Pal 2000 Pool Light Replacement? The 127 Detailed Answer

VOLTAGE 12V vs. 120V – Pool lights are designed to operate on 12V or 120V. In some areas of the country, local codes require a low voltage 12V lamp, while in other areas it is fine to use a 120V lamp. Before installing a light, find out what your local codes require. If you install a 12V light fixture, you need to install a transformer to convert the 120V house voltage to 12V. If you are replacing an existing bulb and don’t know its voltage, you can try the following techniques to find this information: 1.) Look on the face of the bulb for the voltage rating. 2.) See if you have wired a transformer in front of the light. If you have a transformer you will have a 12v light. 3.) Check the back of the light housing where the cable connects to the light, there is a label specification of your light there. The brightness of 12V and 120V is the same. Some manufacturers do not recommend using a 12V light if the light’s cord will be longer than 100 feet as there may be a voltage drop. Note: Brightness, which is discussed in more detail below, is a function of light output, not voltage. The brightness of a 12V or a 120V lamp is the same.

Blown pool bulb?

How to change an underwater lightbulb:

1. Turn off power at the circuit breaker and all other switches as well.

2. There is no need to lower the water level. In almost all lights there is enough cable coiled up in the light niche so that the light can be taken to the end stone for repairs. Remove the single stainless steel screw at the top of the light (at 12 o’clock). Once removed, use a flathead screwdriver to pry the bracket out of the niche. Most lights have a tab at the bottom (at 6 o’clock) that fits into a slot on the niche or light body. You may have to pry and wiggle the lamp to release the tab and remove the bracket once the screw is removed. After removing above water, lift it onto the pool deck.

3. To get inside the bracket, use quality tools of the right size not to damage any of the soft metal screws, bolts, etc. On very old mounts, screws can easily break or become corroded from years of water and chemical exposure. Older model lights have 8 brass screws around the bracket that tighten on the tabs. Newer models have a clamp band with just a bolt or bolt/nut. Use a #2 or #3 Phillips screwdriver to remove the screws and, for clamp straps, use a 5/16 inch socket wrench. After the clamp or screws loosen, remove the light hood or light ring. Next, use a small flat head screwdriver to gently pry the glass lens out of the front of the bracket.

4. After removing the lens, remove the bulb. Most unscrew counter-clockwise. Some spa lights or small halogen pool lights have small bulbs that you push in and then turn counterclockwise a quarter turn to remove. Regardless of the type, be careful when removing the bulb, old bulbs can crack at the base when removed. It is a good idea to cover the bulb with a soft cloth before rotating to avoid injury. After removing the bulb, use the cloth to wipe clean and dry all interior surfaces. Wrap the new bulb or LED bulb in a soft cloth, both for safety and to keep finger grease off the bulb. Thread the new bulb, made specifically for the light, and pull it into the base until it stops.

5. Before reassembling the lamp, turn the lamp so you can see the bulb and turn on the power very briefly (for 1-2 seconds) to check if the bulb/lamp is working. Locate the printed instructions on the lens for proper alignment of the lens on the mount. Place the lens back on the mount using a NEW lens gasket. This is the rubber gasket around the lens, about 8 inches in diameter. The gasket only fits around the lens, it doesn’t wrap around the bezel or light ring, and no lubricant is required. Complete the assembly of the mount by clamping the bezel over the lens using the light weight screws or clamp strap. Screws should be tightened in a pattern to ensure even tightening.

6. Place the light under water and check for air leaks (a few bubbles may detach from the mounting ring). If no bubbles come out of your gasket, you have made a good seal.

7. Leaning far over the edge of the basin, reinsert the fitting into the niche. First wrap the cable around the back of the mount, then locate the bottom tab (on the mount) and the tab receiver (in the niche). Align and place the tab in position and press the bracket flush into the niche. Then it’s just the “not always easy” task of getting the pool light screw back through the light surround ring and into the threaded hole in the niche. A mask or glasses can help to see. Just tighten the screw firmly (not too tight) and then test your light again.

