How To Fix A Burnt Novo Pod? The 80 Top Answers

How to clean a burnt coil

Desserts, fruits, sweets, drinks, ice cream, menthol, tobacco – with so many different flavor profiles to choose from, finding the right one can be difficult and time consuming. And when you’ve found your perfect taste, the last thing you want is to spoil your hit with the foul taste of a burnt coil.

If your usual vapor is tainted by the acrid taste of smoke, chances are the wicking material in your coil has been singed. Often made of cotton, the wick draws your e-liquids to the heating element where your liquid is vaporized. If there is not enough liquid left to vaporize the coil, your coil will continue to operate without the required liquids. This causes the wick to burn dry, causing a pungent burning taste that spoils the flavors of your e-juice.

HOW DO I KNOW IF MY COIL IS BURNED?

Due to the sharp, unpleasant taste of a burned coil, there is no doubt that your coil is burned. You may also notice some visible signs that your coil is burned.

What does a burnt coil look like?

At first glance, a burnt coil doesn’t necessarily look any different than a normal coil. However, the inner wick shows obvious signs of damage with singed and burnt edges.

Can you fix a burned coil?

While burnt coils are best replaced as soon as possible, the good news is that you can give them a little extra life while you wait for your new coils to arrive.

STEP ONE: WATE YOUR REELS

First, remove your coils from your vape and soak them in a bowl of hot water to loosen any residue.

STEP TWO: CLEAN YOUR COILS (optional)

If the residue doesn’t come off when you soak, try adding a little lemon juice or vinegar to your bowl of hot water. Then soak in hot water to remove any traces of lemon or vinegar that could alter the flavor of your vape juice.

STEP THREE: AIR DRY

Remove your coils from the water tray and place them on a flat surface or towel where the coils can air dry.

STEP FOUR: PREPARE BOBBINS

Priming your coils is the best way to avoid dry hitting. By soaking your coils with a small amount of your e-liquid, your wick will soak up the liquid to prevent burning.

STEP FIVE: REPLACE

Finally, put the coils back into your vape and vape as usual.

THE FINAL JUDGMENT

Cleaning your coils is a great way to give your coils an extra life if you can’t replace them with new ones right away. However, this is not a hard and fast rule as in some cases your coils are beyond repair. It’s best to keep a spare coil handy for emergencies to ensure you don’t get caught without your vape.

And don’t forget, the best way to avoid the unpleasant taste is to make sure you prep your coils and always have enough liquid in your tank.

If your vape kit has a burnt taste, it usually means one of three things:

1. Your pod/tank/cartridge is out of e-liquid

2. You may be using an inappropriate e-liquid or power setting

3. Your pod/tank/cartridge may be defective

My tank/clearomizer is bursting

This is sometimes the case right after filling your clearomizer or tank. You can easily burn the moisture-wicking cotton material when it’s dry, and unfortunately, once it’s burned, there’s little you can do to revive it. To avoid this, always leave the clearomizer/tank for 5 minutes after filling or rinse the e-liquid around the clearomizer/tank to ensure it is absorbed by the wick before use.

Another way to do this is to prime the clearomizer/tank by taking a few puffs without holding the battery button. The suction created forces the e-liquid into the wick area of ​​the coil, allowing the wick to become saturated with e-liquid. Take about five puffs without activating the battery, but don’t exceed that amount. If you take more than five puffs, you can flood your coil and risk sucking e-liquid into your mouth.

With larger coils (e.g. sub-ohm coils) it is always best to drip a few drops of e-liquid directly onto the cotton wool inside and outside of the coil head. Be careful not to flood the coil head or it will not vaporize the e-liquid properly.

Always make sure you use an appropriate e-liquid. Low resistance coils (less than 1.0 ohm) work best with high VG e-liquids. High resistance coils (above 1.0 ohm) tend to work better with higher PG e-liquids. Any e-liquid with a 50/50 formula should work well in most vape kits.

If your device has an adjustable power output, setting it too high can cause your coil to burn out faster than normal. It’s best to start with a more conservative output and then slowly work your way up from there. If you start experiencing dry hits, it may indicate that your setting is too high.

My pre-filled pod tastes burnt

If you’re using a pre-filled capsule (such as a Myblu, JUUL, Vype, or Mini Gusto capsule), your capsule may start to taste burnt when it’s empty. If this is the case, you should simply replace it with a new one.

