a disability that affects using the bathroom, consider a raised toilet seat or bidet seat. A bidet seat attaches to your toilet and provides a jet of water for cleaning after using the toilet, and raised toilet seats are ideal for those who have trouble bending over or sitting low. They add a few inches more height to the seat, making it easier and more comfortable to use.
Seats with built-in night lights are also available, which can be helpful if you need to go to the bathroom in the middle of the night and don’t want to turn on the bright bathroom light.
Some seats also come with a soft close toilet seat, which is great if you have small children or pets who enjoy playing with the toilet seat. It keeps the lid from slamming shut and hurting little fingers (or dicks!).
Now that we’ve discussed a few things to consider, let’s take a look at the different types of toilet seats that are available in the market
What Are the Different Types of Toilet Seats?
As I mentioned earlier, there are a variety of toilet seats on the market. Toilet seats come in all shapes, sizes, colors and materials.
Types of toilet seats that we include in this article are round, oblong, comfortable, raised, bidet and open front.
Here is a list of the different types of toilet seats in detail:
1. Round toilet seats
Round toilet seats are the most common type of toilet seat and, as you might have guessed, are round in shape. They are usually made of plastic or wood and come in a variety of colors. Round toilet seats are usually the cheapest option.
One downside to round toilet seats is that they can be uncomfortable for people with certain disabilities. Another disadvantage is that they may not go well with certain types of toilets, e.g. B. to oblong toilets.
2. Elongated toilet seats
Oblong toilet seats are oval in shape and are designed to fit oblong toilets. They tend to be more comfortable than round toilet seats as they offer more surface area. Oblong toilet seats are usually made of the same materials as round toilet seats.
The difficulty with oblong toilet seats is that they can be difficult to find since they are not that common. They are also more expensive than round toilet seats.
3. Comfort seats
Comfort seats are designed to be comfortable! They are often padded and may even have a built-in heating element. Comfort seats are usually made of soft materials such as foam or fabric.
One disadvantage of comfort seats is that they are not as durable as other types of toilet seats. They may also not be as easy to clean as they have more nooks and crannies for dirt and bacteria to hide.
4. Raised toilet seats
Raised toilet seats are designed for people with mobility issues. They increase the height of the toilet seat, making it easier to sit down and stand up.
Raised toilet seats are usually made of plastic or metal. They are also usually padded for comfort.
The disadvantage of raised toilet seats is that they are difficult to install. They also may not fit all types of toilets.
5. Bidet seats
Bidet seats are a type of toilet seat that comes with a built-in bidet. Bidets are devices that spray water to clean your butt after you’ve used the toilet.
Bidet seats are usually more expensive than other types of toilet seats. They’re also not that common, so they can be hard to find.
6. Open front seats
Open front toilet seats are the U-shaped seats you’ll find in virtually all public bathrooms. You will find these in public places because they are mandated by the IAPMO (International Association of Plumbing and Mechanical Officials). According to the 2018 Uniform Plumbing Code 411.3, all public toilets should have open front toilet seats or an automatic seat cover dispenser.
The reason for these U-shaped seats is hygiene. When children use the toilet, someone does not raise the seat, or someone squats instead of sitting in a public restroom, urine often drips onto the front of the seat and down the front of the bowl. Eliminating that part of the seat keeps those germs from spreading as much.
Open front seats are usually made of plastic or metal and are not typically used in residential bathrooms.
What are the different toilet seat materials?
Now that we have discussed the different types of toilet seats, let’s talk about the different materials that toilet seats can be made from.
The most common materials for toilet seats are porcelain, plastic and wood. However, they are also occasionally made from metal and specialty materials such as resin, polyresin, and acrylic.
7. Porcelain Toilet Seats
Porcelain toilet seats are a very common type of toilet seat. Conveniently, they’re made of the same material as the rest of the toilet, which makes sanitizing that much easier, since you can use the same cleaner on both surfaces and not worry about damaging one or the other.
8. Plastic toilet seats
Plastic toilet seats are a very popular type of toilet seat and are ideal for homes with young children! They are usually made out of a hard plastic called polypropylene. Polypropylene is a lightweight, durable material that is easy to clean, difficult to stain, and fairly inexpensive. Plastic toilet seats can also be made from thermoset or thermoplastic, which have scratch-resistant properties.
