Gutter Drip Edge Extender? The 165 New Answer

Hi. I just had my roof replaced and I believe there are some issues that need to be addressed. I’ve spoken to the contractor about these things and they’re trying to work with me, but they don’t really seem to know what to do.

The gist of it is that they installed the new roof without removing the entire existing drip edge (in the shape of an L, 1.5″ wide on either side of the bend) or the gutters, and then installed a NEW drip edge (in the shape of a T , 2″ on either side of the bend) onto the old drip edge. I know for a fact that they put the new drip edge on top of the old one on all the eaves (where there are gutters). It seems they remove the old drip edge at the rakes have that I can reach on the ladder but I can’t access the higher parts to tell if this was done consistently In connection with this they had taken the metal mesh leaf guards on the gutter and nailed them under the shingles The leaf guards used to not be attached to the roof and I removed them once to clean the mud so I asked them to fix the leaf guard situation and that’s when I could see what they were doing with the drip edge n had made.

So:

Are there circumstances where it’s okay or advisable to install over the old drip edge? (In this case the old drip edge appears to be inside the gutter and the screws pass through the drip edge and gutter to the fascia. (One suspects this is why they decided not to use the original drip edge to remove…) If the answer to question 1 is “no”, what should I do in this situation? The roofers are not comfortable removing/reinstalling the gutters…but now that the new roof is installed, they obviously have more limited access to remove parts of the old drip edge (by just unscrewing some of the screws) than if they had done so on the job, a roofer should normally inspect existing gutters before work to know what he has to plan for at work?And would a roofer usually remove or install gutters as part of the job (provided he gets paid to do it) or does he generally advise the homeowner to hire a gutter professional to do this job while the job is being done? The shingles rise a bit (i.e. don’t end up on the same slope as the roof…perhaps so that the water would miss the gutter?) and are a bit wavy. Is the likely cause of this due to the dual drip edge?

Thanks for the guide. To be clear, I’m not trying to get the roofer to do more work for no money. (If the gutter stuff should have been on sale and they missed it, but can now address it with a fair additional cost, I’m fine with that. What worries me more is that there’s no reasonable way to address this after fact) .

When it comes to roof fitting and protection, drip edge and gutter skirt are both terms you should know. However, we understand that not everyone is a professional local roofer and that words like drip edge, metal surround and gutter skirting may not be in your normal vocabulary. Good luck to you, that’s what we’re here for! In this post, our team of roofing specialists at Quality Exteriors will break down the drip edge vs gutter skirt and the difference between the two.

Whether you have storm damage or are simply interested in improving your home, we have a team of dedicated home builders ready to meet your specific needs. QEI specializes in providing roofing, siding and window services for the Shreveport-Bossier City areas. We also offer free appraisals and inspections of your home or business according to your needs. With Quality Exteriors you are guaranteed to receive the highest quality of service and workmanship.

What is drip edge?

There are many different things that can contribute to water entering your home and causing damage. One of the most common causes is a lack of proper protection along the roof shingles where your roof edge meets your home. This is where a so-called “drip edge” comes into play. The drip edge is a type of metal shroud that prevents moisture from entering at this vulnerable point. Its purpose is to direct water away from interior areas where it shouldn’t be, helping to protect your existing roof from damage and possible rotting from water ingress.

Drip edges are an important part of the home but are not always installed during the initial construction of a home. Some states require the drip edge to be installed, while others highly recommend it.

A roof drip edge is a T-shaped piece of metal that is installed along the perimeter of a home’s roof and essentially forms a watertight seal around the edge of the roof. The front of the metal drip edge must overlap the gutter to prevent water from falling into the gaps. Its purpose is to filter water out of the roof by directing it away from the face and into the gutter. This will prevent rotting of the bulkhead holding the gutters and prevent them from falling onto your roof system.

Drip edges can be virtually any color, but the most common colors are neutral colors like white, black, and brown. It is also possible to color match your roof shingles or gutters to the drip edge for a more distinctive look. Some people may even choose to use an accent color for their metal drip edge to “pop” the roof or to complement other parts of the home like shutters or doors.

Why does rain drip between the gutter and gutter?

5.07 k Facebook Twitter LinkedIn Pinterest WhatsApp Correo Copy link Your browser does not support automatic copying, please select and copy the link in the text field and paste it where you want.

Rain gutters can save you a lot of headaches. A good rain gutter system will help you protect your property and investment in a number of ways, simply by carrying the water that falls during a storm so it doesn’t damage your foundations, walls and many other parts of the home. Installing residential gutters can be tricky because the gutter must match the dimensions of your roof. Even after you’ve seemingly followed these measurements, it’s common to find instances of water leaking out from behind the gutter. There are ways to prevent this outcome, but first we need to understand why it happens.

How to identify a leakage problem?

If you stay on schedule with your maintenance routine, it’s easy to identify a problem and even the source of a leak in time. Aside from damage to the gutter system (cracks, stains, corrosion, etc.), the location of a puddle of water is an indication. It is relatively easy to spot a seam problem as the leakage occurs around the seam itself. Now, if the water isn’t dripping from a certain part of the gutter, e.g. B. the end caps or above the downspouts, it can be more difficult to identify the source of the problem. For example, rain drips between the gutter and the gutter. This is a fairly common consequence of a faulty installation, but the immediate cause isn’t always the same.

Is your gutter loose?

Your gutter may be misplaced, either due to a calculation error during the installation process or because it has become unstable over time. Rain gutters need to be 2-3 inches from the edge. If it’s too far down, there’s an open gap for the water to seep through. In these cases, the gutter can sag and tilt away from your roof, cutting off the water’s path after it reaches the edge of the roof. Loose gutters are often the source of rain dripping between the gutter and the gutter. In some cases, you can restore gutter stability by strengthening the bracket’s grip, but replacing the gutters in advance is the best way to prevent the drip problem from getting worse over time. However, if the gutter is truly misaligned, there is no other way than to request a replacement from a professional installation company. Now there are other reasons why water can seep between gutter and gutter. To find them, you need to look at your entire roof area.