You can be electrocuted by a pool light in a swimming pool. It can cause serious injury and even death. An experienced electrocution attorney can help victims and families recover damages for personal injury or wrongful death to which they are entitled by law.

How can you get electrocuted by a pool light?

You can be electrocuted by a pool light if faulty wiring or a defective lighting fixture causes an electrical current to be released into the water and you come into contact with the electrified water.

What happens if you get electrocuted by a pool light?

Death or severe injuries can result. It is possible for a person to die instantly or be electrocuted in the water if the electric current paralyzes a person and causes them to drown.

Can you claim compensation for pain and suffering?

You may be able to recover pain and suffering damages from any responsible party if you or a loved one has suffered an electric shock injury.

Can I claim damages from unlawful homicide?

If a family member or loved one loses their life after being electrocuted by a pool light, your family may be entitled to wrongful death damages from any responsible party for the pain and suffering of your loved one, for the loss of your companionship and camaraderie Reclaim family and for funeral expenses.

Who are responsible if you get electrocuted by a pool light?

There may be several responsible parties, such as the pool owner or maintenance company that you would sue in a court of law for pain and suffering, economic loss, or wrongful death damages.

Parties who may be responsible if you or a loved one are injured or lose their life depend on where the pool is located, who owns it, and who is responsible for installing and maintaining its electrical equipment and wiring.

These parties may include:

The owner of a hotel pool

The owner of an apartment complex pool

The owner of a community pool

The owner of a gym pool

The school pool owner

The owner of a garden pool

The owner of an enclosed pool at someone’s home

The company responsible for maintaining the pool

The company that installed the electrical equipment of the pool

The manufacturer of the electrical equipment of the pool

The company that inspected and determined the pool complied with the regulations

The electrician and/or electrical contractor and/or licensed electrician who performed the electrical work on the pool

What compensation is available?

The compensation you may be able to claim for damages and/or wrongful death depends on: (1) the injuries sustained; (2) whether a family member or loved one was killed; (3) current and future medical needs; (4) incapacity for work; (5) income before electrocution; and (6) your electrocution attorney’s experience, track record, and reputation.

Your choice of lawyer can have a significant impact on the amount of compensation you can claim back. Insurance companies keep track and know which lawyers are going to court and winning – and which are avoiding the courtroom and “quickly settling cases”.

Lawyers who have a reputation for going to court can settle cases for more money and often much faster.

causes

You can be electrocuted by a pool light as a result of: (1) faulty electrical wiring; (2) defective lighting equipment; (3) negligently maintained lighting equipment; (4) defective lighting equipment; (5) lack of GFCI (Ground-Fault Circuit-Interrupters) protection; (6) Lighting equipment that does not comply with applicable city and state safety codes, including the National Electric Code.

danger sign

When swimming in a lighted pool, be aware of the following danger signs: (1) a tingling sensation, muscle spasms, and/or an inability to move when near a light; (2) swimmers panic and quickly move away from a pool light; and (3) pool lights flicker or operate intermittently.

How to help when someone is electrocuted by a pool light

Here are the security measures you can take:

DO NOT ENTER THE WATER to help someone in need

Immediately turn off/disconnect all power to the pool lights and the surrounding area

Extend a carbon fiber pole (such as a fiberglass shepherd’s crook/lifehook – which are not conductors) towards the person in the water to grab or entangle the person’s body and pull (face up) in safety

Get out of the water, but DO NOT USE METAL CONDUCTORS OR ANYTHING THAT MIGHT CONDUCT ELECTRICITY

Get help from an experienced electrocution attorney

If you or someone you love has been the victim of serious injury or death from electrocution, you can call and speak to Jeff Feldman, perhaps the most experienced electrocution attorney in the country. Jeff has served cases involving low hanging power lines and against state utilities across the country. You can call toll-free at (800) 548-0043 for a free consultation.

Pool lighting has the ability to transform your outdoor space, highlighting function and enhancing your swimming experience.

Well-designed lighting gives you the opportunity to change the mood of your garden and highlight architectural features such as a waterfall, spa or stone wall of your pool. It also provides night vision, improves the safety of your pool and extends its usage time.

