Are you looking for an answer to the topic “pool table cushion replacement“? We answer all your questions at the website https://chewathai27.com/ppa in category: https://chewathai27.com/ppa/blog. You will find the answer right below.
Table of Contents
How much does it cost to put new fabric on a pool table?
It costs $300 on average to refelt a pool table, with a typical price range of $250 to $300. You may pay as little as $150 or as much as $500. Pool tables come in three sizes, and size affects the price. The cost of pool table refelting is fairly evenly split between materials and labor.
How do you check a pool table cushion?
Feel – Using your fingers, run your hands around and under the table rails, where the edges hang over the table’s playing surface. You are feeling for worn grooves and tracks under the felt. If you find any, this is an indication of worn cushions.
How much does it cost to Refelt a 7ft pool table?
The average cost to refelt a pool table is $366 depending on the table’s size and the quality of the fabric. Installing new felt on a 7 or 8-foot pool table costs $265 to $500, and $280 to $550 on a 9-foot table. Some refelting services charge $100 less if you buy your own felt.
How to Replace Pool Table Cushions in 1 Hour
Pool table refelting costs on average between $282 and $434, depending on the size of the table. Felt replacement includes the pool cloth, removing the staples, attaching the felt and leveling. Add $60-$180 if you’re also replacing the bumpers at the same time, and $200 more to disassemble, move, and reassemble.
Pool table felt comes in a variety of grades, ranging in average from $130 to $335. Labor costs average $125, with extended pool table installations costing up to $280. If you’re not sure what repairs you need, a standard service call and retune will cost around $95. Voting will also help you determine if you have a 1 or 3 piece slate pool table.
Refelt Pool Table Cost National Average Cost $366 Minimum Cost $255 Maximum Cost $590 Average Range $282 to $434
Most pool table repair services will have a brochure or online listing of the benefits of each and the variety of colors offered. Moving your pool table will remove the felt anyway, so this is an excellent time to re-felt it. After the restoration, they also check the height of the pool table and readjust it to make sure it’s perfectly flat.
Table of Contents
Pool table felt replacement costs
The average felt replacement for a 7 foot pool table costs $265 to $450, while refelting an 8 foot pool table costs $270 to $500. Prices depend on the quality of the fabric, with a difference of around $10 to $50 per additional foot of table length.
Pool Table Felt Replacement Cost Size Good Better Best 7 foot table $265 $350 $450 8 foot table $270 $360 $500 9 foot table $280 $375 $550
Installation of pool table felt
There are several types of billiard tablecloths ranging in price from $130 for Teflon felt to $335 for a quality worsted cloth. The felt you choose should relate to the quality of your pool table; However, it is never recommended to go with the cheapest. A high-quality pool table felt lasts about 10 years with proper care.
Pool Table Felt Installation Felt Type Fabric Cost Labor Cost Total Cost 8FT Championship Invitational Teflon Felt (Cloth) $130 $125 $255 8FT Proline 303 Teflon Felt (Cloth) $160 $125 $285 8FT Proline 404 Felt (Cloth) 165 $125 $290 $8FT ProForm Felt (cloth) 215 $125 $340 $Simonis 860 Felt (worsted) 315 $125 $440 $8FT Simonis 760 Felt (cloth) 315 $125 $440 $Simonis 860HR Felt (worsted) 335 $125$460$
Pool table felt repair
Pool table felt repair is not a billiards service offered by many pool table manufacturers as it is quicker and less expensive to replace the felt. Felt repair can be tricky because you want to keep the fabric perfectly smooth and the damage may have gone deeper than just the felt. However,
You can buy some self-adhesive felt patches on Amazon for $7.95. They can cover the crack, but the balls might roll across it unevenly.
. They can cover the crack, but the balls might roll across it unevenly. If the hole is small enough, put a dot over it (even if it means the dot is in the wrong place).
If you’re dexterous with a needle and thread, use a curved needle to mend the tear. Then steam with a hot steam iron.
Custom pool table felt replacement
You can order a custom pool table felt bearing your artwork or company logo to add to your game room. Felt for a 7 foot or 8 foot table costs around $550 and for a 9 foot table around $600. Of course, the price varies depending on the quality, number of colors and size of the finished artwork.
Replace the felt on the coin operated pool table
The cost of replacing the felt on a coin-operated pool table is about the same as replacing the felt on a non-coin-operated table, averaging about $380 within a range of $295 to $595. It may have to be felted more often, since coin-operated billiard tables are usually in public places and are heavily used.
Felting of pool table bumpers
Refelting pool table bumpers costs $60 to $180 in addition to the price of refelting the table itself. When you reseam the table, you usually reseam the bumpers at the same time, since you’ve already disassembled everything.
back to top
Pool table recovering costs
Pool table restoration costs range from $195 to $695 depending on what needs to be fixed e.g.
Pool Table Replacement Cost Service Average Cost Service & Tuning $60 – $195 Relocation & Assembly $295 – $395 Refelting & Salvage $265 – $550 Shock Absorbers $60 – $180 Replacing Rails $280 – $450 Dismantling $195 – $245 Installation $240 – $360 Leveling 240 – $360 post processing $295 – $395
Restore pool table packages
During a standard pool table restoration, a professional will strip away the existing fabric, remove old glue or staples for a smooth playing surface, and smooth out any chips in the slate surface.
Pool Table Recovery Packages Package Average Cost Used Table Assembly $245 – $295 Used Table Assembly + Refelt $395 – $495 Refelt + Tune-up $280 – $400 Refelt + Tune-up + Rail Replacement $495 – $695 Move + Reassemble + Refelt $495 – $695
Replacing the pool table rail
Replacing the pool table rail costs $280 to $450. Replacing the rails must be done correctly or the balls will bounce off the rails at odd angles and make play difficult. Restoring the pool table rails is usually included in the price to re-felt the table.
Price examples for rails and accessories without assembly are:
Valley Pool Table Rails – $200 – $320, uncovered or covered
uncovered or covered precut rail blanks – $105 for 6 pieces in K55 profile
for 6 pieces in K55 Profile Rail Feather Strips $16 for one x wood 4′ length – ¼” x ¼”, $25 for 6
Replace pool table bumper
Replacing a pool table bumper costs $50 to $90. Padding trim is added to the ends of the rail rubbers and rail. On a good quality pool table, bumpers should last 10 to 20 years. Buy rail grommets for $44-$54 for six, pad trims for $5-$10 for a dozen, and bumper grommets for $12 for a dozen.
Cost to level a pool table
If your pool table has a problem and needs leveling, it’s $80 an hour to have a technician come to your home, with a $60-$95 service call out fee. Leveling a pool table is usually done at the time of setup or installation for $240-$360. Setup includes full assembly of your table, leveling and felting of the table.
Cost of refinishing a pool table
The cost of refinishing a pool table is $295-$395, including replacing the cloth on the top and rails. After that you will receive a comprehensive tuning to keep your pool table in top condition. Most companies do the following:
Disassemble the pool table Check and adjust the table height using the legs. Adjust the slate to level the surface. Reseal the slate seams. Install the new cloth. Assemble the pool table
Snooker Table Recovery Cost
The average cost of restoring a snooker table ranges from $373 to $520, depending on the quality of the felt.
12 foot snooker table Cost recovery Fabric quality Average cost Good $373 Better $500 Best $520
Pool tables and snooker tables look pretty much the same, with pockets in each of the four corners and a center pocket on each of the long sides. The bigger differences are in the sizes. Pool tables come in three different sizes of 7′, 8′ and 9′ along the longest side.
The 7-foot table is called a bar table,
The 8′ is referred to as the home table and
The 9′ table is a professional or tournament table.