Check your drip edge

The drip edge is a piece of sheet metal, usually aluminum or vinyl, that acts as a barrier and covers the gap between the gutter and the roof shingles. It allows the water to fall straight into the gutter without running off the back. If water drips between the gutter and gutter, it may be because your drip edge is too flat. It should slope down slightly to allow water to flow naturally from the roof to the gutter. If the drip edge needs to be replaced, you can make the repairs without removing the gutters, but depending on your configuration, you may also need to replace the headboard.

Watch out for leaks

5.07 k Facebook Twitter LinkedIn Pinterest WhatsApp Correo Copy link Your browser does not support automatic copying, please select and copy the link in the text field and paste it where you want.

Leave your comment Comments 0

Leaks and spills can be disastrous if not dealt with in a timely manner. First, they ruin the exterior appearance of your home as the water rots many parts of the home and peels the paint off your walls. As you can probably imagine, this will leave a bad impression on guests and passers-by alike. After all, leaks will degrade your siding inside and out, and no one wants to find the visible effects of a leak inside the home. Excessive moisture not only leads to foundation problems that would compromise the entire structure of the building; it will also encourage the growth of mold and mildew and this poses a significant health risk to everyone in the home. As mentioned above, it definitely helps to gauge the direction the water is dripping from. When blockages slow the flow, water overflows the gutter. This particular problem could be solved after cleaning out the gutter if you find the clog early enough to avoid structural damage. In other cases, the problem is not with the gutter at all. If you see signs of deterioration on your shingles or water stains on multiple parts of the roof surface, you can probably guess where to focus your efforts. In these scenarios, the water drips from the parapet and straight down the reveal, with nothing stopping it from seeping into your walls. Here are other general recommendations: Even if your gutters are working properly, you still need to check them regularly. Keep an eye on your dashboard at every inspection. If you see signs of rot, you should take a closer look to find an underlying problem. And always remember that the expertise of a professional contractor is the best way to overcome misaligned gutters without risking a new incident after you’re done. Professional gutter services have guarantees to avoid losses if the materials of the contractor’s performance do not meet the requirements. Install the best rain gutters to avoid a drip problem. Rain Gutters Solution has everything you need to ensure you get the most durable gutters and the best result for your home. We understand all the factors that go into the installation process and how to deliver the expected results quickly and efficiently. You can call (305) 270-7779 or fill out the contact form on this website to schedule an appointment. Let Rain Gutters Solution become your home’s greatest ally. If you found this article helpful, let us know in the comments section below. Likewise, feel free to share it using the sharing options below. Would you like us to cover another topic of your interest related to rain gutters? If so, please like and follow us on social media and post the topic you want us to discuss on one of our social media profiles: Facebook @RainGuttersSolution, Twitter @Gutterssolution and Instagram @RainGuttersSolution

Should gutters be longer than the roof?

1.25 k Facebook Twitter LinkedIn Pinterest WhatsApp Correo Copy link Your browser does not support automatic copying, please select and copy the link in the text field and paste it where you want.

There are a few things to consider when installing gutters. Even before the actual installation of your rain gutters, there are many things to consider, from the material to the right gutter profile. Size and dimensions are among the crucial factors that should be discussed in advance as they are essential for the gutter to function properly. With this in mind, it can be difficult to keep track of all the measurements associated with the installation process, especially when you don’t have a professional contractor leading the whole thing.

Why install rain gutters?

Rain gutters are not a luxury. They are a practical asset and as such their installation must be handled with care. A rain gutter system catches the rain falling from the roof onto your property and directs it directly into a drainage path. No matter how intense a rainstorm, the rain gutter will keep water from pooling on your foundations and around the floor of your home, preventing costly structural problems that could compromise the stability of the entire building. This also helps prevent mold and mildew from growing on your foundations, allowing you to protect the integrity of your home at all ends and protect the health of its occupants. While guttering is a straightforward process in most cases, there’s no way to avoid all the sizing specifications that come with adding a gutter system to an existing design. A miscalculation not only renders the gutter ineffective, but can also result in serious damage to the roof and walls of the building.

Defining the size of your gutter

The gutter should protrude slightly over the roof shingles. 3/4 the width of your gutter should extend past the shingles to catch all water and direct it properly down the downspouts.

The gutter should be between 2 and 3 inches from the edge of the roof. The exact number depends on the roof pitch and the placement of your downspouts.

The gutter should be slightly sloped. It should slope about 1/2 inch every 10 feet to the downspouts. Gutters can be as long as they need to be to fit a building, but on average, the length of a gutter is somewhere around the 20-foot mark.

The gutter should sit behind the drip edge to prevent water from sliding through the gap and into your siding.

On the one hand, they need to be positioned just right to catch the water rolling down your roof. It’s actually quite common for homebuilt gutters to leave too much of a gap between the roof and trim, resulting in spills, peeling paint and possible roof/fascia damage. Because of their size, a gutter can range in width from 4″ to 8″ depending on the case, with 5 and 6 inch aluminum gutters being the most common options in most modern homes. The architecture of the building and the local climate play a role in defining the right size to store as much water as possible. Expanding on the advice above, here are important measures to keep in mind:

What happens if I don’t do the measures correctly?

If you skip any of the steps above, the main problem will be that all the water will slide down behind your gutters. Its walls would be soaked after every storm, and nothing would stop the progressive damage to the floor and foundations. Another problem associated with incorrect measures is that the water does not flow as it should and instead affects your roof to follow the drainage path of the gutter. If the gutter is not attached to the drip edge, the gutters will not properly redirect it to the downspouts. At worst, this could rot your fascia and you would have to cover major repairs to your roof, let alone completely replacing your gutters. A gutter that is too steep is a common result of DIY methods, as are too many seams, which could cause your gutter to leak in multiple places. Errors when screwing on the folds or incorrectly setting the hangers lead to the gutter becoming unstable after a while and tipping forward or sagging.