What is LED lighting?

Light Emitting Diode (LED) lights are one of the most popular fixtures for swimming pools. As energy efficiency has increased, LED technology has become a standard feature, slowly replacing incandescent bulbs.

The lights work by pumping voltage through the semiconductor that emits light, while incandescent and halogen lamps rely on burning filaments. LED lights work simply by plugging directly into the power source.

The advantages of LED lighting

Installing LED lighting in your swimming pool offers several benefits, including:

energy efficiency

LED lights are inherently more expensive than halogen or incandescent bulbs, they save you in the long run due to their energy efficiency. Incandescent bulbs typically have an output of 300 to 500 watts, while LED bulbs use only 42 watts.

By installing LED lights in your swimming pool, you will see greater savings on your electricity bills.

Greater lifespan

LED lights are known for their longevity of well over 20,000 hours. Quality LED brand names can last 10 years or more. This is reduced for these lower cost products.

Low maintenance

Because the bulbs last longer than other lighting fixtures, LED products typically require fewer replacements because they contain robust diodes. That means you spend more time enjoying your well-lit pool and less time maintaining it.

Visual effects

LED lights are available in a variety of colors giving you the ability to create visual effects to set the mood. Highlighting features of your pool can be achieved through the quality of light and the even, deep glow that LED lamps provide. These lights can be changed at the touch of a button.

automation

Unlike halogen lights, LED lights can be automated, with most models offering an optional remote control. Most also have built-in smartphone apps for those who prefer a more tech-savvy experience.

Disadvantages of LED lighting

One of the main disadvantages of LED lighting over other lights such as halogen models is that it is not serviceable. This means that if the internal components of the LED lights fail, the socket will need to be replaced. While the light itself can last up to 10-12 years, the other components likely won’t last nearly as long and will degrade over time.

Cost is another disadvantage of LED lights. Apart from the higher initial cost of the lights, LED lighting requires special transformers and converters to use the right voltage between 12 and 32V. This requires additional electronic equipment, which increases the overall cost. Luckily, these transformers aren’t too expensive, and they’re generally pretty reliable.

LED lights are also somewhat prone to leaking, just like halogen fixtures. Thankfully, the nifty resin-filled LED lights largely solve this problem. If you need to replace a broken LED socket or leaked pool light, you can swap it out for the resin-filled LED version.

For more pool tips and advice, visit our learning library.

If you are considering an inground pool, you are probably also considering installing underwater pool lights. Because we work with hundreds of people throughout Virginia, Maryland and West Virginia each year, we have the opportunity to answer countless questions about pool lighting. In this article, we’re going to cover some of the most popular in-ground pool lighting questions that we receive on a daily basis.

What should I know about pool lights?

Illuminating your pool allows you to swim at night with multicolored ambient light. LED pool lights allow you to change color with a switch. Pool lighting must be installed during construction. Smaller LED lights cost $700 to $900 installed, and fiber optics cost $1,300 to $1,700. The only maintenance required is replacing the bulb.

Why should I light my pool?

First of all, lighting your pool allows you to take full advantage of your pool day and night. Many people find night swimming a wonderful experience, but it just isn’t the same without the ambiance of the reflective light that an underwater light provides.

Lighting up your in-ground pool will also provide peace of mind when watching little ones swim after dark, as it will provide better visibility throughout the pool.

Do pool lights need to be installed during construction or can they be added after the fact?

Some pool accessories can be added later, but pool lights don’t offer that flexibility…not without major renovations, anyway.

We would suggest if you are considering remote pool lighting it is best to have it installed during the construction phase.

How many lights do I need?

It depends on the type of light, but we currently use the smaller LED lights like the Globright or Pal 2000 in our fiberglass pools and recommend that at least one light adequately illuminates a pool up to 30 feet long. Pools longer than 30 feet require two lights. Please note this is a bare minimum, most people end up getting two lights in each pool and some even have us install three on very large pools.

What lighting options do I have and what are the pros and cons of each?