If your pod tastes burnt but still contains plenty of e-liquid, this indicates an error. You should submit a ticket to our helpdesk with more details.

Certain pre-filled capsules require preparation prior to first use. If you are using an IVG, Mini Gusto or Yearn pod, you will need to click the pod into the device and wait 5-10 minutes. This is because the coil and e-liquid chamber are kept separate until activated.

My refillable pod tastes burnt

Many devices use pods that are refillable. Usually, you cannot change the coil on these types of pods, except for certain SMOK products.

You should always prepare a new Pod before using it for the first time. To do this, simply let the pod rest for up to 10 minutes after the first filling. Unfortunately, if you haven’t prepared your new pod, there is no remedy if the internal coil has burned out, requiring you to install a new pod.

It’s also important to make sure you’re using an appropriate type of e-liquid. Many pod systems are mouth-to-lung, meaning they don’t produce much vapor. For this reason, we recommend using e-liquid with no more than 70% VG; 50/50 mixes usually work best!

Is your vape burning your throat?

It’s happened to all of us: we grab our vape, take a long hit, and instead of a great-tasting, soothing vapor, we get an unpleasant burning taste and a horrible throat sensation. Burnt hits are one of the worst things a vaper can experience. And it can happen with just about any vape, from disposable vapes to cloud-eating sub-ohm tanks! It can ruin your day and, worse yet, keep you from vaping. While there are many reasons for an arson attack, the good news is that most can be avoided. Let’s examine some of the most common causes of burns and what you can do to prevent them.

Burnt hits vs. dry hits

Although most vapers use these terms interchangeably, they are actually two different things. Dry punches, while not pleasant, are far less shocking than burnt punches. A dry hit will become apparent once your coil’s wick is slightly dry. You get less flavor and exhale less vapor without the nausea and coughing that comes with a burnt hit. But keep vaping on those dry coils and you’re in for a surprise… Think of a dry hit as a red flag to watch out for: don’t ignore that dry, tasteless vape you’ve taken! The burnt hit is coming soon. But why is it happening?

What Causes a Burnt Hit?

Burnt hits are the result of powering an atomizer when there is no liquid or not enough liquid on the wicks. With no liquid to vaporize, the coils begin to burn the wick and the user essentially inhales burnt cotton. Here are some of the most common reasons for burnt hits and some advice on how to avoid them. High wattage

Vaping at wattages that exceed coil ratings will cause e-liquid to vaporize too quickly. When this happens, the coils can burn the wicks even if there is some juice left. Always stay within the recommended wattage ranges. chain vaping

The wick dries out quickly with many puffs in a row. When you feel a burnt hit coming by noticing a slightly toasty flavor, put your vape down for a moment. This allows the liquid to cover the dry areas of the wick. Vaping with high VG e-liquids

Not all vapes are created equal. Some vape tanks allow high VG juice, while others often require 50% PG or more to function properly. A good rule of thumb is to check the size of the wick channels. If the holes are small in diameter, chances are your tank of high VG juice is boding ill. Incorrect suction of bobbins

This is probably the most common problem on the list. Priming your atomizer heads is essentially the process of preparing them for first use by saturating the wicks with e-liquid. If you want to avoid a burnt hit, remember to always prime your coils properly.

Prepare your coils: stop the burned hits

While the idea is always the same, the process of preparing your coils will vary depending on the equipment used. Here’s a look at how to prime some of the most commonly used vapes.

How to prepare vaporizer coils

All vape tanks that come with interchangeable coil heads share more or less the same structure and require the same simple steps to get set up. You must repeat this process each time you replace a spool. Take a new spool out of the packaging

Drip some e-liquid onto the wick holes and into the coil head (3-4 drops are enough).

Assemble your tank and fill it with E-Juice

Screw your tank onto your mod and set aside for 10 minutes

Inhaling at the top of the tank without firing will speed up the process

For wattage adjustable vape mods, start with the lowest recommended wattage and gradually increase until you find your sweet spot. Note that you may get some spit back on the first few hits due to the extra liquid that may have accumulated inside the coil. If it doesn’t go away and you’re using a variable wattage mod, try bumping the wattage up a bit for a few hits – but make sure you don’t exceed the coil’s top wattage as that will most likely burn it.

How to prepare refillable pods

Refillable pod systems usually come with no e-liquid inside the pod. The process is even easier with this type of vape as you cannot remove the coil from inside the pod. Fill the pod with e-liquid.