Why hire a professional installer?

1.25 k Facebook Twitter LinkedIn Pinterest WhatsApp Correo Copy link Your browser does not support automatic copying, please select and copy the link in the text field and paste it where you want.

Leave your comment Comments 0

As you can see, installing a gutter properly is harder than it looks, not to mention a potential safety hazard, if you only know the process at a surface level. A professional installation service will provide the materials and equipment you need, saving you time while ensuring the best quality. More importantly, they identify all of the structural factors that come with your property and adjust their methods accordingly. Your contractor knows the meaning of each measurement and the outcome if a gutter does not exactly match those measurements. Through a portable machine that builds bespoke gutters on site, the installer creates a durable, seamless gutter system and uses all the tools needed to ensure its stability once it is attached to your roof. Get the best gutters in the South Florida area and protect the value of your home. Rain Gutters Solution is here to help you every step of the way, so come join us if you are looking for the most experienced installers to install your gutters. You can call (305) 270-7779 or fill out the contact form on this website to schedule an appointment. Let Rain Gutters Solution become your home’s greatest ally. If you found this article helpful, let us know in the comments section below. Likewise, feel free to share it using the sharing options below. Would you like us to cover another topic of your interest related to rain gutters? If so, please like and follow us on social media and post the topic you want us to discuss on one of our social media profiles: Facebook @RainGuttersSolution, Twitter @Gutterssolution and Instagram @RainGuttersSolution

The 5 Best Solar Generators (2022 Review) A solar generator gives you backup power from the sun in case your power goes out. In this review, the This Old House Reviews team researched the five best solar generators on Amazon to help you find the right product for you and your home. The products included in this article are available at various hardware stores, local hardware stores, and online retailers such as Amazon.

Roof installation is a tricky business at the best of times. The use of metal roofing panels presents unique challenges that must be considered to avoid problems down the road.

Metal roofs should have a 1 inch overhang due to the increased water velocities as rainwater flows down its smooth surface towards the gutters. Gutters should also be larger to accommodate the up to 40% more water per second that quickly pours into their metal tubs.

Today I’m going to focus on the relationship between your roof and your gutters. We pay particular attention to how much overhang metal roofs should have over gutters. I also have a quick guide to installing metal roofing panels that might come in handy and help you understand your overhangs. Let’s start.

How much should a metal roof protrude beyond gutters?

The importance of gutters cannot be overstated. Gutters are essential to protecting a building’s foundations as they safely channel water to prevent soil erosion at the base. Gutters also protect building cladding from direct exposure to dripping water.

Metal roofs should not overhang gutters by more than 1 inch because water will flow faster over their smooth surfaces compared to asphalt, wood, or stone shingles. Larger 6 inch gutters are also recommended to accommodate the increased water flow.

Just as important as the presence of gutters is the positioning of the edges of the roof in relation to them. For gutters to be effective, the edge of the roof (or overhang) must be positioned so that all rainwater on the roof can seep into the gutters.

Keeping leaves, sticks and debris off your gutter downspouts is extremely important to keep them clear and clean. I recommend these cheap and effective downspout screens from Amazon to protect your primer from the corrosive effects of water.

Overhangs depend on gutter size

Too much overhang and water will shoot over the gutter and end up right next to the building. Too little and some water can fall behind the gutter and drip down the walls.

The overhang must also leave enough space for the gutters to be cleaned, especially if they are small. Too much overhang can make it difficult to scoop out debris like leaves and twigs.

In the US, most domestic gutters are either 5 inches or 6 inches wide. The former is the standard for most homes with traditional roofing materials such as clay and asphalt.

However, the rapid flow of water on a metal roof may necessitate a switch to larger 6 inch gutters that can hold up to 40% more water. Therefore, larger gutters can accommodate larger overhangs than smaller ones.

How much overhang can a roof have over a gutter?

Roofing material is important

Well, that depends on a few factors, the main one being the particular roofing material.

Clay tile and asphalt shingle roofs have enough friction to slow the flow of water even in heavy rain. This makes it possible to let the roofs protrude further over the gutters.

Typically, non-drip shingles should have an overhang of about 1-1½ inches over a gutter. With drip edge trimming you can reduce your overhang to about ½ – ¾ inch. From 2012, according to the requirements of the International Building Code, shingle roofs must be equipped with drip edge plates.

Metal roof panels, on the other hand, are a completely different matter. Due to its (usually) smooth surface, metal hardly slows down the flow of rainwater. Depending on the pitch of the roof, rainwater runs down metal plates at a higher speed than on clay or asphalt.

For this reason we recommend that you allow your metal roof to extend 2.5 cm over the gutters. The extent of the overhang depends on:

Your local climate and environment

The size of your gutters

The type of metal roofing

The slope of the roof

The size of the roof

Roof pitch plays a role in overhangs

The size and pitch of your roof can also affect the momentum of water flow, which directly affects the amount of overhang over gutters. Large pitched roofs do not require as much overhang as flatter roofs with smaller areas.

This is compounded when choosing metal roofs due to the increased water flow. With 40% more water in less time, typically for a metal roof, increasing the pitch also increases the speed at which the water moves.

Climate and the corresponding weather influence the dimensions of the roof

Your local climate is another consideration. If you live in an area where it often rains heavily, you should opt for a shorter roof overhang. Also, if you live in a very windy area, a short overhang is a good way to go.

Strong gusts of wind are quite capable of tearing a metal roof panel out of position. Too much overhang only increases that risk. For this reason, drip edges are recommended in areas prone to wind-driven rain, hurricanes, and tornadoes.