The predominant pool lighting on the market today is LED, but fiber optic lighting as well as incandescent lighting are also available. Let’s take a closer look at each one.

light-emitting diodes

LED stands for Light Emitting Diodes, which are made to glow by the movement of electrons in a semiconductor material.

LEDs have no filaments and therefore do not emit heat.

LEDs also change color and have multiple light show settings.

LED bulbs have a very long lifespan… around 30,000 hours compared to the 5,000 hours of incandescent bulbs and the 6,000 hours of fiber optics. That equates to SIX bulb replacements and FIVE fiber optic replacements.

fiber optics

Fiber optic pool lights peaked in the early 2000s and have lost market share with the widespread adoption of LED technology.

The fiber optic pool light design is unique in that the bulb is actually housed in a drying box on the pool deck. The light from this bulb is guided through fiber optic cables, a special fixture in the pool wall where the cable ends and the light shines into the pool.

Some fiber optic lights have a color wheel located in the box that the light shines through, causing the light to change color in the pool.

The main disadvantage of fiber optic lamps is that they are simply the least bright of all lighting options.

As we will see later, they are also very expensive, especially for the amount of light they put out.

lightbulbs

Incandescent light bulbs work by running an electric current through a wire known as a filament to heat up. The filament glows and produces the bright light of an incandescent lamp.

The first disadvantage of incandescent bulbs is that in order to change color, a colored lens needs to be placed over the pool light in the pool. That was fine twenty years ago, but a bit antiquated today.

Second, the lifespan of the bulb is much shorter than that of LED bulbs.

How much do recessed pool lights cost?

At the time of writing, full-size LED pool lights, such as those typically installed in vinyl liner or concrete pools, typically cost between $1,000 and $1,500.

The smaller LED lights like the Pentair Globrite or PAL 2000 typically cost between $700 and $900 installed.

Fiber optic pool lights typically cost between $1,300 and $1,700.

Full size pool light bulbs are usually in the $450-$650 range.

What maintenance is required?

The only maintenance required for any pool light is replacing the light bulb.

Regardless of the type of light, you should never have to lower the water level in the pool to replace the bulb. In some cases, you can loosen a single screw, raise the bulb housing above water level, and replace the bulb. This process only takes five to ten minutes.

Other lights, on the other hand, require the entire housing to be replaced, which takes a little longer but still isn’t much of an ordeal, especially considering the average light bulb lasts many, many years.

Replacing fiber optic lamps is very easy as you simply remove the housing cover that is on or near the patio and snap in a new lamp.

The cost of replacing the bulb at the time of writing this article is as follows:

Large LED $450 to $650

Small LED $50-$350 depending on model

Fiberglass $20-$60

Incandescent $30-$70

Are pool lights safe?

In short, yes, they are extremely safe as long as they are installed to manufacturer specifications and comply with local building codes.

Modern pool lighting, properly installed, is virtually risk free.

Well we hope you found this informative and wish you the best of luck in your quest to find the right pool light for you. Check out our article on pool lighting and other pool options.

As always, you can leave comments or questions below.

Next:

7 Pool Extras That Won’t Break the Budget

What is the best small fiberglass pool for your needs? Cost, sizes, features

Editor’s Note: This blog article was updated on February 18, 2020.

There are countless options for you when you decide to build your new inground pool and you need to decide what is an option and what should be done immediately?

Pool lighting falls into both categories, both now and as a later option. You must install the lights right away so they are in the pool wall, but you can upgrade to colored lighting in the future.

Energy saving and longevity

With an LED light you save about 75% of your energy consumption compared to a comparable incandescent lamp. Keep in mind that LED pool lights cost more on average than a simple incandescent bulb, so your savings won’t start until you’ve recouped the extra money you spent on the LED lights.

LED pool lights last much longer than a standard light. Traditional incandescent pool lights last around 5,000 hours, while an LED light lasts over 30,000 hours. . . provided that water does not enter and short-circuit the device.

cool factor

LED lights make it very easy to add color to your pool lighting. Provided you have the alcoves (device that holds your light in the pool wall) you can swap out white LED or white incandescent bulbs for color changing LED lights. These lights are generally controlled by an automation system, allowing you to choose the color you want. Typically there are 5 fixed color choices and 7 pre-programmed light sequences to choose from.