Let it saturate for 10 minutes. Take a few breaths on the pod itself, not the battery (just in case it activates by pulling). This forces some liquid into the wick channels and gives you extra security against dry hits. If this is your first time vaping with a pod, try taking shorter hits at first. Some of the smaller coils need to be broken in a bit before sliding. If you take really long hits in the beginning, even if the wick is fully saturated, you could end up with a burnt hit. Think of it as slowly increasing the wattage of an adjustable power mod. That’s it. You can start vaping now!

How to tell if your coil is burned

After a nasty incendiary hit, your coil is probably ready to be discarded. If you made it early, you can still give it a try and see if the burnt taste goes away after a few hits. Unfortunately, chances are you’ve already burned some of the cotton in the spool and it needs to be replaced. That taste won’t go away unless it’s really burnt! Burnt draws aside, if you’ve primed your coil properly and made sure it’s adequately supplied with e-liquid, you might be wondering why you keep getting a burnt taste out of your vape. While burns are the most common cause of neck burns, they are not the only ones. A coil can be burnt for a number of reasons and while the sensation isn’t as pronounced, you’re certainly not getting the most out of your e-liquid. Knowing when your spiral is ready isn’t a science, it’s a learning process. The more you use a vape tank, the more conscious you become of the time it takes to take a new coil out of the box. The first sign is usually a loss of flavor followed by a drop in vapor production. Even at this point you can squeeze a little life out of your coil. But if you’re out of supplies, now’s a good time to get some.

How often do you have to change coils?

Coils break. Unfortunately, they don’t have an expiry date: the lifespan of your atomizer head depends on a variety of factors. Even if you’ve never had a dry hit, a coil will eventually “burn” and taste bad after extensive use. There are a number of parameters that you need to consider when attempting to estimate the expected lifespan of your coils. consumption

A coil is generally good for up to a certain amount of e-juice. The more you use it, the faster it dies. Coil life is sometimes calculated in days or weeks, but the most accurate way to calculate it is in ml – some people only vape a few ml per day while others use 10-20ml or more. E-Liquid Ingredients

If you want your coils to last, try to avoid sweeter juices – especially those that come in high VG ratios. Sweeteners are notorious for clogging coils and reducing their lifespan, and VG’s thickness only makes matters worse. wattages

Vaping at the higher end of the recommended wattage will stress your coils and shorten their lifespan. In fact, your coil will “tire” and start flirting with burnt punches. Vaping at the lower recommended wattages is also not ideal as it could shorten the life of your coils due to residual build up – e-liquid that is not vaped can caramelize your coils over time. Try to stay somewhere in the middle for best results. While there is no universal rule, most properly primed coil heads will generally last anywhere from five days to two weeks. Coils in mouth-to-lung tanks tend to last a little longer than sub-ohm coils due to the lower amount of e-liquid that flows through the coils in a day – although there are many exceptions to this “rule”. . If you use your tank regularly and haven’t noticed a drop in flavor after a week or so, you might want to consider proactively changing your coil. Flavor and vapor production can decrease very gradually and go unnoticed. In the meantime, you’ll be vaping with some underperforming coils – get a new coil in your tank and you’ll be amazed at how much better it tastes.

Does your new coil taste burnt?

If you prepared your new coil properly but have a burnt taste — or an odd taste — replace it. Chances are you have a dud. Not all coils are the same, especially when you consider the number of pieces that are produced each day. Some coils are inherently bad, possibly due to a manufacturing error that caused a poor fit or loose connection. Luckily, it’s rare nowadays to find large “bad batches” of coils on the market. That said, if you ever get a bad spool that doesn’t perform like the previous ones, chances are you’ll get more bad spools from this pack. To protect yourself from running out of good coils, consider buying more than one pack of coils when you restock. If you can, consider buying the same coils from another store as the batch is more likely to be different.

Hit the burnt hit!

Now you understand the different causes of burns, how to prevent them and how to stop them for good! If a sneaky arson attack happens, at least you know the likely causes and what to do about it. Do not be discouraged. Vaping is a convenient and safer alternative to smoking. If your current coil tastes burnt, get a new one and discard the bad one. Just don’t forget to prime it first!

Our top tips for avoiding vapor tongue

Vaper’s tongue affects a lot of people, but how much do you know about it?

December 14, 2021 | Hannah Ruby

Vaper’s Tongue – What you need to know

Vaper tongue is a well-known problem that affects many vapers, especially those who are new to vaping and are unaware of the problem. The problem means that vapers often experience taste differences, what was once a favorite vape suddenly tastes terrible, a numb tongue or even a loss of taste.