Read more of my articles on lawn and home care here…

How do I install a metal roof panel with existing gutters?

The DIY rooftop installation might seem daunting at first, but it’s pretty easy. Metal roofs are becoming increasingly popular these days due to their durability, aesthetic variations, and lower long-term maintenance costs.

Step one: measurements

The first step of a roof installation is the measurement. You need to know the specific dimensions (length, width, pitch) of your roof sections before ordering your materials. Safety is paramount here, especially when climbing the roof.

Determining the pitch for metal roofs is crucial

You also need to determine the pitch factor of the roof. This is done by:

Multiply the slope by itself Multiply the run by itself Add the answers above Find the square root of the total Divide the square root by the run

In short, the slope factor of the roof = √(rise2 + rise2) ÷ rise.

The slope factor is then used to determine the area of ​​a roof section. To do this, the unfinished roof area (length times width) is multiplied by the value of the slope factor. Repeat for each section of the roof.

At this point you can determine the total area of ​​your roof. For this purpose, the area values ​​of all sections are added. The total square footage is the size of the roofing material you need. We suggest you get 5-10% extra material in case of waste or measurement errors.

Step 2: Setting up the site

Once you have received your roofing material, you need to set up a construction site. Your construction site should include scaffolding, a ladder, trash cans, and a tool platform.

Speaking of tools, you will need:

A staple gun

A drill and drill

metal scissors

1 ¼ inch roofing nails

Metal roofing screws

wood screws

Step 3: Remove or keep the existing roof

After the construction site has been set up, you are faced with the decision: remove the existing roofing or lay the sheet metal over it.

We recommend removing the existing roof. Be careful not to rush this task as it is quite risky. Protruding nails drop tiles and the ever-present risk of falls are just a few of the things to worry about here. You can either throw the tiles in the bin or store them elsewhere for later use.

Make sure you remove your roof on a dry day. A building without a roof is very susceptible to water damage.

If you remove the roof, you can also change or adjust your gutters to be compatible with the new roof panels. You should also repair underlying wood paneling, vents, and insulation before installing the new roof.

We advise you to add a new insulation layer and a breathable membrane. This layer protects the wood sheathing in the event of water spilling over the roof panels. The insulation should be secured with a staple gun or nails.

Step 4: Installing the Roof and Flashing

Although the drip edge is still optional for metal roofs, we recommend that you use it, particularly to minimize overhang over gutters and to protect underlying timber panels.

Metal roof edging helps with overhangs

The metal strips that will serve as the edge flashing need to go around the edge of the roof and be fastened to the sub-roof with 1¼” nails. The edging needs to overlap the gutters by about ½ – ¾ inch.

After the edging is in place, you can start assembling the metal panels.

Install metal plates on the same overhang as the flashing

Always start at the point with the greatest distance between the peak of the roof and the eaves. The first metal plate sets the tone for how the others will sit on the roof. Make sure this panel is square to the edge of the roof (or edge flashing if applicable). The overhang of the panel must be exactly the same as that of the border.

The panel must be attached to the underlying wooden formwork using flat head screws with rubber seals. Drill down from the roof top and drill holes and fasten the screws at 12 inch intervals. Avoid over tightening as this could damage the rubber seals.

Once the first panel is in place, attach the others in a similar fashion. Each panel must overlap an adjacent panel by at least 2.5 cm to prevent water leakage. You can also use silicone sealant to secure the panels together even better.

When the entire roof is covered with panels, you need to add the roof flashings. These thin strips of metal are made to cover the gaps between panels in different sections of the roof, as overlapping is not possible. You may need to bend the strips into a “V” shape to fit over ridges.

The flashings must be secured using the same washer screws used for the panels. Working from the top, use a row or two of screws for each flashing.

Once the panels are in place, you need to thoroughly inspect your work. Make sure each panel is tight and protrudes continuously. Also check for loose screws and misplaced turn signals.

The final touch on how far metal roofs should protrude over gutters…

With the popularity of metal roofing and the relative ease of their installation, many aspects can be unclear to the do-it-yourselfer. There are many extraneous aspects that metal roofing requires expertise that are not applicable to shingled versions.

There are waterproof seals and ridge insulation as well as different dimensions for gutter overhangs. The overhang for most metal roofs should not exceed 1 inch, but this also depends on pitch and flashing.

Keeping water away from a foundation is one of the most important jobs of roofs and gutter systems. Installing the right size and with the right overhang is critical to the longevity of your home.

Here are some more items I recommend…

references

https://www.hunker.com/13402455/how-much-roof-overhang-for-a-metal-roof

https://www.wikihow.com/Install-Metal-Roofing

https://www.youtube.com/watch?v=SetghGeDP1Q&ab_channel=DaltonRoofing

Print/Save as PDF

We’ve all seen overflowing gutters, but we don’t think about the damage they can do. They can cause a leak in the walls of your home or even affect your foundation with all that overflowing water from all that debris clogging your gutters.

To avoid this, you can call a local roofing company to clean them, or you can do it yourself. You don’t want to do it yourself because of the safety risk, and you don’t want to constantly pay someone to clean them.

Wouldn’t it be great if there was an option that can prevent dirt from getting into your gutters in the first place? Luckily there is, and we’ll break it down for you.

The Bill Ragan Roofing team has been helping Nashville residents with their gutters since 1990. We strive to offer you the best possible experience during a stressful time. Whether you need to clean, replace or install your gutters, you can count on us.

At the end of this article, you’ll learn what gutter guards are, what types they are, how much they cost, and more.

What are gutter guards?

Gutters control where water flows after it leaves your roof. However, if they are full of dirt, the water coming off your roof has nowhere to go.

This can lead to a variety of costly problems. So how do you avoid this happening to you?