These lights can be replaced by any pool builder who performs pool services.

safety aspects

Many of the LED pool lights on the market today are available in both mains voltage and low voltage. Inground pool builders are beginning to move to low-voltage LED lights because they are easier to install, have less liability, and offer the same functionality as their older mains-voltage counterparts.

Ultimately, most inground pool builders are moving towards LED pool lighting as the standard for all new inground pools. We recommend them even if you don’t get them with the color change options. As always, make sure you get multiple pool quotes and make sure your pool builders do pool services as they are better informed.

I wasn’t sure what to do but after reading this article I feel better knowing it’s an easy procedure to fix.”

…”

“I’m a first time pool owner and I’m still learning about the whole process of the pool. When it comes to water and electrics,

In-ground pool lights are prone to leaks from the conduit, which is the tube that carries the light cord from the lamp to the junction box. The pool’s light pipe is a ¾” or 1″ gray PVC pipe that runs below the deck.

Since the connection point of the tube with the light niche is not sealed, water can penetrate the tube. In some cases, water in the line can freeze solid, rupturing the line and spilling out of the pool. In other cases, the line may rupture during deck laying or from earth movement or sliding plates.

Is the pool light leaking?

The way to detect a light leak in the pool is to continue to run the pool on only the main drain (close or plug the skimmer) and allow the water level in the pool to drop. If the water level appears to be stabilizing at the level of the light fixture, or more specifically just a few inches below the top of the light fixture, there may be a line leak. To be on the safe side, you can add a few inches of water and shut off the pump by plugging the skimmers, returns, and main drain lines, as well as any other pool plumbing lines, with expansion plugs.

If an in-ground shotcrete pool continues to leak even though all plumbing is tightly sealed and the pump is off, it means there is a leak in the pool shell or pool light. Vinyl liner pools must eliminate leaks in the liner or anywhere the liner has been intentionally cut; such as steps, skimmer, return, drain and pool lighting.

For more advanced pool light leak detection, Anderson Mfg. Make a pool light tester that you can use to caulk the pool wall and add leak test dye to see if it’s being sucked out of the line.

how deep can you go

If the water level continues to fall below half light, you may have a leak in the line, but there is another leak elsewhere as well. A leak in the pool light guide will only leak to the connector on the top rear of the light niche where the duct connects.

Pool light niche leaking?

Pool light niches rarely leak, it is extremely rare for a pool light to leak through the light niche shell or around the light niche – 99% of the time a pool light leaks it is water leaking through the light guide. However, with vinyl pools, the lightweight niche seal around the niche is sealed to the pool wall, which has greater potential for leakage.

Water in the pool lights?

If there is water in the lens of the pool light, which you can usually see from the deck, it doesn’t mean the light is leaking, but it does mean the lamp seal is broken and water is seeping inside and it’s surrounding the bulb. This could be a potentially dangerous situation that should be addressed, but it is not the cause of the pool leak.

Fixing a leak in a pool light pipe

Relax, we won’t dig up the broken light guide, there are a few ways to seal the light guide inside the pool where it connects to the back of the light alcove.

SILICONE: At medium or low water levels, squirt silicone rubber up the pipe and around where the light wire enters the connector. Clean the areas beforehand to improve bonding and sealing. Makes a fairly permanent fix, but can be a hassle if you need to replace the entire light at some point in the future – you’ll have to dig everything up.

POOL PUTTY: Mix up half of the epoxy/resin pool putty and wrap it around the (cleaned) light wire and connector fitting. Make a cone of putty that will seal against the niche, cord, and port. Refill the pool and leave the light on deck for 24 hours to allow the putty to dry. Reinstall the light carefully to avoid disturbing the putty.

LIGHT WIRE STOPPER: For the most permanent solution to a pool light pipe leak, seal the hole in the light niche with a light wire stopper. Manufactured in two sizes to fit 3/4″ or 1″ hole, with a through hole for the light cord to pass through. Just press it firmly to prevent water from entering the line. Also good for new pools – to prevent the light guide from leaking from the outset!