If this affects you, don’t worry, it’s not serious or permanent. Vaper tongue (also known as vape fatigue) is a term that covers taste-related discomfort. Often this is done through the frequent use of a single, individual flavor. So if you’ve been vaping the same flavor for a few weeks. You’ll probably start to notice the difference in taste, or lack thereof. It usually goes away on its own in a couple of weeks without help.

Let’s look at what can cause vapor tongue and what you can do to avoid it.

The causes of the steam tongue?

1. Vaping one flavor for too long – after using the same flavor for a long time, the taste will start to change or you will lose your sense of taste due to fatigue of your taste buds.

2. Damaged taste buds – one of the simplest causes, taste buds that have been damaged from smoking, infections, alcohol, extremely acidic foods, spicy foods and some medications can also lead to vape tongue.

3. Dehydration – Perhaps surprising, but dehydration is another possible cause.

4. Dry mouth – Unfortunately, a lack of saliva can lead to a loss of taste. Staying hydrated can help combat this.

5. Stuffy nose – you wouldn’t believe it, but we understand flavors through our sense of smell. With a stuffy nose, you’ll find that the flavors are much more subdued, if at all, especially when dealing with a complex flavor.

6. Illnesses & Medications – Illnesses like cold and flu are obviously linked to the vaper tongue as it can often cause you to lose your sense of taste. It is also wise to note that head injuries and vitamin deficiencies can also be a cause. If you experience repeated or prolonged periods of taste loss, it may be best to speak to your GP to have everything checked out. Similarly, a number of medications can cause taste loss. Be sure to check your side effects as it could be these rather than your vape that are causing you to lose your sense of taste.

7. E-Liquid Obsolete – E-Liquids have a shelf life. You will usually notice this by a change in color or taste. If your vape is starting to taste weird, especially if you haven’t vaped it in a while, that could very well be the cause. Check the expiry date on the bottle and make sure you are storing your e-liquid properly.

how to avoid it

1. Change the taste – the simplest solution; Change your vape juice from time to time. By simply changing the flavor you’re vaping and coming back to it after a few weeks, you can help ward off the vaper’s tongue and keep the flavor fresh.

2. Use a stronger flavor – rebalance your taste buds with strong flavors like menthol or mint. When your vape flavor fades, puff on these strong flavors for a while to bring it back.

3. Drink water – stay hydrated. It also clears the palette and can help with dry mouth.

4. The smell of fresh coffee beans – this is a technique used by professional wine tasters and used by many of our own vapers. By inhaling the scent of fresh coffee beans, it can help reset your sense of taste (a weird one we know, but somehow it works).

5. Suck on a lemon — like coffee beans, this citrus blast is said to help reset your taste buds. If sucking on a lemon isn’t your forte, try a lemon dessert or even a lemon-flavored vape.

6. Mouthwash – back to those strong flavors, mouthwash could be a great way to break free from the vaper’s tongue. But be careful as these can be quite strong flavors that could accidentally cause the vaper to tongue.

7. Using steeped e-liquids – Using steeped e-liquids, which offer more refined flavors, means you get more flavor into your vape. Steeped e-liquids can offer a smoother, more refined flavor that’s less likely to trigger the vaper’s tongue, but you may lose some of the throat hit of steeped liquids. Steep e-liquid is vape juice that has been blended over time rather than simply shaking to mix your liquid and then vaping. There are several ways to infuse your e-liquid including these useful ways.

ADVERTISEMENT

By: George Kassimis

Of all the reasons vape coils burn out, chain vaping is probably number one. Chain vaping is when a user takes multiple puffs within a short time frame (usually around 5-10 seconds between each puff), preventing the wick from soaking up enough e-juice before the next puff, causing the wick to burn. This isn’t a huge problem with rebuildable coils as in this case you just need to retract the coil and you’re good to go. However, you are out of luck with disposable spools as the burnout will now permanently damage your spool. To be clear, it’s not frequency but the lack of time between puffs that prevents the wick from reabsorbing the juice.

If you are a regular user and allow time (about 20 seconds) between each draw, this shouldn’t be a problem for you.