The first option is to have your gutters cleaned routinely as part of roof maintenance. The second option is to install something above them to catch or shed the debris.

This is where gutter guards come into play. Gutterguard is a loose term used to describe anything that goes over your gutters to catch or shed dirt coming down from your roof.

What types of gutter guards are there?

While the term gutter protector is used loosely to describe a gutter cover, there are 2 “styles” (types) of gutter protectors. The 2 types are gutter guards and gutter helmets.

gutter guard

Gutter Guards consist of a mesh of wire (stretched aluminum wire or powder coated steel wire) that is passed over the top of your gutters.

This type of gutter guard allows water to flow down your gutters as usual while the mesh screen catches debris.

The problem with this type of gutter guard is that small debris (like maple tree helicopters) can slip between the wire and fall into your gutters. But for larger debris like oak leaves or pine needles, a gutter screen should work just fine.

gutter helmet

Gutter helmets have two different types to choose from. One that attaches to the existing gutter and another that is a single piece (gutter and gutter helm roll formed together) such as LeafGuard.

Gutter helms work by using static water to roll water coming down from your roof back up the gutter while debris rolls off the gutter helm onto the ground. If dirt gets in the gutters you will have to call the company that installed it as it is really difficult to remove.

The disadvantage of this type of gutter protection is that when it starts to rain, water can run down the gutter helmet before the static builds up. This is not an ideal situation (especially if you have a basement) as the water will run down and affect the foundation of your home.

How much do gutter guards cost?

I can’t give you exact numbers on the cost of gutter protectors as each company rates them differently, but I can at least give you an idea.

For gutter screens, an aluminum wire gutter screen might cost about $4.25 per linear foot. While a powder coated wire trough screen could cost you around $5.50 per linear foot.

If you are looking for affordability, gutter guards are the right choice for you. On the other hand, gutter helmets (like LeafGuard) can get expensive.

LeafGuard and other types of gutter helmets could set you back about $30 per linear foot. Be aware that to buy gutter helmets you have to go through an actual franchise.

What you need to know about installing gutter guards

Regardless of what type of gutter guard you choose, it must be properly positioned under the roofing materials. If you have a drip edge (metal surrounds installed around the edges of the roof), gutter screens clamp to the front of the gutter, go under the entire roof and sit on top of the drip edge.

If you don’t have a drip edge, gutter screens will need to be installed between your shingles and your starting shingles. Otherwise the water will backflow, get under the materials and rot the bezel.

Gutter helms must be installed on your roof under the second shingle above the gutter line. If they are installed on your shingles, leaks will occur and you will need to replace the lower portion of your roofing around your home.

Will your gutters and gutter guards be removed during a roof replacement?

Now you know a little more about gutter guards, such as: B. the types, how much they cost and that they need to be placed in the right place on your roof. If you are in the market for a gutter helmet like LeafGuard, you will need to purchase the product and have it installed by a franchise location near you.

If you are interested in gutter screens, your local roofer can install them for you if they offer the service. But what happens to your gutters and gutter guards when you get a new roof?

Are they removed or replaced at the same time as your roof replacement? This is a problem for many homeowners, especially if they have invested in gutter guards.

Because it’s such a problem, we’re going to break it down for you.

The Bill Ragan Roofing team has been providing quality roofing and guttering jobs in the Nashville area since 1990. No matter what your roof needs, you can count on our craftsmanship to get the job done right. That’s why we’re proud to offer you a lifetime guarantee.

To learn what happens to your gutters and gutter guards during your roof replacement, read this article on Will your gutters be removed during your roof replacement.

Gutters are essential to channeling precipitation away from your foundation, so they deserve your attention year-round. In general, you should check your gutters at least twice a year (spring and fall are good times) to make sure they are free of debris and not leaking.

Thank God,

Fix leaky gutters

maybe not too daunting. You can always call a professional, or you may be able to do it yourself. Here are some of the most common causes of leaking gutters and how to fix them.

How to fix leaking gutter corners

If you see water seeping out of your gutter, you’re almost definitely dealing with it

common connection

between the gutter and the downspout is the culprit.

Clean the corner. Scrub with a wire brush, apply all-purpose cleaner, rinse with water and dry. Make sure the entire area is clean.

seal joints. Fill the area between the gutter and downspout with silicone caulking and pinch the joint joint as tightly as possible. Remove excess sealant and apply another bead around the edges.

Silicone sealant adheres best to dry, warm metal. That’s why it’s important to clean and dry the gutters before applying the grout, and to carry out the repair on a warm day if possible.

How to repair holes in a gutter

All gutter materials can be subject to the occasional puncture, whether it’s from rust or a puncture wound, but the good news is that this is another fairly easy fix.

Clean the area around the hole using the same methods we discussed above. Make sure you completely dry the area before the next step.

Apply roofing cement around the hole and then patch it with metal sheets.

Cover the fillet completely with more roofing putty.

Roof cement, like joint compound, works best on warm, dry metal.

Reseal gutter joints

If you have a seam leak, you can most likely see the evidence, whether it’s water coming down from the seam or a particularly wet spot on the floor below. If it’s not quite as obvious, look for debris in the gutter. If a pile of leaves gathers near a certain seam, you’ve probably found the leak.

Separate the seam. As a rule, joints and screws are removed for this purpose. After that, the gutter pieces should come off easily. If it doesn’t, you may have missed a screw.

Clean the seam using the same methods discussed earlier. Remove all grout, dirt and other debris. You may want to repaint the area with a rust resistant spray paint. If you do this, make sure the paint dries completely before proceeding.

Apply sealant to the inner lip of the downhill and press the riser onto it, holding together long enough to properly distribute the sealant. When you’re sure it’s tight again, replace all the screws to complete the task.