A downside to plastic seats is that some cleaners can remove the paint and cause wear. Another disadvantage is that they may not be as comfortable as other materials, e.g. B. when they are cold in winter.
9. Wooden toilet seats
Wooden toilet seats are exactly what they sound like – wooden toilet seats. Available in a variety of colors and finishes, they can add a touch of luxury to your bathroom.
Wood seats are warmer at any time of the year and tend to be more expensive than other types of toilet seats. However, they are not that easy to clean because wood is a porous material.
10. Bamboo toilet seats
Bamboo toilet seats are another type of wooden toilet seat. However, bamboo is a more sustainable option than other types of wood. Bamboo grows quickly and thrives without problems.
The downside is that bamboo toilet seats are usually more expensive than other types of toilet seats. They are also not as easy to clean as bamboo is a porous material.
11. Metal toilet seats
Metal toilet seats are not as common as other types of toilet seats and seem to be most commonly used in public restrooms. They are usually made of stainless steel, a durable and easy-to-clean material.
The downside to metal toilet seats is that they are unconventional and can be very cold. They can also rust over time if not properly cared for.
12. Special Materials
As mentioned, other materials such as resin, polyresin, and acrylic are also available.
These durable and easy-to-clean materials add an extra creative flair to toilets and can be an interesting part of your bathroom decor. The fun part about resin, polyresin, and acrylic toilet seats is that they can be infused with just about anything the mind can think of, from glitter to seashells!
Conclusion on types of toilet seats
Overall, there are many different types of toilet seats to choose from. There is sure to be a type of seat that suits your needs and budget.
When shopping for toilet seats, take your time and be sure to measure your toilet before you buy. This will ensure you get the correct seat size. And of course, think about the material and color of the toilet seat!
And if you are completely confused and have any questions, be sure to contact a seller. There are many options to choose from and they will help you find the perfect fit for your needs.
What kind of toilet seat do you prefer? Please let us know in the comments below. Have fun shopping!
What is a watermark toilet?
It is the Toilet cistern which will have “Watermark” stamped on the side of it. The Watermark standard only applies to the efficiency of a total unit. That means that a toilet dual flush valve (sometimes called a Toilet dual flush outlet valve) cannot have a watermark standard applied to it.
DIY Basics: How to Replace a Toilet Seat
That’s actually a wrong question, because “Watermark” is not a toilet brand. The watermark is actually an Australian standard that applies to sanitary products sold in Australia.
When you see “Watermark” on the side of an Australian toilet cistern, it means the toilet has been rated high enough to meet our specifications.
Watermark toilet dual flush valves
Dual Flush toilet valves do not require watermark certification as they are only one part of the overall toilet. It is the toilet tank with a “watermark” embossed on the side.
The Watermark standard only applies to the efficiency of an overall unit. This means that a watermark standard cannot be applied to a toilet dual flush valve (sometimes referred to as a toilet dual flush outlet valve).
Watermark toilet inlet valve replacement
Obviously, a “Watermark” brand toilet inlet valve isn’t a thing either. As previously mentioned, “Watermark” is an Australian standard and is also not a mark for toilet inlet valves.
If you realize you need a toilet fill valve and the only thing you can see on the side of the toilet is a watermark sticker, you have two options.
So how can I identify my toilet valve?
Alternatively you can click on the Inlet Valve tab at the top of our website at toiletspares.com.au. There you can browse our extensive selection of toilet filling valves.
Alternatively you can email or text us a photo of your toilet fill valve and we will either identify it for you or suggest an alternative toilet fill valve that you may require.
We have a large selection of Toilet Inlet Valves at competitive prices so you should be able to find what you need. Whether toilet inlet valves with floor inlet or toilet inlet valves with side inlet, we have a huge range.
We ship to Australia and New Zealand. We are incredibly fast shippers. If you order before 3pm (and usually before 4pm) we are almost certain to get the parts in the mail the same day.
If you live in the Express Post area and use our Express Post option, you should receive your part tomorrow.
Find us on Google Maps to see reviews from our many satisfied customers.
How do you release a quick release toilet seat?