However, if you find yourself chain vaping all the time, it’s probably best to be a little more aware of when your coil needs a rest. To prevent further burn-outs and extend the life of your coil, it’s best if you just stop vaping for a while. If your flavor seems faded, it could be a sign that there isn’t much liquid in your coil and you’re about to burn the wick. Much like preparing your coil when you first bought it, your wick will need time to reabsorb the liquid and “re-prime” itself. To do this, simply set your vape aside for around five to 10 minutes and you should be fine.

RDTAs (Rebuildable Dripping Tank Atomizers) are probably the best when it comes to chain vaping. These coils are more adjustable and can be tuned to match a chain steamer. Personally, I thought the Griffin RTA (Rebuildable Tank Atomizer) was great, but most rebuildables should do. If you are building your coil for chain vaping, packing about 2mm of wicking material should be sufficient. It’s usually best to pack the atomizer until the material is evenly seated on the wick hole (not too loose or tight). When choosing your moisture-wicking material, rayon is personally recommended over cotton. Viscose has a higher fire point (higher temperature tolerance before burning out), absorbs juice faster, is cleaner, and lasts much longer. It’s just as popular today as cotton, and it’s cheaper. Using a temperature controller is also recommended as it will prevent your coil from getting too hot. While it may seem difficult at first, mastering the build will eventually result in your perfect vape and make you appear like a crafting wizard.

Chain vaping and direct dripping shouldn’t pose much of a problem. Unlike tanks, dripping requires you to constantly moisten the wick as there is no tank to draw juice from. A few drops each time should give you about four to six hits. If you see yourself vaping chains, just make sure to add more drops every four draws, just to be safe. This way your wick stays soaked and doesn’t burn out.

Although chain vaping is fairly common as most vapers are ex-smokers, it should be clear that it will shorten the lifespan of your coil. While some coils are stronger than others, it really depends on how often and for how long you draw. If you find yourself chain vaping, it’s probably best to stick to RDTAs and direct drip. This is due to the power as well as the direct control that these methods allow. But if you only have a sub-ohm tank at the moment, try the techniques above. They should prevent your coil from burning out so quickly and you unnecessarily spending a lot of money on new atomizers.

manufacturing quality

While the honeycomb/cobra pattern has been a trend slowly penetrating most Smok mods lately, the Smok Novo is the first pod-style device to utilize the design, making it quite unique in its size category. Shaped like a fancy whistle, the overall profile of the Smok Novo features no sharp or jagged edges, instead making straight lines and smooth edges to create an ergonomic form factor that’s easy on the hands. Utilizing an integrated 450mAh battery, the Smok Novo holds quite an advantage over the older and smaller Smok Infinix in terms of battery, while slightly sacrificing a marginal amount of portability. The Smok Novo consists of only two components, namely the main body, which contains the battery, and the pod itself, which is a coil, tank, and mouthpiece combination. It feels solid enough and doesn’t produce any audible noises or rattles when handled. Users who are interested in oil cartridges with a 510 thread often prefer the PCKT One Plus. The lack of a display is compensated by a smart singular LED display, which is quite diverse in its functionality. Not only does it flash appropriately to let you know how much charge the battery has left, but the indicator also includes specific prompts about the status of the Smok Novo, such as: B. if the device is switched on or off or if there is a potential problem with the coil being defective and shorted out. The convenient location of the micro USB charging port also makes charging the Smok Novo easier, not to mention the non-proprietary cables that allow the user to easily find a replacement cable in case the included cable is lost or misplaced.

taste quality

Despite its small size, the Smok Novo hits surprisingly hard, trumping its smaller brother the Smok Infinix when it comes to overall vapor performance. This significantly increases the aroma release. Another strength of this device’s pod system is the sheer durability and longevity of the pods. Each pod lasted at least a week in our experience, with some even hitting the 2 week mark before there was a noticeable drop in flavor and vapor performance. One caveat, however, is that some pods tend to leak, so you may need to watch out for that when choosing the Smok Novo. People who use 510 cartridges usually prefer the Yocan Uni Pro.

performance flexibility

As a pod-style device, the Smok Novo by default lacks many of the advanced features found in most powerful box mods, such as: B. variable wattage, temperature control or customizable TCR settings.

However, there are a variety of protections built into the device that prevent the device from shorting out and vaping at dangerously low voltages and are extremely helpful in extending the overall life of the device and its internal battery.

As there is no way to adjust the Smok Novo’s power settings, the only way to alter your vaping experience is to play around with the wide range of strengths available for the flavor of your choice until you find that coveted sweet spot have found.