In contrast, snooker tables are 12 feet long at their longest edge and are commonly found in the UK, while pool tables are more commonly found in the US, with the exception of British pubs.
back to top
Billiard table cost factors for re-felting
There are a few things that affect the cost of refelting your pool table, namely the type of cloth you choose and who you hire for it. As with anything, you can go easy and save money, or you can go all out and have a professional pool table.
The larger the table, the more felt is needed and the longer it takes to install. A professional pool table is 9 feet long, while most domestic slate pool tables are 7 feet or 8 feet long.
Cost of moving a pool table
The cost of moving a pool table will vary with the length of the move and the number of flights of stairs the pool table must be moved up or down. If the pool table moves it must be disassembled, therefore all prices include disassembly, reassembly and leveling.
Cost of Moving a Pool Table Service Average Cost to Move Pool Table Inside Home $295 – $395 Move Pool Table & Refelt $495 – $595
Assembly and disassembly of billiard tables
Move a pool table into your house: $295-$395. This price does not include new felt; You will reuse the old felt.
to This price does not include new felt; You will reuse the old felt. Move a pool table into your home and feel like this: $495-$595. This price includes all of the above plus new felt in the color of your choice.
This price includes all of the above plus new felt in the color of your choice. Disassemble, move, and reassemble: $395-$495. The pool table is disassembled and the individual parts are wrapped in durable moving blankets and labeled. The slate is stacked on a padded pallet. Everything is brought to the new home, reassembled and realigned. Does not include new felt.
The pool table is disassembled and the individual parts are wrapped in durable moving blankets and labeled. The slate is stacked on a padded pallet. Everything is brought to the new home, reassembled and realigned. Does not include new felt. Disassemble, move, reassemble, and re-felt: $595-$695. This price includes all of the above plus new felt in the color of your choice.
time and travel expenses
Generally, if you live within the city limits, having the technician drive to your home is free. As soon as you leave the service area, charges apply.
$25 for homes 10 miles away
for homes 10 miles away $50 for homes 20 miles away
for homes 20 miles away $75 for homes 30 miles away
certification and insurance
The company moving your pool table should be insured with a list of covered services on their website and invoices. A pool table weighs between 700 and 1,100 pounds and can cause significant damage to your home or a person if dropped. American billiard companies and installers can be certified by the leading manufacturer brands such as Brunswick and Diamond.
Installing pool tables can be complicated and the company should be experienced to get the best results. Moving your pool table is a very technical process and if a pool table mover damages your home or the felt on the table, you will have to let his/her company pay for the replacement and repair costs.
back to top
Pool tablecloth prices
Average pool tablecloth prices range from $130 to $335. Prices range from $97 for a 7-foot table with Teflon cloth to $1,190 for a 9-foot table with NCAA professional felt.
Pool Tablecloth Pricing Brand Cloth Type # Colors Size & Price Championship Invitational Cloth with Teflon 21 oz. felt
75% wool
25% Nylon 14 7′ – $97
8′ – $114
9′ – $139 Simonis 860 Cloth 27 oz. felt
90% wool
10% Nylon 9 7′ – $250
8′ – $310
9′ – $360 Simonis 860HR Worsted Fabric
70% wool
30% Nylon 2 7′ – $265
8′ – $330
9′ – $460 Wave7 NCAA Professional Grade Pool Table Felt Worsted
70% merino wool
30% Nylon 40 7′ – $899
8 minutes – $1,055
9 minutes – $1,190
wool cloth
Woolen fabric is the most common type of fabric for home pool tables and is often referred to as felt. It is a heavy fabric and contains 60% or more wool. It’s a heavy, thick cloth and the balls roll on it quite slowly.
worsted
Worsted is typically used in professional tournaments. This shawl has a distinctive weave and is made from the finest wool – merino wool. Worsted yarn costs much more than woolen fabric, and balls roll much faster on this cloth.
What Are the Different Types of Pool Felt?
Pool felt comes in two types – napped and worsted. There are many different brands of pool table felt, but each brand falls into one of two types.
Napped: This is the standard pool felt you get on home pool tables, bar pool tables, or coin-operated pool tables. It is inexpensive and the ideal cloth for a table. It has a nap, which means it has a sense of direction – if you run your hand over it, you’ll see the path your hand left. Because of this nap, the ball moves slower on this cloth.
This is the standard pool felt you get on home pool tables, pool tables in a bar, or coin operated pool tables. It is inexpensive and the ideal cloth for a table. It has a nap, which means it has a sense of direction – if you run your hand over it, you’ll see the path your hand left. Because of this nap, the ball moves slower on this cloth. Worsted: This is the cloth used by professional billiard players and is more expensive. So much more expensive that it’s out of reach for most home players, and bars won’t invest in it due to the heavy use of their tables. This is a flat weave fabric and since there is no nap, the ball moves faster.
Both types of pool table felt can be treated with Teflon, which is a good option for public gaming tables or homes with young children. The Teflon beads spills and prevents them from absorbing and soiling the cloth.
What is the best pool table felt?
The best pool table felt is worsted wool felt and is found on most professional tables and rarely on home game tables. Another name for it is “speed cloth” because the balls roll quickly on it.
Colors of the billiard tablecloth
back to top
frequently asked Questions
How long does it take to re-felt a pool table?
It takes a pro about 2 to 3 hours to re-felt a pool table. If you approach the pool table as a DIY project, it will take longer, maybe a day.
Can you move a pool table without refelting it?
You can’t move a pool table without removing the felt, but you can put the same felt back on if it’s in good condition. However, if you’ve been thinking about putting new felt on your pool table, now is a good time to do so.
How to clean pool table felt
The cloth on your pool table needs cleaning. It collects everyday dust and pollen, pet dander, and even the occasional spill. When you bought your pool table they probably gave you some instructions on how to clean the table and you may have a pool table brush to get the dirt and dust out of the crevices and corners.
How to clean pool table felt
Use the brush in straight lines (never in a circle) and then use a small plastic dustpan to sweep away the dirt. Never use a vacuum cleaner on your pool table. A vacuum can stretch the cloth and pull it out of line; This creates lines and creases that can deflect balls and ultimately ruin the game. If there are stains, use a damp white cotton cloth and blot the stain. Only use water, never soap. Soap can leave residue that attracts dirt and also deflects balls.
How much does new felt for a pool table cost?
Depending on the size of the table and the type of felt you purchase, most pool companies cost anywhere from $145 on the low end for a 7 foot table to up to $345 on the high end for a 9 foot table . You can also buy felt on Amazon. The price ranges from $65 on the low end and up to
$360 for Simonis 760 felt,
for Simonis 760 felt, $590 for 12′ Simonis 860 felt and
for 12′ Simonis 860 felt and $895 for a 9′ Custom Artscape felt with your logo centered on the table.
back to top
Pool table maintenance
Maintaining your pool table is necessary to keep your table in good condition so that you can play it for years.
Keep your table clean by brushing it regularly and cleaning up spills quickly.
Invest in a tablecloth to prevent dust, dirt and pet hair from settling on your table.
Keep chalk away from the cloth. Chalk dust is very fine and abrasive and not suitable for the fabric on your pool table.
Keep billiard balls clean with an occasional warm water/soap bath. You can also buy cleaners made specifically for billiard balls.
Make sure your pool table isn’t just in a window that allows for daily sunlight, which can potentially damage the wood and discolor the felt.
Do everything you can to ensure your family and friends keep drinks far off the table to protect them from condensation on the outside of a container and accidental spills.
Another point to bring up with anyone who may be playing at your table is that while leaning on the table for a moment to take a shot is part of the game, sitting on the table is can cause structural integrity issues over time.
back to top
DIY Refelt Pool Table or Hire a Service
Can you DIY and re-felt a pool table? It requires some tools and precision work, but you might enjoy it if you’re particularly good at spending a lot of time making sure things are perfect.
How hard is it to re-felt a pool table?