Most modern toilet seats will have a quick release button to help you take it on and off easily. Press the button and lift the seat up. With a screwdriver, lift up the seat fixing caps to get to the bolts underneath.
DIY Basics: How to Replace a Toilet Seat
before you start
Needed tools:
adjustable wrench
screwdriver
Measure your toilet seat
To determine which toilet seat you need, you need to remove and measure your current seat.
Measure from the center of the two mounting holes to the center of the front of your toilet.
Measure the width of the bowl at its widest point.
You can use these measurements to determine which seat size you need. If you need to buy a new one, take a look at the excellent range of toilet seats available at Tap Warehouse
How to remove the old toilet seat
1. Press the button and remove it from the quick release
Most modern toilet seats have a quick release button that allows you to put them on and take them off easily. Press the button and raise the seat.
2. Remove the mounting caps
Using a screwdriver, lift the seat mounting caps to access the screws underneath.
3. Loosen the screws
Use your screwdriver to loosen both screws.
4. Remove the toilet seat fasteners
After loosening these, you can remove the screws and mounting kits on both sides.
Removing a traditional toilet seat
1. Remove the nut under the toilet
You should be able to find a nut under your traditional toilet. If it’s a wing nut you can remove it by hand, but if it’s a standard nut you’ll need to loosen it with a wrench or pliers.
2. Raise the seat
After removing the nut you should be able to pull the seat up and remove it along with the bolts.
Installation of the new seat
After you’ve removed your old toilet seat, it’s time to attach a new one. This guide will show you how to install a top mount toilet seat. For bottom mount seats see instructions below.
1. Attach the plastic plugs
Insert the two plugs that came with your toilet seat halfway into the holes in your toilet bowl.
2. Attach the hinge
Attach the metal washer to the top of the plastic plug and then add a hinge to the top of the washer.
3. Attach the screws
Insert the screws into the hole on the hinges and tighten them with a screwdriver.
4. Adjust the seat
Push the toilet seat into the quick release hinges and adjust until it is in the correct position. You may need to tighten the screws further at this point.
5. Mount hinge caps
When you have the saddle properly adjusted, remove the saddle from the quick release and snap the hinge caps onto the bolts.
6. Reattach the seat to the quick release
With the hinge caps added, all you have to do is reattach your seat to the quick release.
Installing a floor mounted toilet seat
Some toilets can be supplied with a bottom mounting kit, these are often easier to fit than modern top mountings.
1. Assemble the supplied fittings
Install the toilet hardware using the instructions that came with your toilet seat.
2. Fit the screws into the toilet
When your fittings are assembled, line up the screws and insert them into the holes on either side of the toilet.
3. Turn the nut underneath
Look behind your toilet and find the latch you just fell through. Thread the supplied nut onto this bolt by hand if it is a wing nut or with a wrench if it is a regular nut. Don’t overtighten just yet.
4. Adjust the seating position
Adjust the position of the seat until you are happy with it. Once you have done this you can now fully tighten the nut underneath and your seat is installed!
Now that you know how to replace your toilet seat, take a look at Tap Warehouse’s excellent range.
Can a self closing toilet seat be fixed?
You can make adjustments to the bolts that hold the seat in place to fix a loose toilet seat. The only reason you would need to adjust soft-close hinges is if your soft-close seat is not closing at the right speed. Lift the toilet seat straight up off the hinges from the upright position.
DIY Basics: How to Replace a Toilet Seat
Is there a standard toilet seat size?
Typical width: 14″ – 14-1/2″ Typical round length: 16″ – 17″ Typical elongated/extended length: 18″ – 19″
DIY Basics: How to Replace a Toilet Seat
However, your friends here at PlumbingSupply.com® are here to help with a quick guide on how to correctly measure a new toilet seat. You can either use your existing seat or, if you have a new toilet without a seat, use your toilet bowl. However, it is important to understand that these measurements and the measurements of the toilet seat you purchase may not always match 100% exactly. The majority of toilet seats available (even those sometimes included with new toilets) are made by secondary manufacturers, not the same company that made the toilet. Therefore, there may be minimal dimensional variations to allow the seat to fit a larger number of toilets.