The Smok Novo also lacks the option to adjust your airflow, which is by no means standard, although newer devices are slowly emerging with this feature, so it would have been nice to see something similar on the Novo.

A gurgling vape tank is one of the most annoying problems you can deal with as a vaper. It’s not so much that the noise itself is annoying; The problem really is what the gurgling sound means. It means there’s excess e-liquid trapped somewhere in your vaping device, whether it’s in your tank’s air duct or in the coil assembly. The e-liquid will block airflow and hinder your device’s vapor production. Gurgling is also usually the first sign that your tank’s atomizer coil is flooded and the tank is about to leak. If you don’t fix the minor annoyance, you can quickly end up with a lot of lost e-liquid.

In this article, we will teach you how to fix a gurgling vape tank.

What causes a vape tank to gurgle?

Gurgling can occur with both sub-ohm tanks and pod systems. This happens because e-liquid gets caught somewhere in the tank’s air path – either in the intake vents or more commonly in the chimney leading out of the tank. The e-liquid blocks the airflow, causing the tank to bubble while vaping. If you can figure out what’s causing the e-liquid to pool, you’ll fix the gurgling.

We will discuss all of the different things that can cause a vape tank to gurgle in this article. You may need to do a bit of troubleshooting to determine which scenario applies to you, but once you figure it out, you’ll find that the gurgle problem is pretty easy to fix.

Remove excess e-liquid from your tank’s chimney

A modern sub-ohm tank will have a wide smokestack to facilitate smooth airflow and encourage the production of large clouds of vapor. If your tank is producing vapor with a large droplet size – we’ll discuss this in more detail shortly – some of the vapor can condense while still in the stack and form droplets that drip back to the evaporator coil. The droplets collect on top of the coil, causing a gurgling and popping sound as you vaporize. The easiest way to prevent this is to get a new tank, which we’ll get to shortly.

Until you get a new tank, however, you must do something to stop the tank gurgling. The best way to do this is to roll up a paper towel and slip it through the mouthpiece of your tank. Run the paper towel all the way down the tank’s flue until it touches the top of the atomizer coil. The paper towel will soak up the accumulated e-liquid and temporarily eliminate the gurgling.

Upgrade to a more modern tank

When vaping, does the vapor have a “wet” character in your mouth? Do you sometimes feel like you’re almost drinking your e-liquid when you take a really deep, long hit? Until recently, many sub-ohm tanks used “Clapton” style twisted wires to produce large clouds of vapor. Clapton wire has a large surface area, which allows for excellent vapor production. However, the disadvantage of the Clapton wire is that it produces vapor with a large droplet size. This will lead to condensation in the chimney of your tank. Condensation causes e-liquid to build up on your atomizer coil and this causes gurgling, popping and spitting. You can get the same cloud production without the associated problems if you use a tank with a mesh coil instead.

Some of the most popular mesh coil tanks at the time of writing are:

A mesh coil has a large surface area like a Clapton coil, but the metal isn’t nearly as thick and heavy. Mesh Coils produce vapor with much smaller droplets, so the vapor has a “dry” character and is not prone to condensing in your tank’s stack. Problems such as gurgling, popping and spitting are practically non-existent with mesh coils.

Use less air pressure when vaping

If you’re using a pod system, the most likely reason your device is gurgling is because you’re blowing too hard. Over-inflation will disrupt your device’s normal airflow and push extra e-liquid into the pod’s atomizer coil assembly. The e-liquid then begins to seep out of the pod’s air intake vents, or it travels up through the pod’s stack and into your mouth. Either way, your pod system will gurgle as you vape.

If you want your pod system to hit harder, using extra air pressure when you draw isn’t the way to go about it. If you blow harder, your device will not produce warmer vapor or larger clouds. The way to get the biggest clouds out of your pod system is to take long, slow hits. If you find yourself getting weak puffs from your pod system, make sure you are using nicotine salt e-juice with a high nicotine strength.

You can also consider upgrading to a more powerful refillable pod system that produces bigger, more satisfying clouds. Some of the most popular refillable pod systems at the time of writing are:

Clean your pod between refills

If you use a refillable pod system, you already know that cleaning your pods is next to impossible as there is no real way to disassemble and reassemble a pod like you can with a vape tank. With a standard vape tank, cleaning is an important part of your regular maintenance routine as it can help prevent issues like gurgling.