It’s about a 6 on a scale of 1-10. It’s more about being very precise than a difficult job. The pros have the right tools for leveling the pool table, while you may have to buy them. The most difficult part of re-felting the pool table will probably be stretching and applying the felt. It must be smooth with no creases.
How to refelt a pool table
Take off the rails. Underneath are screws/bolts that loosen them. Remove the old felt from the pool table surface. If the old felt has been glued in place, scrape off the old glue, making sure the surface is smooth and clean. Seal the seams with beeswax. Install the new felt by either gluing or basting. However you decide to attach the new felt, it will need to be stretched slightly to allow for a smooth surface. If it’s loose, it creates ridges and creases that impede the bullets’ path. Reattach the rails.
The description sounds simple, but the reality is that it’s quite a complex task. A professional needs 2 – 3 hours for this. So if you’ve never done it before, expect it to take all day.
Pool Table Felt Kits
A pool table felt kit can be purchased for $230 and includes everything you need to replace the cloth on your 7 foot pool table. For 8′ add about $25 and for 9′ add $45. The kit usually includes:
Rail cushion of your choice
Set of upholstery end panels
spray glue
contact rail cement
Cement for slate joints
stains
Matching color chalk
DVD with complete instructions on setting up and restoring the pool table
Get Free Estimates on HomeGuide from Trusted Pool Table Refelting Services:
Get Free Estimates
Is it hard to Refelt a pool table?
Replacing the felt, or more accurately the pool tablecloth, is often left to professionals, but the tools used are not expensive or complicated. The reason some consider it difficult is the exacting requirements of a pool table.
How to Replace Pool Table Cushions in 1 Hour
License: Creative Commons<\/a>
<\/p>
<\/p><\/div>“} 1 Use a special spray adhesive if the table can’t be stapled. If your table doesn’t have a wood or chipboard backing under the slate surface, you’ll need to find a special glue to glue instead Felt onto the slate.If you see this backing, follow the instructions for basting the felt instead.3M Super 77 Multipurpose Adhesive is a popular option.If your table doesn’t have a wood or chipboard backing under the slate surface, you may need a special one instead Find glue to glue the felt to the slate, if you see this reverse side, follow the directions for basting the felt instead.
{“smallUrl”:”https:\/\/www.wikihow.com\/images\/thumb\/0\/03\/Felt-a-Billiard-Table-Step-15-Version-2.jpg\/ v4- 460px-Felt-a-Billiard-Table-Step-15-Version-2.jpg”,”bigUrl”:”\/images\/thumb\/0\/03\/Felt-a-Billiard-Table- Step-15-Version- 2.jpg\/aid1405541-v4-728px-felt-a-pool-table-Step-15-Version-2.jpg”,”smallWidth”:460,”smallHeight”:345,”bigWidth”:728,”bigHeight”: 546,”licensing”:”
License: Creative Commons<\/a>
<\/p>
<\/p><\/div>“} 2 Cover the sides of the table with newspaper. Protect the edges of the table from spilled glue with a layer of newspaper extending over the edge. Remove the newspaper from each edge , just before you lower the glued felt.
{“smallUrl”:”https:\/\/www.wikihow.com\/images\/thumb\/7\/7f\/Felt-a-Billiard-Table-Step-16-Version-2.jpg\/ v4- 460px-Felt-a-Billiard-Table-Step-16-Version-2.jpg”,”bigUrl”:”\/images\/thumb\/7\/7f\/Felt-a-Billiard-Table- Step-16-Version- 2.jpg\/aid1405541-v4-728px-felt-a-pool-table-Step-16-Version-2.jpg”,”smallWidth”:460,”smallHeight”:345,”bigWidth”:728,”bigHeight”: 546,”licensing”:”
License: Creative Commons<\/a>
<\/p>
<\/p><\/div>“} 3 Cut the felt according to the manufacturer’s instructions. Felt usually comes in large pieces, along with instructions for cutting strips for each railing. Follow these instructions to ensure that you end up getting pieces of the right size.
{“smallUrl”:”https:\/\/www.wikihow.com\/images\/thumb\/5\/5f\/Felt-a-Billiard-Table-Step-17-Version-2.jpg\/ v4- 460px-Felt-a-Billiard-Table-Step-17-Version-2.jpg”,”bigUrl”:”\/images\/thumb\/5\/5f\/Felt-a-Billiard-Table- Step-17-Version- 2.jpg\/aid1405541-v4-728px-felt-a-pool-table-Step-17-Version-2.jpg”,”smallWidth”:460,”smallHeight”:345,”bigWidth”:728,”bigHeight”: 546,”licensing”:”
License: Creative Commons<\/a>
<\/p>
<\/p><\/div>“} 4 Identify the playing surface and place the felt on the table. If the surface isn’t labeled “up,” try to identify it by feel, or face up to a professional.Your Felt Game’s surface may be smooth or have a “nipping” in one direction depending on the type;You may need to ask an expert to identify face up if you are unfamiliar with the material.Place the Felt across the table Make sure any overhang is as parallel to the edge of the table as possible.
{“smallUrl”:”https:\/\/www.wikihow.com\/images\/thumb\/2\/22\/Felt-a-Pool-Table-Step-18-Version-2.jpg\/ v4- 460px-Felt-a-Billiard-Table-Step-18-Version-2.jpg”,”bigUrl”:”\/images\/thumb\/2\/22\/Felt-a-Billiard-Table- Step-18-Version- 2.jpg\/aid1405541-v4-728px-felt-a-pool-table-Step-18-Version-2.jpg”,”smallWidth”:460,”smallHeight”:345,”bigWidth”:728,”bigHeight”: 546,”licensing”:”
License: Creative Commons<\/a>
<\/p>
<\/p><\/div>“} 5 Fold the top end of the felt up and apply glue. Fold the top end of the felt onto the table, exposing the underside that extends over the vertical side of the slate Spray this part of the underside vigorously with the adhesive and also spray the slate where it is to be attached and leave until tacky according to the adhesive manufacturer’s instructions.
{“smallUrl”:”https:\/\/www.wikihow.com\/images\/thumb\/a\/ab\/Felt-a-Billiard-Table-Step-19-Version-2.jpg\/ v4- 460px-Felt-a-Billiard-Table-Step-19-Version-2.jpg”,”bigUrl”:”\/images\/thumb\/a\/ab\/Felt-a-Billiard-Table- Step-19-Version- 2.jpg\/aid1405541-v4-728px-felt-a-pool-table-Step-19-Version-2.jpg”,”smallWidth”:460,”smallHeight”:345,”bigWidth”:728,”bigHeight”: 546,”licensing”:”
License: Creative Commons<\/a>
<\/p>
<\/p><\/div>“} 6 Carefully attach the felt to the table. Starting at one end, carefully align the glued felt with the slate, press down, then move along of the glued end and pull tight while attaching it to the table. You may need an assistant to ensure the material is taut, especially at the beginning of the process. The felt should be firm enough to avoid any wrinkles , but an ultra-firm surface is not required unless you wish to practice for professional tournaments.Most importantly, pull the felt with equal pressure during this installation.Start at one end, line up the glued felt carefully with the slate, press down, then move along the glued end and tighten as you attach. You may need an assistant to make sure en that the material is taut, especially at the beginning of the process.
{“smallUrl”:”https:\/\/www.wikihow.com\/images\/thumb\/a\/ad\/Felt-a-Billiard-Table-Step-20-Version-2.jpg\/ v4- 460px-Felt-a-Billiard-Table-Step-20-Version-2.jpg”,”bigUrl”:”\/images\/thumb\/a\/ad\/Felt-a-Billiard-Table- Step-20-Version- 2.jpg\/aid1405541-v4-728px-felt-a-pool-table-Step-20-Version-2.jpg”,”smallWidth”:460,”smallHeight”:345,”bigWidth”:728,”bigHeight”: 546,”licensing”:”
License: Creative Commons<\/a>
<\/p>
<\/p><\/div>“} 7 Repeat the process with the back end and long sides. The gluing process is identical for each of the remaining three sides. Wait at least a few minutes or whatever between each side long The adhesive manufacturer recommends creating a strong initial tack Gently pull each side taut before applying adhesive, making sure there are no wrinkles in the cloth and you pull with equal force on each side.