All you need to get started is a tape measure, pen and paper. Then just follow the instructions below to make sure you get the right numbers. We have provided basic guidelines for most toilet seats. So if your numbers vary significantly from these ranges, or if you have an unusually shaped bowl, please measure again or contact us if you need further assistance. Additionally, you can always browse our full list of toilet seats for brand specific toilet seats, decorative toilet seats, or any other hard-to-find seat for older toilets.
Guide to measuring your existing toilet seat or toilet bowl
Are toilet seats a standard size UK?
There is no universal standard for toilet or toilet seat sizes in the UK. However, certain patterns have developed. The following combinations of toilet seat lengths and widths are relatively popular: width 35 cm, length 40-41 cm.
DIY Basics: How to Replace a Toilet Seat
the length of the toilet seat,
the width of the toilet seat and
the distance between the drill holes for the fasteners.
You can take these measurements either with your old toilet set or simply directly on the toilet itself. To determine the length, use a ruler to measure the distance between the center of the drilled holes and the front edge of the toilet. Then measure the width, which is the longest distance between the left and right sides of the toilet. Finally, all you need to do is measure the distance between the two mounting holes on the back of the toilet, again starting from the center of each hole.
Why is my soft close toilet seat not working?
If your soft-close seat isn’t working like it used to and you can’t adjust the hinges, you might have to fix it by replacing the hinge dampers with a new set.
DIY Basics: How to Replace a Toilet Seat
Why does my soft close toilet seat not stay up?
The most common reason toilet seats won’t stay up is because the seat was installed too far back towards the tank. Unscrew the seat, pull it as far forward as you can, and retighten. This should give your seat the extra angle it needs to stay upright.
DIY Basics: How to Replace a Toilet Seat
The most common reason for toilet seats not staying up is that the seat was installed too far back towards the tank. Unscrew the seat, pull it forward as far as possible and retighten. This should give your seat the extra angle it needs to stay upright.
Although this problem is the most common, it’s not the only reason your toilet seat could fall off. Read on to find out what problem you’re having and how to fix it.
3 reasons why your toilet seat won’t stay up
1. Seat too far back
As I mentioned above, this is probably the most common reason why toilet seats won’t stay up.
When a new toilet seat is installed, the angle of the toilet seat to the bowl must be more than 90 degrees for the seat to rest against the toilet tank. If the angle between the upright toilet seat and the toilet bowl is 90 degrees or less, the seat will keep falling down.
Luckily, this problem is pretty easy to fix.
Unclip the lid
Two screws attach your lid and seat to your toilet. Loosen these screws just enough to move the seat. You may need to use a wrench to start them.
If you are having trouble loosening the screws, you may need to use a screwdriver on top of the screw to keep it from turning.
Some toilets hide the tops of the screws under a small plastic cover, so check your toilet to see if you have these. When you do this, just gently open the cover to gain access to the screw. Then it just snaps shut again when you’re done.
Pull the seat forward
Once the screws are loose, pull the seat towards the front of the toilet as far as it will go. This should give you the extra angle you need to keep the seat from falling off.
Reattach the lid
Then just re-tighten those two screws and see if your toilet seat stays put.
If your toilet seat stays up after this quick fix, then woohoo! Well done! If not, don’t worry, you might have another problem. Luckily we have more solutions!
2. Toilet not level
Another reason your seat won’t stay up is that your toilet itself isn’t level.
This is pretty easy to check, take a bubble level, place it on your lid when it’s closed and see what it says. If you don’t have a level check your smartphone, some phones come with a level/measuring app.
If your toilet is tilted forward, you will need some toilet wedges or toilet washers. These little plastic guys look like miniature doorstops. They are used to slide under the bottom of your toilet to make it level.
They are fairly inexpensive and easy to install. Simply place them around the bottom of your toilet and use your fingers to push them in as far as possible.
Since you are having trouble with your toilet seat, you should position your shims around the front of your toilet. Hopefully this will give you that extra angle you need to hold the toilet seat up.
Be careful not to push the washers in too hard too quickly. There is a wax ring under your toilet that prevents the nasty water from escaping. If you push too hard or lift too far you could move or damage this ring and then you would have a bigger problem on your hands.
Once you’ve installed your shims, recheck your toilet with the level. Hope it’s just right.
If your toilet seat still won’t stay up after this, you may need to combine a few of these solutions to get it right.