However, you can’t clean a vape pod this way, so you’ll need to find another way to remove excess e-juice from your pod – and the method for doing so is actually quite simple. When it’s time to refill your pod, remove it from the device. Hold a paper towel over the bottom of the pod and blow forcefully through the pod’s mouthpiece. Blowing through the mouthpiece forces the excess e-liquid out of the pod’s inlet ports and into the paper towel. If you do this every time you refill your pod, you will rarely experience a gurgling sound when vaping.

Clean your tank between refills

As we just mentioned, keeping your hardware clean is just as important, whether you’re using a pod system or a mod with a sub-ohm tank. If you are a tank user, the great thing is that routine cleaning of a vape tank is extremely easy and adds just a few seconds to the time it takes to change your coil. If you take your tank apart to change the coil, give the tank a quick rinse in your sink.

After rinsing your tank, dry it thoroughly with a paper towel. Install and prime a new coil, then carefully reassemble the tank, being careful not to cross the threads. Flushing the tank will remove any excess e-liquid that may have lodged in the tank’s stack and vents. If you also follow all of the other advice in this article, keeping your tank clean will further help minimize gurgling.

Do not use All-PG Vape Juice

With almost any modern vaping device, the worst thing you can do is use a pure PG vape juice. Propylene Glycol and Vegetable Glycerin are the two base liquids used to make Vape Juice. PG is much thinner than VG. It also produces smaller clouds of vapor and has a thin, delicate mouthfeel. Most vapers like the bigger clouds and fuller mouth that VG offers, so most e-liquids contain at least 50 percent VG.

VG is much more viscous than PG. To support an e-liquid with a significant amount of VG, a tank’s atomizer coil needs to have large openings that allow the wick to efficiently absorb the thick e-liquid – and since almost all e-liquid these days contains at least 50 percent VG, Most tanks have large wick openings to hold the thick e-liquid.

100% PG e-liquids are still available today. They are mainly made by Chinese e-liquid manufacturers and are intended for use in small cigarette-shaped vapor devices called cigalikes. Unless you are using a cigalike, you should not be using 100 percent PG e-liquid. In a more modern vaping device, the thin e-liquid seeps through the wicking holes of the atomizer coil and floods the coil, causing gurgling and leaking.

If you’re using an all-in-one mod, consider upgrading

In the mid-2010s, all-in-one vaping devices with built-in tanks were briefly popular. In this type of vaping device, the mouthpiece and chimney are the same unit, and the coil is connected to the bottom of the chimney. Because the coil and chimney are both narrow and submerged in the tank, this type of vaping device is extremely prone to gurgling. That’s because a submerged coil has poor airflow, and if your coil has poor airflow, you’ll need to apply more pressure when inhaling to get a satisfactory amount of vapor. As you just learned, using too much air pressure when inhaling will result in excess e-liquid being drawn into the coil unit.

All-in-one vaping devices were a good idea in their day, but those days are gone. Stop the gurgle with a more modern device from the vape starter kit section of our website.

It is highly recommended that vaping enthusiasts take care of their coils. You can do this by using the appropriate vape juice without draining your vape and vaping at the right wattage. Replacing coils can be quite expensive, especially if you don’t know how to fix a burned coil. Well, if at some point you experience a burnt taste from vape, there’s no longer a need to throw away your vape as there are some reliable hacks to fix it.

Most young vapers hardly know how to fix a burned coil unless they are DIY. But first you need to understand what causes a burned coil before you can fix it.

How to Repair a Burnt Coil: Causes of a Burnt Coil

Coils, like everything else, don’t last forever. There is no set time for a coil’s lifespan, but it has been proven to wear out as you vape. Therefore, experienced vapers who vape a lot need to replace the coils in less time compared to beginners.

Poor Quality or Poorly Installed Wick – Let’s rewind a little. The wick is a cotton or cloth component that absorbs vape juice and brings it closer to the coil. In fact, it is constantly in contact with the coil. If it is of poor quality or installed incorrectly, it will not work properly and you will start to experience a burnt taste.

Insufficient Vapor Juice – Being aware of these causes is even better than learning how to fix a burned coil. Vaping while the tank or cartridge is low on e-juice will stress the wick as some parts do not absorb e-juice well. Sooner or later you will get a burnt taste while vaping.

Very Frequent Vaping – The more you vape, the more stress you put on the wick and coil. As previously mentioned, Chain Steamers will periodically need to repair and eventually replace a burned Coil. You have no choice in the end.