{“smallUrl”:”https:\/\/www.wikihow.com\/images\/thumb\/a\/a9\/Felt-a-Billiard-Table-Step-21-Version-2.jpg\/ v4- 460px-Felt-a-Billiard-Table-Step-21-Version-2.jpg”,”bigUrl”:”\/images\/thumb\/a\/a9\/Felt-a-Billiard-Table- Step-21-Version- 2.jpg\/aid1405541-v4-728px-felt-a-pool-table-Step-21-Version-2.jpg”,”smallWidth”:460,”smallHeight”:345,”bigWidth”:728,”bigHeight”: 546,”licensing”:”
License: Creative Commons<\/a>
<\/p>
<\/p><\/div>“} 8 Cut the felt and use the excess to line the pockets. Cut the excess felt overhang on each side. Cut a 2.5 cm wide one on one side Strip off Cut the material stretched across the pockets, then cut this strip into smaller pieces and tape them over the vertical, circular surface of the slate to protect it from the billiard balls.
advertisement
How do you know if a pool table cushion is bad?
If the cushions need to be replaced, you may also hear the sound of impact when the balls hit the rail. Instead of springing off the cushion and back towards the center of the table, the balls will roll in unexpected directions or virtually stop rotating. These are all signs that the cushions need to be replaced.
How to Replace Pool Table Cushions in 1 Hour
Find out how to tell when it’s time to replace your pool table cushions and what to do about it.
How do I know if pool table cushions need replacing?
It’s a common misconception that cushions that are rarely played on can’t be bad. However, it’s a little-known fact that rubber needs to flex to maintain its natural spring, so a table that’s been used very little will most likely need the cushions replaced.
Rubber pool table covers age naturally. As the rubber ages, it will start to negatively affect the game.
As you play, you may find that the billiard balls don’t bounce off the rails like they did when the table was new. If the cushions need to be replaced, you may also hear the impact sound as the balls hit the track. Instead of bouncing off the cushion and back towards the center of the table, the balls roll in unexpected directions or practically stop spinning. All of these are signs that the pillows need replacing.
Billiards Congress of America (BCA) pool cushion test
According to BCA specifications: “Pads should respond to conform to the three cushion angles prescribed in the “diamond” (or site) system shown below, up to ±1 ball width under controlled conditions. The speed of the table cushions should be such that when placing a ball on the head spot, when shooting through the foot spot, with midball English, with a horizontal cue and a solid shot, the ball must travel at least 4 to 4 ½ lengths from the table, without jumping.”
You can also visually inspect the pillows and look for any indentations or slants, a bad pillow can warp.
Another cause of poor rebounds is loose pool table rail bolts. Failure to securely mount the rails can also result in poor play.
How long do pool table cushions last?
It’s difficult to say. The lifespan of billiard tables and their components depends heavily on the environmental conditions. For example, pool tables in sunny rooms have a different lifespan than pool tables in basements. Rooms with direct sunlight can accelerate the aging process of rubber as it gets hotter and drier. Basements do not accelerate the aging process because it is a cool, humid environment. In general, standard quality pillows can lose their bounce in 12-15 years. Higher quality pillows like Olhausen’s Accu-Fast pillows are said to last over 25 years.
Find out more about Monarch’s billiards services. We can replace the cushions on custom and antique pool, carom and snooker tables.
We provide quality care for your pool table
If your cushions are damaged or worn out, we can help bring your pool table back to life.
Monarch Billiards is a family owned business that has been based and counting in the Philadelphia area for 71 years. We supply and service all types of pool tables and accessories. We also create unique, custom tables upon request. For expert advice or assistance, call Monarch at 610-595-4651 or contact us online.
How long will a pool table last?
Generally, 20-25 years, although some cushion rubber lasts longer. If the pool table has seen direct sunlight, cushion life will be greatly reduced. We have also seen pool tables less than five years old that have “dead” cushions. It is unusual but it happens.
How to Replace Pool Table Cushions in 1 Hour
Check out our guide: How to move a pool table
How long do billiard balls last?
No abrasion or flat spots on the ball that accumulate dirt and wear the cloth ! Easily maintained with the Aramith ball cleaner, the Aramith balls will last up to five times longer than any other ball (UP TO 40 YEARS in case of home use).
How to Replace Pool Table Cushions in 1 Hour
Manufactured by Saluc in Belgium, Aramith Excellence is the result of a high-tech process that combines the unsurpassed properties of Aramith resin with fine Belgian craftsmanship.
Their consistently reliable performance guarantees players the pleasure of razor-sharp precision. Their exceptionally long product life offers table owners the lowest annual ball costs. Thus, for nearly half a century, Aramith earned its legendary reputation as a hallmark of true and unparalleled quality.
How do I update my pool table?
- Step 1: let your wood dry. …
- Step 2: disassemble the table. …
- step 3: update the railings. …
- Step 4: make trim boards. …
- Step 5:prep for paint. …
- Step 6: paint. …
- Step 7: final touches for the railings. …
- Step 8: Liquid Nails.
How to Replace Pool Table Cushions in 1 Hour
Growing up we had an old pool table that we got off a craigslist for quite a deal. When my mom moved to North Carolina, she didn’t have room for the pool table in her new home, so she kindly gave it to Andrew and me as gifts.
We were thrilled to get such a nice pool table for free, but…it didn’t match the style of our game room. The classic style and red felt would stick out like a thumb in the modern blue playroom.
So what did we choose? renovate it! Painting, refelting and replacing the legs would certainly be more cost effective than getting a new slate pool table. So we dived in (without really having a plan) and created something better than we both thought possible!
The ONLY tools you need to DIY Want to build magazine-worthy furniture and decor? The Essential Tools Roadmap shows you what tools you actually need to complete 95% of DIY furniture and home improvement projects (not as many as you think!). GET YOUR FREE ROADMAP HERE
Let’s start crafting!
This post contains affiliate links for your convenience (meaning if you make a purchase after clicking a link, I’ll earn a small commission, but it won’t cost you a penny more)!
Tool
What you need 120+ grit sandpaper
wooden spatula or putty
1.25″ metal (depending on the pool table size – enough for corners of the base and all railings)
18mm googly eyes (yes, you heard that right)
craft glue
1.25″ siding board (depending on the pool table size – enough to go around the underside of the base)
Quart Chalk Paint (Grey Screen by Sherwin Williams)
spray paint
wax
razor blade scraper
felt
Leveling Feet (4)
Vinyl (we used chalkboard vinyl for added texture)
4x6x8 pine
4x4x6 pine
This is how you give your pool table a modern update
Do you wish you could build magazine-worthy furniture and decor without a workshop full of expensive tools? Get the Essential Tools Roadmap and find out which tools are essential for DIY and which 3 tools you should start with.
Step 1: Let your wood dry
Get your 4x6x8 and 4x4x8 boards at your local hardware store. Please note that they require a certain drying time. We are happy to collect our wood 2 weeks before it is intended to be used (technically you should allow it to dry even longer).
Step 2: Disassemble the table
We were lucky that ours came in pieces, but if yours is already assembled start by unclipping the bumpers, removing the felt and slate and taking the legs off.
Carefully remove the bottom bar from the base of the pool table. Our pool table had minor water damage so part of the pool table base came loose when we removed the molding. Luckily it will be covered so you don’t have to worry about fixing the texture.
Detach the apron from your railing. Remove the felt from your railing by using pliers to remove any staples. Some might come out if you pull on the felt. However, when removing the staples, be sure to remove them all.