Issues requiring replacement

While the above issues can be fixed fairly easily, there are some issues that might require you to consider new gutters. If your gutters tend to loosen or seem to be coming loose from the roof, or if your fasteners are falling off faster than you can replace them, you need to get it evaluated right away. If you notice water in your basement, it could also be a sign of a serious problem with your gutters.

If you notice any of this happening, give us a call and we’ll be happy to help you diagnose what might be going on.

Gutters are an important part of the overall health of your home. Checking them twice a year and fixing small problems before they become big problems will save you a lot of money and a lot of headaches.

Are you looking for accessories to increase the protection of your gutter system? Rain deflectors and water butt deflectors are popular options, but some homeowners confuse the two.

Advantage Seamless, your state’s premier seamless gutter company, explains the difference between the two below.

Rain Deflector: Aesthetic Necessity

Rain deflectors are unobtrusive metal strips placed primarily for aesthetic reasons. Some homeowners find gutters visually unattractive and so install rain diverters to divert rainwater towards the gutters.

However, rain deflectors can also serve a more functional purpose. They can be installed in homes without a porch to keep you dry while trying to open your door or leave the house. Gutter installers also install rain deflectors on parts of the roof where gutters cannot be installed. Just remember that they are not a substitute for gutters; They are more of a replacement for your gutters on the more visible or inaccessible parts of your roof.

Rain butt deflector: Additional drainage protection

Meanwhile, water butt diverters or downspout diverters are usually installed for a more functional purpose. Rain barrels are used to collect excess rainwater for future use; To ensure that the rainwater stored in the barrels does not spill onto the pavement, rain butt deflectors are used. Once the keg is filled, the excess water flow is diverted through a hose and back to the downspout. The rainwater overflow can be routed to a second barrel if there are additional connections on the diverter.

While gutter accessories can never replace gutters, they can still play an important role in preventing moisture damage in your home. For this reason, you should only hire a reputable contractor to install and maintain your gutters.

Advantage Seamless is a family business providing gutter cleaning and installation services. To schedule a free appointment, call us at 218-270-5454 or fill out this form. We serve homeowners in Baxter, MN.

When it comes to roof fitting and protection, drip edge and gutter skirt are both terms you should know. However, we understand that not everyone is a professional local roofer and that words like drip edge, metal surround and gutter skirting may not be in your normal vocabulary. Good luck to you, that’s what we’re here for! In this post, our team of roofing specialists at Quality Exteriors will break down the drip edge vs gutter skirt and the difference between the two.

Whether you have storm damage or are simply interested in improving your home, we have a team of dedicated home builders ready to meet your specific needs. QEI specializes in providing roofing, siding and window services for the Shreveport-Bossier City areas. We also offer free appraisals and inspections of your home or business according to your needs. With Quality Exteriors you are guaranteed to receive the highest quality of service and workmanship.

What is drip edge?

There are many different things that can contribute to water entering your home and causing damage. One of the most common causes is a lack of proper protection along the roof shingles where your roof edge meets your home. This is where a so-called “drip edge” comes into play. The drip edge is a type of metal shroud that prevents moisture from entering at this vulnerable point. Its purpose is to direct water away from interior areas where it shouldn’t be, helping to protect your existing roof from damage and possible rotting from water ingress.

Drip edges are an important part of the home but are not always installed during the initial construction of a home. Some states require the drip edge to be installed, while others highly recommend it.

A roof drip edge is a T-shaped piece of metal that is installed along the perimeter of a home’s roof and essentially forms a watertight seal around the edge of the roof. The front of the metal drip edge must overlap the gutter to prevent water from falling into the gaps. Its purpose is to filter water out of the roof by directing it away from the face and into the gutter. This will prevent rotting of the bulkhead holding the gutters and prevent them from falling onto your roof system.

Drip edges can be virtually any color, but the most common colors are neutral colors like white, black, and brown. It is also possible to color match your roof shingles or gutters to the drip edge for a more distinctive look. Some people may even choose to use an accent color for their metal drip edge to “pop” the roof or to complement other parts of the home like shutters or doors.

The strip of sheet metal that runs under the roof along the eaves of your home is called the eaves strip or eaves edge. Eaves moldings help support the roofing that extends beyond the roofing and prevent rainwater from running down the face.

On many homes, the eaves strip is made of galvanized metal, which does not hold paint well and can rust over time. A better alternative is vinyl-coated aluminum eaves, which will not rust and do not require painting.

The drip edge is often replaced when new shingles are installed, but can be replaced at any time. Asphalt roofing shingles can become brittle in cold weather, so wait until a warm (but not hot) day to remove and replace the eaves stripping.

Tools and materials needed:

director

Flat crowbar

hammer

tin snips

strip the eaves

Galvanized roof nails

Remove eaves:

Carefully lift the shingles along the bottom edge of the roof and locate the nails that attach the eavestrip to the roofing. Use a flat pry bar and a hammer to remove the nails holding the eaves strip to the roofing. Pull the eaves strip out from under the shingles.

Replace eaves:

Install the eaves along the lower edges of the roof first, with the eaves under the shingles and felt backing. Align one end of the bottom eaves strip flush with the edge of the roofing material. Lift the shingles and nail down the eaves strip with galvanized roofing nails. Overlap the other pieces of eaves strip by at least 1 inch and nail in place. Cut the last piece at the bottom eave flush with the roofing at the other end. Install the Gable Eaves Strips over the Felt Pad and onto the Lower Eaves Strips. Cut and bend the end of the eaves strip to cover the gap between it and the bottom eaves strip. Overlap the taller gable ledges with the lower ones by at least 1 inch. At the ridge, a gable eaves band runs parallel to the peak of the roof. Cut and bend the top end of the matching Gable Eaves Tape so that it extends at least 1″ past the roof peak and overlaps the matching Gable Eaves Tape. Miter the end of the eaves strip of the pediment so that it is plumb.