3. Toilet lid too thick
The last reason why your toilet lid may fall off is that your lid and seat combination is too thick. As a result, the seat sits just under 90 degrees and falls over.
Something that could cause this is if you have a toilet seat or lid cover. You know, the ones that look like a shag carpet.
If you remove the cover and it no longer falls off, then you have your solution.
If you don’t have a cover, you may need to buy a new toilet seat or maybe just a new lid that’s thinner.
Before you make that investment, though, try pushing the lid on your toilet tank back as far as possible. That little shift might be all you need to keep your toilet seat upright.
How do I fix a wobbly toilet seat?
While boys can be annoyed by an upstanding toilet seat, there is nothing more annoying for ladies than sitting on a wobbly toilet seat.
There are two main reasons why a toilet seat can wobble.
1. Loose screws
Loose toilet seat bolts can have many causes including daily wear and tear, debris under the bolts, etc.
To fix loose screws, you should remove the screws first. You may need to flip up a small plastic cover on top of your toilet seat to access the screws.
Use a screwdriver at the top of the screw to loosen it. If it spins without loosening, you need a wrench or pliers. Use this to hold the nut on the bottom of your toilet so you can loosen the bolts.
After removing the toilet seat, clean the area where the screws were located to remove any debris that may have collected there. Be sure to check the underside as well.
This cleaning may be enough to solve the problem. So at this point, all you have to do is reattach your toilet seat and see if you’ve fixed the problem.
If your toilet seat loosens again after this quick fix, try getting some rubber toilet seat washers. These little guys help give your seat the extra support it needs to stay in place.
To install them, remove the toilet seat in the same way as before. Then simply place the washers between the top of the bolt and your toilet. Secure your seat and you should be good to go.
2. Wrong seat size
Another reason you might wobble on your porcelain throne is if you have the wrong size toilet seat.
Each toilet seat has spacers on the bottom so your toilet seat doesn’t rest directly on the toilet.
If your seat isn’t the right size, these spacers could slide in or out of the rim of your toilet and give you a wild ride.
The main reason is that someone bought the wrong toilet seat. Toilets come in two shapes, round and oblong.
Just like you can’t fit a square peg in a round hole, a round toilet seat won’t work on an oblong toilet.
This problem really has only one solution, you need to buy the right size toilet seat. Take a picture of your toilet and/or take your toilet seat with you when you go to the hardware store.
Once you have a new seat, simply reattach it to your toilet and enjoy a wobble-free experience.
related questions
Can I have my toilet seat close gently?
You can make a toilet seat close smoothly by installing a soft-close toilet seat. Soft close toilet seats are designed to prevent slamming by slowly lowering the seat onto the bowl. Alternatively, you can use rubber bumpers or lid covers to soften the impact when closing the toilet.
How do you adjust a toilet seat?
You can adjust a toilet seat by loosening the two screws that attach it to the toilet bowl. Once the screws are loose, reposition your toilet seat in place. Then re-tighten the screws while holding the seat firmly in place.
How to release 3 different types of toilet seats.
See some more details on the topic bathstore watermark toilet seat here:
Bathstore Toilets for sale – eBay
Bathstore Toilets. Se Refine Panel. Shop by category. Toilets & Bets; Toilets; Toilet Seats · Toilet Parts & Attachments · Bets · Bet Taps …
Source: www.ebay.co.uk
Date Published: 5/2/2021
View: 523
Cannot find a replacement toilet seat. – MyBuilder
http://www.bathstore.com/products/watermark-soft-close-wc-seat-2707.html. Regards Matthew @ MLS Plumbing Solutions. 2016-04-18T08:00:02+01:00.
Source: www.mybuilder.com
Date Published: 1/27/2021
View: 9075
ORIGINAL BATHSTORE WATERMARK SOFT CLOSE TOILET SEAT AND COVER WITH FITTINGS 536969 ORIGINAL
JavaScript seems to be disabled in your browser. In order to use our website optimally, activate Javascript in your browser.
How to Replace a Toilet Seat in 3 Simple Steps
Replacing a toilet seat is pretty quick and easy. It only requires basic DIY skills and as long as you have the right equipment it can easily be done by a beginner.