If one of your railings has a logo plaque, unscrew the plaque and cover with putty to smooth the surface. The logo is partially obscured by the metal detail that runs around the railings, so it’s best to remove it entirely for a finished look.
Step 3: Update the Railings
Cut off the excess wood from the railings. On each of our railings was a slot for attaching the apron. Approach this slot when cutting, but be sure to leave it intact so the skirt can still slide in.
Using a hacksaw, cut your metal pieces to the size of your railing. Measure the depth of your pool table from the bottom of the corner pocket to the bottom of the base and cut 4 pieces of metal to place at the corners of the pool table base.
Step 4: Make trims
Cut your trim board to fit between the metal corners. You can mimic it by placing (or clamping) your metal corners and measuring the distance. As you mock up the trim strips, mark them across the entire strip of metal to get the correct angle to cut.
Glue googly eyes to your trim boards about 3″ apart. To speed up the process, use a ruler to get the spacing on one of the boards. Then, using that board as a guide, place the googly eyes on your other boards in line with the googly eyes on your first board.
Step 5: Prep for Paint
Wipe down your pool table base, skirts and railing to remove any residue and prepare them for painting. We chose chalk paint because you don’t need to sand down your surfaces before applying.
To prepare 4×6 and 4×4 for painting, fill in any cracks and knots with putty. We used putty because it doesn’t shrink, but wood putty will work too. Just be sure to fill in your cracks and knots when using wood spatula. Then sand with 120 grit sandpaper and work your way up to 220 grit sandpaper for a smoother finish. Yes, chalk paint doesn’t need to be sanded before application, but you should sand this wood as treated wood is generally very rough and has a handful of splinters when you buy it from the store.
Step 6: Paint
Apply 2-3 coats of chalk paint to the base, skirts and railing of your pool table.
Spray paint your metal parts, pockets, triangles, and trim.
Step 7: Finishing touches for the railings
While the paint dries, cut out the dots for your pool table railing. I cut them out of chalkboard vinyl with my Cricut. You can use regular vinyl but I wanted the added texture of the chalkboard vinyl.
Place the dots on your pool table railing. You can use rulers and be precise, or you can try my method – I used my finger as a spacer from the felt area and then aligned it with my eyes to the old point.
Step 8: Liquid Nails
Use liquid nails to attach the metal pieces to your railings. Clamp each side while the glue dries.
Nail the metal pieces to the corners of the pool table with liquid. Use staples to secure while drying.
Then use liquid nails and 1.5 inch real nails to attach the trims.
Step 9: Legs
Screw leveling feet to the bottom of each leg.
Attach the legs using the screws from your original legs. Pre-drill for the screws with a slightly smaller drill bit than your screw.
Turn the pool table over and place it in the room where you want it.
Measure the distance between your legs and trim your 4×6 to size. Drill six pocket holes (3 on each side) on the bottom of the 4×6. Screw the 4×6 to your legs at the desired height. Place a spirit level on the 4×4 to ensure it stays level.
Level the pool table with the leveling feet.
STEP 10: Add the slate
Place the slate on the pool table and pray your legs will hold up! (just kidding – they are very strong). Position the panel so that it aligns.
Check that the pool table is level again. If this is not the case, you can use a jack to raise one side of the pool table to access the leveling feet. Once you’re leveled, you need to make sure that all of the slate pieces are aligned with each other both laterally and vertically. We use a cut up aluminum can as a washer to align the parts.
After aligning, screw in the slate.
Step 11: Preparation for Felting
If you have deep chips in your slate, fill them with Bondo by following the directions on the bottle.
Use wax to fill in the cracks between the slate pieces. We’ve found it’s easiest to place the wax along the cracks and then melt it with a blowtorch. Note: Be safe! Always practice fire safety and keep a fire extinguisher nearby, just in case.
Scrape off excess wax with a razor blade scraper. Check your seams for gaps in the wax and repeat the melting and scraping process as many times as necessary to completely smooth out the seams.
Step 12: Felt the Table
We’re getting closer now! It’s time to felt the pool table. We’ll have a full Felting post next week, so stay tuned! When you can’t wait – Google is awesome ?
Step 13: Assemble
Cut holes in the felt where you will screw the railings.
Once everything is felted, it’s time to reassemble the pool table. Start by assembling one half of the railings (3 total) and the pockets. Assemble them upside down. Screw in a couple of screws without the washers on each railing to help position the railings when you flip them over.
Turn the assembled rails over and line them up with the slate. Work your way around the pool table with bolts and washers by screwing down the railings. Be sure to remove any screws you added in the previous step and screw them back in with washers. Repeat with the other side.
Step 14: Finishing Touches
If you want to go the extra mile you can caulk between the legs and the 4×4 bar and then brush over it. You can also fill and paint the nail holes on the trim boards.
We’ve made it to the most important step – line up the balls and start playing pool! That was a big change, so plan a party, celebrate and show off that pool table!
We’ve received some funny replies about this pool table makeover on Instagram (@craftedbythehunts), but the most common one is that nobody thought of renovating a pool table! It’s like another piece of furniture you might have lying around. There is always a way to update it and give it a second life.
Are you ready to tackle yours? Send us your pictures and questions on Instagram. We’d love to see your transformation and cheer for you!
What is under the felt on a pool table?
Cushion. The cushion is the felt covered rubber interior of the rails on the pool table. For example, you may hear that balls must be driven off the cushions on a break. Cushion is often used interchangeably with the term “rail” or “bank”.
How to Replace Pool Table Cushions in 1 Hour
An overview of billiard table parts and layout
In many of our posts on how to play popular pool games – including 8-Ball, 9-Ball, Cutthroat Pool and other fun pool games – we mention different parts of the table to explain the basic rules of each game.
So, in order to understand the rules, you should at least know what these terms mean.
Luckily, the anatomy of the pool table is fairly easy to understand.
But to make it even easier for you, we’ve prepared a basic overview of pool table anatomy, including where things are on the table and what they mean.
Now, when someone says something like “put your hands on the ball behind the headline,” at least you know what they’re talking about.
This one small billiard cue accessory will change your game. If you can only afford one tool to maintain the tip of your cue, then the Cuetec Bowtie Tip Tool is it: 3-in-1 tool to help your tip hold the chalk better. Avoid mistakes. Small enough to fit in your pocket.
Pool Table Anatomy 101
Parts of the pool table defined
apex of the triangle
This is the top of the rack. In some games you need to place a specific ball on top (e.g. the 1 ball in a 9 ball game) and line it up with the foot spot.
middle string
The center cord runs between the two side pockets and intersects the midpoint (dead center of the pool table). This is an imaginary line used as a reference point.
corner pockets
There are four corner pockets on a pool table. Become familiar with these as you begin to designate your shots (e.g., 5-ball, right corner).
The opening of a corner pocket (aka “mouth”) should be a minimum of 4 ⅞ inches and a maximum of 5 ⅛ inches. The entry angle of a corner pocket is 142° (± 1°).
pillow
The cushion is the felt covered rubber inside of the rails on the pool table. For example, you can hear that balls have to be driven off the boards during a break. Cushion is often used interchangeably with the terms “rail” or “bench”.
Diamonds (aka Landmarks)
The diamonds on the table rails serve as references or target points. These inlaid marks are spaced along the short rails (ends of the table) in one-fourth increments and along the long rails (side rails) in one-eighth increments.
For advanced players, the diamonds are used to benefit from the “diamond system”; a mathematical approach to planning multi-bank shots.
The rest of us use the diamonds to help us aim and understand where the head and foot lines are.
foot of the table
This is the end of the table where the balls are placed. They break from the top of the table to the bottom of the table.
base
The foot point is the point at the foot end of the table between the second diamonds on the long rail. It also aligns with the center diamond on the short rail.
This is the “rack end” of the table where you “spot the ball” and where you should place the top object ball when playing an 8-ball or 9-ball game.