How to fix a burnt coil: solutions to a burnt coil

Let’s look at how to fix a burnt coil. First carefully remove the sub ohm coil or something else and also the wick. If you’re not careful you can end up damaging the coil and this will force you to do what you wanted to avoid in the first place.

Meanwhile, have hot water in a bowl ready to submerge the coil. Put it in and leave it on for a few minutes. If you are looking forward to learning how to fix burnt coil vape, this step is crucial as it loosens the burnt vape juice or dirt from the wick.

Prepare a separate bowl of cold water. So carefully remove the coil from the hot water and dip it into the cold water. This will help any remaining residue fall off and your coil will be clean again.

If you’ve done this and still have that annoying burnt taste, you can clean it with vinegar or lemon juice in hot water. This will remove stubborn deposits but shorten coil life as it is corrosive. Therefore it is not the first option.

How to prevent a burnt coil

Simply put, taking good care of your coil and vaping moderately will save you a lot of money. Even after you learn how to fix a burned coil, you won’t have to go through the process as often or buy new coils regularly if you take care of the entire vape device.

A burning taste of vapor is definitely annoying. But with the knowledge above on how to fix a burned coil, you can easily boost your vaping experience whenever the need arises.

5 signs that it’s time to change your vape coil

Whether you’re brand new to vaping or have been using vape for a while, it’s good to know the telltale sales numbers when it’s time to change your coil.

Coils don’t last forever, and they’re not supposed to. If you take good care of your e-cigarette and clean the parts regularly, they can last longer than usual, but sooner or later they will need to be replaced. There are some noticeable ways your vape will tell you it needs a new coil, as well as some less obvious ones.

1. Your vape tastes burnt

This is probably the most noticeable thing that will tell you that your coil needs replacing and something most vapers will experience. When you vape you will get a really horrible “burnt” taste in your throat – sharp and unpleasant, even nauseating.

If a vape tastes like this, it’s definitely time for a vape coil replacement as you’ve probably burned the wick and coil materials and can’t salvage them.

2. Your e-cigarette gurgles

Some e-cigarettes tend to gurgling, but this noise could be a sign of something else as well. It could be that there is a real problem with your vape, but it could also be something as simple as flooding your tank and needing the coil replaced.

The gurgling can occur if your coil has not been properly placed in your vape and this could be the case if you have just replaced the coil and are hearing this noise. You could try unscrewing and reattaching the spool and making sure the holes all line up properly. However, if you still hear a noticeable gurgling noise when vaping, it’s time for an e-cigarette coil replacement. If this does not solve the problem, contact our customer service team.

3. Your vape tastes “strange”

This one is a bit harder to define, but another one that most vapers will come across. You’ll be using the same e-liquids you used to, but find that they just don’t hit the spot anymore. Maybe they taste very bland, maybe they taste a bit strange, or maybe they have no taste at all. You might even be able to tell the difference from the e-liquid itself – it might look darker than normal, like it might take on different colors when you put it in the tank.

Chances are your coil and wick are so saturated with other e-liquids that they can no longer provide you with the right flavor. Again, replacing the e-cigarette coil will solve your problem.

4. Your spool has run out

This all depends on your personal vape usage. It’s not really about how long you’ve had a coil, it’s about how often you vape (and the occasional e-liquid you use!). If you are a heavy vaper and use your vape many times a day, you may need to change the coil every few days. If you are a regular vaper but not particularly heavy, it may take a week or two. Infrequent or occasional vapers might find that they only need to change their coils every four weeks. Regardless of your vaping habits, however, you should consider an e-cigarette coil replacement at least once a month.

Also, if you’re not sure how often you need to change it based on your habit, start keeping a journal of when you put in a new coil, what e-liquid you use, and when you realize it’s starting to go bad to taste or smell or strange. That way you’ll know when you’ve completely burned it out and you can avoid it happening again.

If e-liquid is leaking into your battery or leaking from the tank, it’s time to give your e-cigarette a thorough check-up. Take it apart, clean it thoroughly, check if the batteries are good, then carefully reassemble it. If it’s still leaking, take the coil out and examine it and the source of the leak could be pretty obvious. Whether this is the case or not, replacing the vape coil is the next thing to try. Hopefully changing your vape coil will save you from buying a whole new device.

We’ve also heard people say that if the vapor doesn’t look quite right, if they can’t blow big clouds, or if the wick “sounds” a certain way, they can say the coils need replacing! What signs do you look for when it’s time to replace your vape coil?