The tools you will need to complete this job are:
A flathead or Phillips screwdriver
Tongs
Your brand new toilet seat
Please note: the process may vary depending on which new toilet seat you have chosen and what type of toilet you have. It is always best to consult the installation guide before attempting any work.
To replace your toilet seat, you must:
1. Clean your existing toilet and toilet seat
Toilet seats are often a host to germs, and since you’ll be touching your toilet a lot during this process, it’s important to make sure you’re doing so in a safe and hygienic manner. Put on a pair of rubber gloves and thoroughly clean your toilet and existing toilet seat with disinfectant and detergent.
2. Remove your old toilet seat
This process depends on what type of toilet seat you have. Some modern toilet seats have a button between the hinges that connect the seat to the toilet. If your toilet seat has this button, simply press it and lift the seat.
If you have a standard toilet seat, you will need to loosen the screws with a screwdriver while holding the nut underneath with pliers. These screws are located at the back of the toilet bowl where the seat connects to it. Once you’ve done this, you should be able to take off your existing toilet seat right away.
3. Install your new toilet seat
Again, this process largely depends on what type of toilet and toilet seat you have.
Some toilet types require you to remove the cover plate and then unscrew and remove the old hinge bracket before positioning the new hinge bracket over the seat mounting holes.
To install the new toilet seat, insert the new nut and retainer through the holes in the toilet bowl and then tighten with a screwdriver before installing the new toilet seat.
For more traditional toilet types, simply place your new toilet seat over the two existing holes in the toilet bowl and then insert the bolts and hand tighten the nuts. After that, hold the nuts with pliers and tighten the screw heads with a screwdriver.
Make sure not to over tighten the screws at this point or you could damage your new seat. Next you can put the plastic screw head covers back on the screws and your new toilet seat should be secure.
DIY Basics: How to Replace a Toilet Seat
How to replace a toilet seat
Installing or replacing a toilet seat is a fairly simple task. Whether you are replacing your toilet seat because it is old or damaged, or you want a new style; All you need are some basic tools.
Installing a toilet seat is often one of the easier and quicker DIY jobs to do in your bathroom and can be completed in minutes.
Read on for our full guide explaining the steps of the process…
Why should I replace my toilet seat?
Toilet seats can be replaced for a number of reasons. These may include the seat being broken or cracked, the fasteners may have disappeared causing it to wobble and move when you sit on it, or you want a new style.
Read more: Update your bathroom on a budget
If you’ve had a new bathroom installed the seat will likely be made for you, but if not this is another reason to install a seat in your loo.
Do all toilet seats fit the same?
No, not all toilet seats fit the same as toilets come in different shapes so you need to check yours before buying.
Read more: What types of toilets are there? Buying advice for toilets
There are three types of toilet shapes commonly found in UK homes. These are round, D-shaped and square seats. Another popular feature is a soft-close seat. So if you prefer this, you need to measure correctly to ensure this type of seat fits your toilet.
Replacement toilet seats can usually be fitted to older or non-standard toilets. However, the seat must be supported at the contact points or hinges.
Most toilet seats are oval in shape, although some have a more contemporary square or D-shape. So it’s important to keep this in mind when looking for a replacement in a store or from the original manufacturer.
Before you buy a seat, there is something important to do…
How to measure a toilet seat
This is arguably the most important part of replacing your toilet seat – you don’t want to buy one that doesn’t fit.
Are toilet seats a standard size?
No, due to different toilet styles, there is no standard size for all toilet seats. To find the best seat for your toilet, you need to measure your toilet. Read how to do this below.
There are important measurements you need, although most seats are adjustable to accommodate most common toilet bowl shapes. The measurements are:
The distance between the mounting holes – where the screws are located. This is often a standard 155mm measurement, but it’s worth checking
The width of the toilet bowl at its widest point
The length from the front of the shell back to the two seat mounting holes
With these measurements you can be sure that you are buying the right size toilet seat.
Do I need to take any safety precautions before changing my toilet seat?
Toilets are an obvious place for harmful germs to grow and can be a source of potential infection, so you should take precautions before you begin.
Always wear rubber cleaning gloves when changing a toilet seat. Ideally, clean it before removing it. After removing the seat, thoroughly clean your entire toilet. Use an antibacterial spray that you can buy at most stores.