Watch this video to learn more.

Further information

VIDEO TRANSCRIPT

Danny Lipford: Everyone knows how important your roof is in protecting your home from the elements, but you may not realize how important that little strip of metal is to your overall roofing system. It is called eaves strip or eaves plate.

Now many houses have galvanized metal eaves to protect it from rusting. But without the proper maintenance, it can become very unsightly with all the rust stains that can form.

Now an alternative is to replace it with this type of metal which is a vinyl coated aluminum that will not rust. And it doesn’t need any kind of painting, just a little cleaning from time to time. Now it’s generally replaced at the same time as your shingles, but it’s really quite easy to replace at any time.

The shingles along the bottom edge of the roof are carefully lifted to avoid damaging them and then a flat pry bar is used to remove the nails holding the eaves strip to the deck. The new stripping is pushed over the roofing felt but under the shingles. Finally, the tricky part is nailing down the new strip while holding the clapboards up.

Replacing the eaves on a home is quite labor intensive, but nowhere near as much work as sanding, priming, and painting rusty metal.

Print/Save as PDF

Your roof is a combination of different components and roofing materials that come together to protect your home and family from the elements. But most homeowners are unaware of these materials or why they are important to your roof.

One of the materials that your roof absolutely needs is the drip edge. Since every roof needs it, we’re going to break down this crucial roof component.

Here at the Bill Ragan Roofing Company, we want you and every homeowner in the new roof market to understand the investment you are about to make. That’s why we’re giving you the information you need to understand what affects price so you can make the right buying decisions.

By the end of this article, you’ll know what a drip edge is, why your roof needs it, and more. And don’t forget to stay tuned to the end to continue reading about the other important roofing materials you need to know.

What is drip edge?

The first thing to know about the drip edge is what it actually is and where it is located on your roof.

The drip edge is a sheet of metal that is installed around the edges of the roof to keep water off your roofing and under your roof components. If your roof doesn’t have a drip edge, water will seep behind your gutters and rot both your headboard and roofing.

With a roof replacement, your drip edge will need to be replaced. Be aware that some roofers will shy away from your estimate to lower their prices to beat the competition.

To avoid this happening to you, it’s important not to shop around for the cheapest roof replacement you can find.

The building code requires a drip edge

Building codes ensure that your home and roof meet your state’s requirements to pass a home inspection. One of the most important codes has to do with drip edge.

According to IRC 2018 Code R905.2.8.5: A drip edge shall be provided at the eaves and gables of shingle roofs. This code means that the drip edge needs to be installed around the edges of your roof.

Not only does it need to be installed on your roof to comply with this code, it also needs to be installed correctly.

The remainder of code R905.2.8.5 states: Adjacent portions of drip edge must overlap at least 2 inches. The drip edge must reach at least 1/4 inch below the roof covering and at least 2 inches up. The underlay must be laid over the drip edge along the eaves and under the underlay at gables.

Keep in mind that some roofers cut corners by omitting the drip edge or being too lazy to install it properly. In this case, it becomes much more difficult to pass a home inspection because your roof is not compliant.

The circumstances when no drip edge is required

You have just learned that the drip edge needs to be installed on your roof in order to comply with the regulations. However, there are circumstances where a drip edge is not “technically” required.

If you have a pre-bent aluminum fascia that sits flush with your roofing, this will serve as a drip edge. There are also rake shapes that serve as a drip edge on homes built before the industry began using aluminum siding.

Just like a regular drip edge, aluminum screens and rake bars run along the eaves and cover the edge of your roof surface to prevent water from getting where it’s not supposed to. If your home has one of these, you don’t need a drip edge.

The cost of drip edge

The drip edge will always be included with your roof replacement. Because of this, it affects the price you pay for your new roof.

The standard drip edge used (aluminum) costs approximately $2.00 per linear foot, including labor for installation. If you switch to another metal (steel or copper), it will cost even more.

However, keep in mind that the roofer you hire has a big impact on the price you pay to install the drip edge and the rest of the roofing material. While roofing materials should cost the same everywhere, every roofing company has different overhead and labor costs.

So even if one charges $2.00 per linear foot, another may charge $3.00 or more because their labor costs are higher. Note that this price is based on a roof replacement only.

If you need to retrofit your current roof or add a drip edge, the labor cost is much higher.

Learn the rest of the important roofing materials

Now you know what a drip edge on your roof is, why you need it and much more. Remember that the drip edge is not only a crucial roofing component, but also a code that home inspectors look for.

To avoid being taken advantage of or failing a home inspection, hiring a great roofer who doesn’t cut corners is crucial. After reading this you will be a little better informed about the materials that make up your roof.

However, there are more materials that you and any homeowner need to know about before approaching a roofer. Because we want you to have the knowledge needed to make the right decisions, we’ve written another article that breaks down the 9 essential roofing materials to be part of your roof replacement.

The Bill Ragan Roofing team has helped Nashville homeowners understand what exactly they are paying for when they get a new roof. We go through all the roofing materials and your options to ensure you get a roofing system that fits your budget and will last for decades. Even if you don’t work for us, at least you have the power to make the right purchasing decisions.

Check out 9 Materials to Make Your Roof Replacement to learn the important roofing materials that make up your roof.

Does the roof of your house have a drip edge? If not, it probably should.

Drip edges are among the best ways to control moisture during building design, construction, and maintenance, according to a report released by the EPA. But what is the purpose of a drip edge and why do you need one on your roof? Without a drip edge, this excess water can damage your roof, sidewall, porch, and even your basement. Learn more about what a drip edge can do for your home or structure below.

What is drip edge?

A drip edge is an angled sheet of metal that is fitted over a bulkhead. The purpose of a drip edge is to divert water from the fascia into the gutters. The gutters then drain this water away.