The “foot point” is commonly mentioned in the rules and instructions for most billiard games. Now you know exactly where it is!
foot cord
The foot cord is an imaginary line between the second diamonds on the long rail at the foot of the table. It goes through the base. This is mainly used as a reference point for positioning and understanding the layout on a table.
head of the table
This is the end of the table that the shooter breaks away from. This is where the billiard table manufacturer usually puts his type plate.
head point
Opposite the foot patch is the head patch. At this point, the imaginary line of the head string intersects between the second diamond on the long rail and the middle diamond on the short rail.
head cord
The Head Strong is an imaginary line that runs at the head of the table between the second diamonds on the long rail.
The area behind the head string is where you break off and where you need to place the cue ball after a scratch in an 8-ball game, for example.
You will often see that in a game like 8-Ball, the cue ball must be “held in hand behind the head string.” It just means you can place the cue anywhere behind the second diamonds on the long rail.
If your table doesn’t have diamonds or visors, now you know that the head cord is behind the “head point” to make things easier.
playing area
The playing surface is the flat, level (hopefully) felt-covered surface on which you play billiards. The playing surface of a higher quality table consists of slate. These tables usually need to be properly installed and leveled by professionals.
Lighter and less expensive pool tables use an MDF playing surface. These don’t last as long and tend to warp, but are often good budget-friendly options.
The playing surface for a full size table should measure 50″ x 100″.
side pockets
There are two side pockets positioned in the middle of the table. The openings should be between 5 ⅜ and 5 ⅝ inches wide. The angle at a side pocket entrance is 103° (± 2°).
There you have it. A basic overview of parts of the pool table.
Understanding the anatomy of billiard tables will make it easier for you to learn how to play new games and how to hit challenging shots.
Then it’s time to tackle your next challenge: learning how to play billiards.
What are pool table cushions made from?
The cushion rails themselves were generally made of the same timber as the Billiard Table under-framing, that is from Mahogany, or Oak, or Walnut.
How to Replace Pool Table Cushions in 1 Hour
POOL TABLE CUSHION
Compared to the game’s ancient origins that we’ve already heard about, rubber pool cushions are a fairly recent introduction.
In the early 19th century and before, all billiard table cushions were made of “cunning” – in other words, the cushions were filled with layers of felt and similar materials that provided something of a soft cushion from which the balls would rebound a short distance . However, by modern standards, “cunning” pillows clearly had nothing to recommend. We would certainly describe them as “extremely slow”.
The picture shows a section of a ‘List’ billiard table cushion
In 1835, John Thurston, who had introduced slate beds the previous year, now introduced India Rubber Cushions. The original rubber padding was made from pure natural rubber. This might not have been the full improvement you are imagining. Pure natural rubber cushions were reasonably satisfactory in warm weather conditions, although they were actually a vast improvement over the “cunning” cushions, but in cold winter weather the rubber became extremely hard – so hard you might as well have had a fitted wooden pad nose instead of rubber.
Image of the January 1936 page of The Billiard Player magazine
However, when the cushions were heated, the natural rubber regained its elasticity, and so long metal pans corresponding to the nose of the rubber cushion were placed around the pool table and filled with hot water and placed around the pool table two or three hours before the game started. I have a copy of one of these hot water pans with me for viewing.
“Hot water bottle” for early rubber billiard cushions
Also, during my own early years in the billiards trade, we frequently brought in cushion rails to be “rebuilt with new rubber” and when the cushions were stripped off we found that they were still fitted with pure natural rubber which was literally as hard as wood . and I have a few small samples here for testing.
Back in the days I just referred to, we salvaged the natural rubber and dissolved it in naphtha to make our own rubber putty solution, which was then used to fit the new rubber into the wooden support blocks.
My father (Norman) always told me how, in his own young days in the billiards trade, he and other traveling billiards fitters were frequently sent to the larger private houses when the owners intended to invite their friends over for a game of billiards, to take the cushion rails off and before the Fire to warm to soften the natural rubber cushions.
Later, when the process known as “vulcanizing rubber” was discovered or invented, it prevented the rubber from becoming extremely hard at low temperatures. Thus, John Thurston again introduced the first cushions made of vulcanized rubber, which were generally described as “frostproof”. They were indeed hand built with great skill using layers of vulcanized rubber about 1/8 inch thick.
Image of an early rubber pad made from rubber strips
During this time, the shape of the pillow nose was heavily rounded – a shape we refer to as a “bull nose”. The cushion was so high that when the ball came to rest on the cushion it was almost impossible to hit the ball as only a small fraction of its surface area was above the top of the cushion.
Thus, the shape of the face of the pad nose underwent many modifications, reducing the height of the pads, making it much easier to hit the ball. Therefore, for many years, the lower type of pillow, which used vulcanized rubber, was described as a “low frost resistant pillow”.
I have also provided you with a clip or two showing you hand built rubber pads and up until the start of WWII in 1939 it was always accepted that “built rubbers” were superior, although molded rubbers had been on the market for a number of years. Since the war, molded cushioning gums have completely supplanted built-up gums, partly I think because the very skilled staff who used to build up the gums left the trade during the years of gum shortages and the trade was once again confronted with the economic realities of life that the time and expense of manually building up rubbers at post-war wages would have made the price of billiard cushion rubbers quite prohibitive.
So far I’ve really only talked about the actual upholstery nose. The cushion rails themselves were generally made of the same wood as the billiard table base, i.e. mahogany, oak or walnut.
However, it was recognized that to a certain extent, the heavier the pad rail, the better the foundation it provided on which to mount the pad nose – a good foundation made for a faster and quieter pad, hence the various billiard tables that led -Marker different mods to try and get best possible results.
The most notable and successful was undoubtedly the “Steel Block” cushion introduced by Burroughes and Watts. This company is now part of Riley Burwat Limited. Thousands of billiard tables are fitted with Burroughes and Watts steel block cushions, which consist of a steel plate approximately ¼ inch thick that runs the full length of the cushion and the full depth of the cushion body on which the wood cushion blocks and billiard cushion rubber rests This plate becomes solid bolted to the edge of the slate bed and then covered with a wooden slat so the table looks indistinguishable from other tables with plain wood upholstery slats (actually it was W. Buttery, an employee of Burroughes & Watts, who patented the steel block cushion in 1836. Riley Burwat Ltd reverted to the Riley name and ceased trading in 2002/3.
Steel block billiard cushion patent 1886
Another attempt at making a heavier and stronger foundation was made by Thurston’s who actually fitted a slab of slate into the front of the cushion rails, the full length and depth of the cushions and some are still in place. (Thurston named his cushion the “Adamant” cushion, a set of which is attached to the cast-iron table in the collection.)
Section of a Thurston ‘Adament’ cushion with slate insert
However, I think it’s perfectly fair to say that a good sound pad rail made from a heavy mahogany oak or walnut will do just as well and have many advantages when the table is being serviced as they are quicker and easier to work with – an important feature in times of high labor costs.
© Norman Clare 1990. © E.A. Clare & Son Ltd 2018
Reproduction of this article is prohibited without permission from E.A. permitted. Clare & Son Ltd
www.thurston.co.uk
to contact us by phone
0151 482 2700
or
Email – [email protected]
Copyright E.A. Clare & Son Ltd 2009 & 2011
Go to top of page
How often should you Refelt a pool table?
Generally, if you play pool daily, you can expect the felt to last 3-5 years. If you don’t play on a daily (or near-daily) basis, your felt could last twice as long. In this article, we will go over what you can do to extend the life of your felt and how to know when it is time to replace it.
How to Replace Pool Table Cushions in 1 Hour
How long does pool table felt last? How long the felt will last on your pool table depends on how often you play pool and how well you take care of the felt. In general, if you play billiards on a daily basis, you can expect the felt to last 3-5 years.