Use an antibacterial hand wash after replacing your toilet seat to ensure you’ve removed any harmful bacteria.
What tools do I need to change a toilet seat?
You’ll need pliers or an adjustable wrench to remove the nuts that attach the seat to the toilet—these are often wing nuts.
You may also need a flathead screwdriver to remove any plastic caps covering the nuts. Most of these tools can be found in a garden shed or bought for little money at most stores.
Depending on the seat you buy, it may come with a kit to attach it. If you’re just replacing the hardware like the nuts and not the whole seat, you’ll probably have to buy the parts yourself.
Some newer toilets may not have traditional screw-on seats, but instead have a push-in seat. So it’s best to check before you buy a replacement.
How to remove an old toilet seat
Most toilet seats attach to the toilet with hardware. These are held together by two bolts, usually hidden behind plastic caps on the back of the seat.
You may have to crouch or stand on the ground to access it properly.
If there are plastic caps over the nuts, use your flat head screwdriver to remove them. This can be more difficult with older seats if they have been there for a long time. Working your way around the cap, without being too rough to damage the toilet itself, carefully remove the caps.
Once you remove the caps you will see the top of the screws with wing nuts holding your seat in place. These nuts are often made of plastic, but can also be made of metal – depending on the age of the seat. Use your pliers to loosen the nuts, then remove them by hand.
The seat should then lift off, but depending on the brand you may need to unscrew it with your screwdriver. If it’s stiff or too rusted to lift off on its own, spray some WD-40 to lubricate it and wait up to 10 minutes before lifting the seat off.
If they’re still stuck, you may need to carefully saw them off with a small hacksaw.
Some toilet seats vary in how they are held in place, but most work in a similar way. If your seat is different, take a look at the hardware and you should be able to figure out how to remove it.
It can be difficult and not the most pleasant work, but it shouldn’t take long. Just remember the process for next time.
As mentioned above, after removing your old toilet seat, give the entire toilet a thorough cleaning with antibacterial spray.
How to install a new toilet seat
Once you’ve removed your old seat, it’s time to install the new one. With the new seat you will receive hardware, including manufacturer’s instructions for installation.
Essentially, installing a new toilet seat is the reverse of the removal process.
First, line up and attach the new fittings – by inserting the screws through the toilet’s mounting holes. Make sure your seat sits evenly on the perimeter of your toilet bowl and center it. Use your hands or pliers to secure the wing nuts once you are happy with the position of the seat.
Be careful not to over tighten them as you may want to adjust them once the new toilet seat is in place. Additionally, plastic bolts – if they are – don’t need to punish much before either yielding or breaking.
You can also have rubber washers that you can place between the nut and the toilet to act as a cushion.
You will do this on both sides of the seat as there are two bolts so two wing nuts that need to be tightened altogether.
If plastic caps were included with the new toilet seat, snap them into place by pushing down on the screws onto the wing nuts.
By following these steps you should be able to replace your toilet seat quickly and easily.
toilet seat designs
No matter the size or style of your bathroom, you’re guaranteed to find the right toilet seat for your home. Available in a variety of shapes and sizes and a range of colours, from classic white to bright pink to a seat with a beautiful animal design, there is a toilet seat for every taste.
Olli Lyon
Ollie is a self-trained handyman who has a particular love for kitchen and bathroom renovations. In his free time, Ollie enjoys cycling and hiking.
We love seeing your bathroom makeovers and sharing them on our Instagram page – if you’ve had a Plumbworld makeover, tag us in your photos to be featured!
We’d love to know, so why not share your favorite designs with us on social media?
Find us at:
Facebook | Twitter | Instagram | Tiktok | pin rest
Alternatively, sign up for our newsletter to receive the latest offers, latest product launches and advice.
Are you planning a new bathroom or kitchen? Shop online at Plumbworld for guaranteed lowest prices and next day delivery.
Don’t forget to read the rest of our blog for more bathroom and kitchen tips.
Related searches to bathstore watermark toilet seat
Information related to the topic bathstore watermark toilet seat
Here are the search results of the thread bathstore watermark toilet seat from Bing. You can read more if you want.
You have just come across an article on the topic bathstore watermark toilet seat. If you found this article useful, please share it. Thank you very much.