Drip edges can be mounted on sloping roofs, eaves and gables. They extend beyond the attic and are at least a third of the width of the channel.

Metal drip edges are typically made from a non-porous, non-corrosive metal such as galvanized steel, aluminum, or copper. They can also be made from durable plastic, vinyl, or fiberglass.

Why do I need a drip edge on my roof?

Any homeowner interested in protecting their home and extending the life of their roof should consider installing drip edges. Benefits of installing a drip edge:

They prevent damage to eaves and soffits: Drip edges direct water away from the sensitive soffits and eaves areas of your roof and channel it into your gutters. If your reveal and fascia are exposed, they can be damaged by the excess moisture. This damage can take the form of discoloration and wood rot.

Drip edges direct water away from the vulnerable soffit and eaves areas of your roof and direct it into your gutters. If your reveal and fascia are exposed, they can be damaged by the excess moisture. This damage can take the form of discoloration and wood rot. Drip edges keep bugs out of your home: Drip edges cover the “carpenter’s gap” in your roof. A carpenter’s gap is the area between a roof deck and a fascia board. This area of ​​your roof is often responsible for allowing small animals or other unwanted pests into your home through your attic.

Drip edges cover the “carpenter’s gap” in your roof. A carpenter’s gap is the area between a roof deck and a fascia board. This area of ​​your roof is often responsible for allowing small animals or other unwanted pests into your home through your attic. YOU CAN KEEP YOUR PORCH DRY: Because drip edges divert water down gutters, you don’t have to worry about a downpour washing off your roof and onto your porch or patio during heavy rains.

Because drip edges divert water into gutters, you don’t have to worry about a downpour washing off your roof and onto your porch or patio during heavy rain. They stabilize your roof: Roof edging sheets can help stabilize your roof in strong winds or rain. Since wind damage is one of the top reasons homeowners make an insurance claim, it’s a benefit you shouldn’t ignore.

A roof flashing can help stabilize your roof in strong winds or rain. Since wind damage is one of the top reasons homeowners make an insurance claim, it’s a benefit you shouldn’t ignore. Drip Edges Protect Your Roof From Ice Dams: Winter can be a dangerous time for your roof. Ice dams are accumulations of ice that accumulate and freeze at the edge of a roof. Ice dams prevent snow from thawing and draining properly. If the snow isn’t able to thaw and drain, this moisture will back up and become trapped on your roof, adding weight and potentially causing wood rot. If this moisture finds its way into your home, it can lead to mold or mildew growth. The drip edge connection prevents the formation of ice dams.

Winter can be a dangerous time for your roof. Ice dams are accumulations of ice that accumulate and freeze at the edge of a roof. Ice dams prevent snow from thawing and draining properly. If the snow isn’t able to thaw and drain, this moisture will back up and become trapped on your roof, adding weight and potentially causing wood rot. If this moisture finds its way into your home, it can lead to mold or mildew growth. The drip edge connection prevents the formation of ice dams. They Protect Your Basement: When drip edges divert water away from your roof, they also divert it away from the part of the floor just below your roof, which often leads to your basement. Without an intervening drip edge, heavy rain can allow water to seep through the floor into your basement.

understand drip edges

While the importance of drip edges is undeniable, many homeowners have questions about installing drip edges.

Can a drip edge be installed on an existing roof?

Although the ideal time to install gutter drip edges is during the initial construction of your home or roof, it is possible to install them on existing roofs. In fact, building codes in many places in the United States require structures to have drip edges because they are so beneficial. For the same reason, many homeowners choose to install drip edging on their existing roof.

Are different types of drip edges available?

Numerous styles and types of drip edges are available. When choosing drip edging for your home, you should make sure you choose a material and color that matches or complements the style of your home. A cohesive exterior will increase the appeal of your home.

Three common types of drip edges are:

C-style drip edge: C-style drip edges are curved like the letter and help drain water off the roof deck. They are placed under the roofing material and shaped to underlie the decking. C-shaped edges are typically applied to roofs that do not have fascia boards.

C-style drip edges are curved like the letter and help drain water off the roof deck. They are placed under the roofing material and shaped to underlie the decking. C-shaped edges are typically applied to roofs that do not have fascia boards. L-Shaped Drip Edge: L-shaped drip edges are bent in the middle, forming a 90-degree angle. One end of the “L” is under the roofing material and the other rests on top of the fascia, holding it securely. L-shape drip edges are typically used on low pitched roofs.

L-shaped drip edges are bent in the middle, forming a 90-degree angle. One end of the “L” is under the roofing material and the other rests on top of the fascia, holding it securely. L-shape drip edges are typically used on low pitched roofs. T-Shaped Drip Edge: Although more complex than C- and L-shaped roof sheets, T-shaped roof drip edges are very efficient at keeping water off a roof. T-style drip edges use an extra piece to form a triangular shape between the roof terrace and the house.

Who should install a drip edge?

When it comes to drip edge installation, it’s best left to experienced professionals. If a drip edge is installed incorrectly, water will not flow down the gutters properly. This problem can lead to wood rot and other water damage that can destroy the parapet and soffit. Damage caused by an incorrectly fitted drip edge can result in costly repairs in the future.

The drip edge should be angled to allow rainwater to drip directly into the gutter. However, each roof is unique and may require the drip edge to be bent or installed in a way that allows this action to take place. If you notice water dripping between your home and the gutter, it can be as simple as readjusting the drip edge.

Consult a professional for the proper installation of the drip edge

All Season Gutters is a local family business in Central PA specializing in gutter and roof installation maintenance, fascia and soffit replacements, and gutter guard installation. We combine 15 years of experience with high quality materials and reliable service and offer them to you at a competitive price. At All Season Gutters, we are passionate about helping homeowners keep their homes safe for years to come. Read our references to learn more about the quality of our work.

Are you interested in drip edge mounting? Arrange a free estimate today!