If you don’t play daily (or almost daily), your felt can last twice as long. In this article, we’ll go over what you can do to extend the life of your felt and how to know when it’s time to replace it.
How to extend the life of pool table felt
If your pool table gets a lot of use, that’s fantastic. It means you’re getting your money’s worth off the table. However, it also means that your felt will wear out faster. The interaction between the felt, balls, and chalk on a pool table eventually causes the felt to wear out.
Even if you play daily, you can breathe more life into your felt by taking good care of it. We’ve put together this list of best practices to help you keep your felt in good condition for longer.
Use a pool table cover when the table is not in use.
Brush the table regularly to keep it clean.
Consider using a vacuum with an upholstery brush to remove chalk from the table.
Do not allow any drinks or food on or near the table.
Don’t take scoop shots.
Do not allow pets on the table.
Don’t chalk across the table.
Keep your billiard balls clean.
Wipe the rails. Dirt on the rails can get onto the bed.
Remember that sunlight will fade the felt.
If you follow these guidelines, your pool felt will surely last longer than if you didn’t. On the other hand, most people want to change their felt color long before the felt wears out. If you like to change up your decor often, special care may not be as important to you.
We have some very helpful posts if you are looking to remove a stain from your pool table or remove the chalk.
When to change your pool table felt
Because felt wear is largely dependent on how often you use your pool table, it’s not easy to remember your next felt change. You need to keep an eye on your felt.
Signs your felt needs changing:
It looks like it needs to be replaced. If the felt looks like it needs replacing, it most certainly does.
It feels bristly.
It has become corrupted.
It bulges when you push in with your hand.
It shows any signs of looseness.
If your pool table felt is showing any of these signs, whether you like it or not, it’s time to have it replaced.
How much does it cost to replace pool table felt?
Replacing the felt on a pool table will definitely cost hundreds of dollars. Most replacements cost between $300 and $500 depending on the size of the table and the quality of the felt.
You can save some money by buying a piece of felt from Pooldawg and re-felting the table yourself, but it’s not recommended. Even a small mistake can result in an annoyingly imperfect playing surface. But if you’re familiar with DIY methods and have thoroughly researched the process, it’s possible and will save you a few hundred dollars.
How to Replace Your Pool Table Cushion Rubber
See some more details on the topic pool table cushion replacement here:
Cushions – Pool Table Repairs – Billiard Shop
Billiard Shop’s pool table cushion replacement process includes the following steps: Removing cushion rails from the table and transporting them to one of our …
Source: billiardshop.com.au
Date Published: 1/11/2022
View: 9403
Pool Table Cushion Replacement – Pool Felt
Installation Gue Overview When consering cushion replacement first make sure your rails are mounted tight to the table. If they are loose they may play …
Source: poolfelt.com
Date Published: 2/20/2021
View: 7242
How to Replace Pool Table Cushions – Basic Advice from …
So when do you replace the cushions of your pool table? The cushions recommend replacing every 10 years. Many manufacturers go to offering a …
Source: crazebuzz.com
Date Published: 12/12/2022
View: 6220
Is it Time to Replace Your Pool Table Cushions?
How Do I Know If Pool Table Cushions Need Replacing? · Billiards Congress of America (BCA) Pool Cushion Test · How Long Do Pool Table Cushions …
Source: www.monarchbilliards.com
Date Published: 12/11/2022
View: 7339
How Much Does It Cost to Replace Pool Table Felt?
Highlights It costs an average of $300 to re-felt a pool table, with a typical price range of $250 to $300.
You can pay as little as $150 or as much as $500.
Pool tables come in three sizes, and size affects price.
The cost of refelting billiard tables is split fairly evenly between materials and labor.
You can reduce the cost of refelting billiard tables by choosing a less expensive material.
A smooth surface on your pool table is so important for a game night. But if you regularly host pool tournaments in your basement, this pool table felt can become worn and damaged.
On average, it will cost you $300 to re-felt a pool table, although the price can be less or more depending on the size of the table. The typical range is $250-$350, but it can cost as little as $150 or $500.
Related Article 6 Things You Should Do Before Buying A Pool Table These expert tips will have you up and running in no time
Average cost of replacing pool table felt
Average cost low end high end $300 $150 $500
How much does it cost to refold a pool table by type?
The larger the pool table, the more it costs to replace the felt. Pool tables usually come in three sizes: 7 feet long, 8 feet long, and 9 feet long. Here are some average costs you can expect:
Type Cost 7 foot pool table $150-400 8 foot pool table $200-450 9 foot pool table $250-500
Billiard Table Refelting Cost Breakdown
In general, the breakdown of costs for a pool wrap is relatively simple. There are only two factors: the cost of the felt itself and the labor cost of installation.
materials
Pool felt generally accounts for about half of the project cost. So for an 8 foot pool table you would spend between $100 and $250 on the felt.
work
Work makes up the other half. You will pay anywhere from $100 to $250 for an 8 foot pool table to have a professional install it.
size
Of course, material and labor costs will go up or down as you increase or decrease the pool table size. Obviously if you have a different size pool table it would require more or less felt and more or less labor to install it.
Cost to refold a pool table yourself
Photo: sandsun/Adobe Stock
If you re-felt a pool table yourself, you only have to pay for the felt. That means the cost of refelting is cut in half and you’ll likely only pay $100-$250 to get the job done.
However, trying to make this project yourself is not the best idea. Felting a pool table requires specialized training, so attempting to do it yourself will not yield the desired results.
After all, it’s not just about laying out carpets: the surface of the billiard table has to be perfect in order to be able to play billiards properly. Instead, contact a pool table professional in your area for a quote.
Tips for reducing the cost of re-felting a pool table
Aside from doing the work yourself, there are a few ways you can reduce the cost of your pool table re-felting bill.
1. Get multiple quotes
The first, and possibly best, option is to simply not accept the first offer you receive from a pool table company. Chances are there are several pool table companies in your area, so give a few of them a call and get some quotes.
Considering the only information they need is the size of your pool table and the type of felt you want, they should be able to tell you how much they are asking of their head. Therefore, it is much easier to get multiple quotes for this project than it is for more complicated home projects.
2. Choose a lower quality felt
There are actually two types of felt: napped and worsted. Shabby fabric is the standard material for felt on billiard tables. It’s a less expensive type of material that requires more brushing and maintenance, and may play a little slower.
Worsted, on the other hand, is a flatter fabric that allows the ball to move a little faster and last longer. As a result, it is more expensive. To save money, opt for naps (although it may cost you more in the long run since it requires more maintenance and you’ll have to replace it sooner).
Related Article 23 Playroom Ideas for Action-Packed Fun Warning: Your house can become a popular neighborhood hangout
Questions and answers about refelting billiard tables
Is it hard to re-felt a pool table?
Yes, it is difficult to re-felt a pool table as you need exact measurements and a precise fit. Unlike installing carpet, where fitting is only important for aesthetic reasons, accurate fitting is required on a pool table or you will not be able to play pool properly.
Can you paint pool table felt?
Yes, you can dye pool table felt a different color. Along with green, red is a common color. The best way to do this is to dip a sponge into the paint and gently rub the paint over the fabric.
How do you get paint off a pool table felt?
You can remove small stains on felt by dabbing the area with a soft cloth and picking up as much paint as possible. Then use a mixture of water and detergent to further blot the area. Then dab with clean water to rinse.
Pool Table Cushion Life Expectancy and Test
Playing a good game of pool, whether with a friend or a stranger, is meant to be a pleasant and leisurely pastime. The game is a contest of skill between two opponents of equal caliber, and if not of equal caliber then at least on an equal field.
Like any other sport, take basketball or football for example, even if the talent is not the same, the playing field is the same. In basketball, no matter where the two teams play, the court is 94 feet long and 50 feet wide. In football, opposing teams know they are fighting on a field that is exactly 100 yards long and 53 1/3 yards wide. In any case, players know that they will be playing on a pitch or field without irregularities and without surprises. The same cannot always be said for the game of billiards.