Rob Cox

InTheSwim blog editor

^this way to go Tim! Please give us an update if you have switched to LED. @OP, any 120VAC LED bulb should work. Just make sure it matches your existing fixture. Also, replacing the gasket every time you open the fixture and/or replace the bulb is a MUST. Didn’t realize there was a bit of water in our light in the spa until the water was drained. Apparently the GFCI security feature has failed and the test button is considered non-functional! But then again, I can’t remember the last time we turned on the light. Further inspection reveals a very stiff cable and appears to be brittle with age. So I replaced the fixture and opted for 12VAC color changing LEDs as I have a Malibu 300 watt stepdown x’former. EDIT: When in doubt, INYOPools will point you in the right direction. Thank you Patrick

Are your pool lights not working?

If you have a swimming pool in your garden or on your property, you probably have lighting installed in it as well. Swimming pool lighting can add a lot of beauty to your pool along with the ability to safely use and enjoy it 24/7. However, after a while, you may find that your light flickers or won’t turn on. While you may think it’s time to drain your pool and replace the lightbulb, which can be an extremely tedious and expensive process, you may be surprised to learn that you may just have another factor in your electrical system need repairing. The trick is to troubleshoot a few things to figure out what the problem is before removing the water from your pool.

Easy pool light troubleshooting

The first thing you should do is put on your swimming goggles and go underwater to check the light yourself. Try to see if you can shake the ring holding the light fixture into the pool itself. If it moves slightly when you touch it or move water past it, try plunging a larger Phillips screwdriver back down to tighten it.

Put on your swimming goggles and head underwater to check out the light for yourself. Try to see if you can shake the ring holding the light fixture into the pool itself. If it moves slightly when you touch it or move water past it, try plunging a larger Phillips screwdriver back down to tighten it. If that doesn’t work, try checking your light fixture to see if you can spot water in it. If there is water in the faucet itself, you may have a leak. This is usually due to a bad lens gasket, which is a rubber seal between the lens and the body. However, this can also be due to the fact that the pipe seal wears out over time. Unfortunately, fixing any of these issues requires draining the pool.

, try checking your fixture to see if you can spot water in it. If there is water in the faucet itself, you may have a leak. This is usually due to a bad lens gasket, which is a rubber seal between the lens and the body. However, this can also be due to the fact that the pipe seal wears out over time. Unfortunately, fixing any of these issues requires draining the pool. If you finally fix the fixture and the light didn’t turn on, your bulb may have burned out. Remove the bulb from the holder and shake it near your ear. If you hear the filament run into the sides of the bulb, your bulb is dead and needs to be replaced.

More difficult troubleshooting

If replacing your lightbulb doesn’t work and you’ve made sure all of your gaskets are in good condition, you may have tripped the circuit breaker. Generally, this happens when you plug in or turn on a new device into an outlet that is on the same circuit as your pool lights. Check the circuit breaker panel, which is usually located on the side of your home. If your pool light breaker has tripped, unplug everything you just turned on or plugged in and reset the breaker by turning it all the way off and then back on.

If that doesn’t work, you may have a bad breaker. If this is the case, it is highly recommended that you call a Marietta electrician to have it replaced.

Finally, there’s another possible option: you’ve tripped your RCD. Better known as GFCI, this is a device used to reduce the hazard in installations that have a higher than usual risk of electrocution. They are usually found on electrical outlets in bathrooms and kitchens, and you can usually find them outdoors as well. If you have GFCI sockets on your pool lighting circuit, try resetting them. If that doesn’t work, you may need to replace it.

At Lighting Bug Electric we offer a range of pool lighting services in Marietta and Atlanta. If you have problems with your pool lighting, contact our experienced and competent team. We work quickly and efficiently to diagnose the problem and provide permanent solutions. In addition, we offer competitive prices for every budget.

If you need help with an electrical problem, Lightning Bug Electric can provide you with quality service! Call us today at (404) 471-3847 to schedule an appointment.