When a pool table is not properly cared for, there can and will be many irregularities and surprises. These insecurities surely make for an annoying and frustrating game without any pleasure.
5 ways to test your pool table for damage
From time to time you may need to have the felt surface of your pool table repaired or replaced. While that’s true, you should almost never need to replace your table’s rail pads.
With proper use and care, a pool table’s rail pad rubber has a lifespan of 25-50 years. This lifespan will be greatly reduced if your table is used improperly, exposed to extremes of temperature or humidity, or stored improperly.
Extreme heat, cold or humidity can cause your table’s rail rubber to become brittle or very hard. Here are five tests you can run to determine if your pool table has suffered significant rail rubber damage:
Listen – Shoot a ball in each track. The ball should rebound at a moderate to high speed, but most importantly, you should be able to hear the exact same sound as you walk around the table. Squeeze – Using the pressure of your fingers, systematically walk around the table and squeeze the rail pads of your table. You should be able to squeeze the pillow a moderate distance between 1/8 inch and 1/4 inch. Feel – Run your hands with your fingers around and under the table rails where the edges hang over the table’s playing surface. You feel for worn grooves and tracks under the felt. If you find any, it is an indication of worn cushions. This type of wear causes the rails to “bounce” less. Spin – Shoot a ball straight into each rail with high speed and moderate topspin. If the ball bounces more than 1 inch, the rail pads likely need to be replaced. Rebound – Slowly roll a ball up each rail and watch the reaction. If the ball comes to a standstill, your rails are worn and need to be replaced. If, on the other hand, the ball bounces back into the field, everything is fine. Also note the rebound angles. If the rebound matches the angle of incidence, you’re in good shape.
4 must-have pool table accessories for proper table maintenance
Pool Table Cover – Always cover your table after use, no exceptions. Horse Hair Brush – You might be tempted to buy a synthetic bristle brush, but horse hair is much softer and gentler on the table felt. Vacuum – Use a low-suction vacuum to remove dirt from the table surface. Soft towels – Dirty balls cause excessive wear on the playing surface. Use hot water and a soft towel to clean them every few games.
With these tips, you can enjoy your table for many years to come.
How to Replace Pool Table Cushions in 1 Hour
Replacing pool table cushions and rails is simple and straightforward. All you need is a new set of rails, a staple gun, glue, a sharp knife and a straight edge! If you’re trying to save some money and keep your trusty pool table, you can learn how to replace pool table rails by reading this 5-part guide.
Pool table cushions are said to last 20-25 years, but like everything else in life, this isn’t always the case. Sometimes splints can fail after only 5-10 years of play. Of course, this all depends on the usage and maintenance of your pool table. For those who play occasionally, your pool table will last up to almost 20 years without any problems. Pool tables used in bars, pubs and other commercial establishments tend to be used much more often which causes the cushions to wear out much faster.
How to tell if you need to replace pool table cushions
You can tell if your pool table cushions need replacing as they no longer offer as much bounce as they used to when balls make contact. You will hear a deep “roar”. This indicates a worn rail that needs to be replaced with performance rails that will completely change the game.
Pool table rails tend to go out around the same time, so we recommend replacing all six cushions at once. Cheaper, lower quality tables use K-66 rubber rails, which are usually pink. Power rails are often amber or tan in color. Although you can’t tell what color your rails will be once installed, you can do a quick endurance test to see if your pads need replacing.
The resilience test for pool tables
Roll a ball against the rails of your pool table. The ball should bounce against the side rails 3-4 times before coming to rest. When it falls short, your pool table cushions will need replacing.
Replacing the pool table rail
Some billiard table manufacturers try to keep prices down by opting for cheaper rails. They cut costs and buyers can’t see them. To learn how to identify quality pool tables, you should read the pool table buyer’s guide. Some players have noticed issues with brands like American Heritage and Artisan. That being said, pool table cushions will eventually need to be replaced if you want to maintain your well-oiled machine.
Gaming Tables Online.com carries only the best pool tables. While some sites have inventory in the thousands of pool tables, we hand select each item to ensure a high level of quality control. This gives customers peace of mind and confidence when shopping with us. see the difference
How to Replace Pool Table Cushions – The 5 Part Guide!
summary
To replace worn pool table rails you will need to remove the spring bar, remove the felt cloth, remove the stirrups and use a scraper to remove excess glue. Installing new rails involves gluing on new rubber rails, cutting the rail to length, attaching rubber ends, and basting a new cloth over the rail.
Game Tables Online made a video transcript of a YouTube video of The Pool Table Guy. In this post you will find all the instructions you need to replace your pool table cushions. Thanks for the great video R. Steven Schaffer!
Part 1 – Removing the rails and felt
Begin by removing the rails. Most billiard table rails are bolted. Once you’ve unscrewed them, pull the rails up and out and they’ll pop off. Use a razor to cut the length of the splint. Then remove the spring strip that runs the length of the rail. The spring strip sits in a groove in the rail and keeps the cloth tucked away. Turn the splint over and remove as much felt as possible by hand. The rest will be removed in the next step. Use needle nose pliers to remove staples and the rest of the fabric. While it’s best to get as many staples out as possible, it’s not necessary to remove every single one. Just make sure when you’re attaching the new fabric you’re not trying to staple onto the old staple.
Part 2 – Remove trim and glue
Remove fairing. The fairing is the end cap of the rubber rails. With the panel removed you can pry off the old rubber railing. Use a scraper to remove any remaining chimney and rubber elements to ensure a clean fit when new rails are installed. Apply a liberal coat of 3M Scotch-Weld Contact Adhesive-10 to the splint and pad. Let the glue sit until it becomes tacky. This will ensure that your new splint will stay in place once it is seated on the wood.
While you’re waiting for the glue to dry, check out some of these cool cue sticks to go with your new rails!
Part 3 – Align new rails
Place a new rubber splint on the wood. Placement matters and can affect the game. Use your hand to guide the splint in place to ensure it’s in the perfect position. Repeat this step if necessary. You don’t want your new splints to be at the wrong angle, or you’ll have to remove them and do it all over again! Using a straight edge, mark the ends of the pillow. Follow the angle of the rail above to leave an angle to place your new panels. Use a sharp knife to cut off the ends. You probably don’t want to get by with box cutters, as their length will affect your ability to make a clean and even cut.
Part 4 – Installing New Facings
Glue on the panels. Make sure they are flush with the rubber rails. Trim the excess off the trim with a knife. Use the contour of the pad splint as a guide.
Part 5 – The final touch
Lay a new strip of rail cloth over the channel in the rail where your spring strip came from. Leave some excess cloth on both ends of the splint so you can staple the cloth to the back of the splint. Lay the spring strip in place. Use a hammer to gently tap the spring strip into the channel to hold the felt in place. Make a relief cut at each end of the splint to allow the cloth to fold over easily for basting. Use a block of wood to ensure the spring strip is in place. It won’t be completely flush, but you should expect the spring strip to be raised just a tad higher than the actual rail. This is because of the space that the felt occupies in the channel. Trim off any excess felt inside the feather strip for a clean and professional look. Holding the felt cloth snugly, fold the cloth tightly along the contours of the splint. Staple the cloth in place. Walk along the railing, tighten and pin the cloth. You want the felt to be snug, but not so tight that it affects the shape of your splints. Finally, fold and staple the other end of the felt to the railing and viola, you have successfully replaced your pool table cushions! Let the games begin!
More pool table repair guides:
Related searches to pool table cushion replacement
Information related to the topic pool table cushion replacement
Here are the search results of the thread pool table cushion replacement from Bing. You can read more if you want.
You have just come across an article on the topic pool table cushion replacement. If you found this article useful, please share it. Thank you very much.
